Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Easymount EM-S880
Summary of Contents for Easymount EM-S880
- Page 1 EM-S1400C, EM-S1600C, EM-S1400H, EM-S1600H, EM-S880...
- Page 2 Contents Page 2 - Introduction Page 3 - Safety Instructions and environmental requirements Page 4 - Control panel and specifications Page 5 to 8 - Installation of laminating films Page 9 to 10 - Loading of media rolls Page 11 to 13 - Trouble shooting guide Page 14 –...
- Page 3 Emergency stop handle Magic eye Easy to use safety feature control panel Media mandrel [Excludes EM-S880] Drop down feed tray [Excludes EM-S880] The EM-S880 model does not have a media mandrel, take up unit and the feed tray is fixed.
-
Page 4: Safety Instructions
Safety Instructions • Please ensure that the voltages of the power supply you are using match with rated working voltages before operating the machine • The power supply should be close to the system for convenient use • The power supply should provide reliable protective earthing connection •... -
Page 5: The Control Panel
The Control Panel Easymount Cold Easymount Single Heated Roller Specifications EM-S880 EM-S1400C EM-S1600C Max. Laminating Width 880mm 1420mm 1620mm Max. Laminating Thickness 15mm 25mm Laminating Speed 3.5m/min 5m/min Rated Working Voltage/Frequency 220V-240V, 50Hz-60Hz Rate Input Power Dimensions 1200 x 630 x 1295... - Page 6 Loading of Laminating Films 1. Position the system on its stand and place the mandrels in the mandrel brackets. 2. Lock the mandrels in place by turning the black locking collars anti-clockwise. Connect the foot pedal to the power socket as shown in the above picture. 3.
- Page 7 4. Lift the Roller up by turning the handle anti-clockwise, Feed the film directly over the top laminating roller and through to the back of the system. 5. Move towards the 5. Move towards the rear of the system rear of the system a and pull the laminate pull the laminate tight tight from the middle...
- Page 8 Alter the speed to your preference If you are using the Easymount by turning the speed control knob. Sign single hot, you can select Hot During loading we advise a slow or cold.
- Page 9 10. Loosen the waste backing paper along the length of the laminate, pull up the waste backing paper only from 9. Loose the backing paper along the length of the laminate and pulling up only from the middle stick this to the the middle and stick onto the waste mandrel using tape.
- Page 10 Loading Media Rolls 1. Remove the media mandrel, load the media onto the system, lock into place and ensure it is centralized. If the media is the same size as the laminate please align the media and laminate together. 1. Remove the Media mandrel, load the media onto the system, lock into place and ensure it is centralized. If the media is the same size as the laminate, please ensure these are Tensioning the rolls: Media Mandrel - Depending on how straight...
- Page 11 4. Pull both the laminating film and media tightly together in the centre at the back of the system. Lower the 4. Pull both the laminating film and media tightly together at the back of the system in the middle. Lower the laminating roller and check the media and laminate are tight against the rollers and are correctly aligned.
-
Page 12: Troubleshooting Guide
Troubleshooting guide If the media is buckling/bowing in the middle as shown in the below picture you have used too much roller pressure and/or incorrect feeding: Incorrect roller pressure: Higher the laminating roller, pull the material from the middle at the rear of the system and start to lower the roller slowly. - Page 13 Incorrect tension applied to film and/or waste backing paper: The above picture shows either not enough tension to the laminate or too much tension to the waste backing • Laminating film requires tension to stop creasing. Ensure the laminate has plenty of tension. The backing paper.
- Page 14 Incorrect loading of the laminate: The picture to the left shows the laminate is not tight to the roller on one side. Raise the • When loading the laminate or media pull laminating roller, pull the laminate from the from the back in the centre, lower the roller and centre at the rear of the system [ensuring check to ensure it is tight against the laminating the laminate is tight against the roller on...
-
Page 15: Laminating Adjustments
The Easymount Sign Cold system does not have a temperature control and operates cold. The Easymount Sign Hot system has the option of a heat assisted top roller with a fixed temperature of 45°C/113°F. By using heat it will soften the adhesive and reduces ‘silvering’ when laminating. -
Page 16: Warranty & Incorrect Use
IMPORTANT INFORMATION Your Easymount Sign laminator should reach you in perfect condition and is guaranteed for 1 Year from date of purchase covering defective parts and general wear and tear, this does not cover film jams, misfeeds or other operator related errors, which would be chargeable.