Related Manuals for Easymount EM-1200
Summary of Contents for Easymount EM-1200
- Page 1 Product instruction manual Easymount Wide Format Laminators The Easymount has been designed to be user friendly, however we strongly recommend you take a few minutes to read through this manual to ensure correct operation. Keep this manual safe for future reference.
-
Page 2: Table Of Contents
Contents Page 3 - Introduction Page 4 - Safety Instructions and Environmental requirements Page 5 - Control panel and specifications Page 6 - Installation of laminating films Page 7 - Film loading Page 8 - Feeding the film and cold laminating Page 9 - Cold laminating and Single Hot laminating Page 10 - Mount film and optional extras Page 11- Laminating adjustments... -
Page 3: Introduction
Easymount is a high performance wide format mounting and laminating system with a solid construction built to last. The Easymount is great for mounting prints to boards and applying pressure sensitive laminates as well as applying application tapes, double sided adhesives and vinyls. -
Page 4: Safety Instructions
Safety Instructions • Please ensure that the voltages of power supply you are using match with rated working voltages before operating the machine • The power supply should be close to the machine for convenient use • The power supply should provide reliable protective earthing connection • This machine must be earthed reliably so as to ensure the safety of the machine during operation • Only the operators of this machine should operate the electric or motion... -
Page 5: Specifications
The Control Panel Easymount Cold Easymount Single Heated Roller (SH) Specifications EM-1200 EM-1400 EM-1600 Max Laminating Width 1200mm / 47” 1400mm / 55” 1600mm / 63” Max Laminating Thickness 25mm / 1” Temperature of Rubber Roller Ambient temperature to 60°C / 140°F... -
Page 6: Installation Of Laminating Films
Installation of Laminating Films Pressure sensitive film (loaded on the top mandrel) 1. Remove the top mandrel from the 2. Loosen the two fastening screws 5. Re-load the mandrel on to the mandrel support brackets on one of the mandrel core grips, bracket with the film feeding from the bottom of the mandrel if the slide off one side. -
Page 7: Film Loading
Film Loading Pressure sensitive film (loaded on the top mandrel) 1. Lift the feed tray to the upright (Safety guard lock) 2. Peel back the liner paper from the position and lock securely. Following film, exposing the adhesive side of the loading diagram on the left the laminate and stick release liner to cabinet of the machine, pull the film... - Page 8 Feeding the Film 2. Place vinyl/print through rollers 5. Using the safety cutter provided 1. Using the pressure handle raise the from feed tray and onto back plate slice between the release paper and upper roller film cutting only the release paper 3.
- Page 9 Laminating - SINGLE HOT 1. The single heated Easymount can 2. Set the temperature to 3. Plug in the foot pedal be run either cold or warm to switch approximately 40°C/104°F using...
- Page 10 Mount Film 1. Position the mount film centrally 2. Pull the mount film up and 3. Stick it to the exposed pressure on the mandrel and lift it into towards the bottom roller. sensitive film as before. * Ensure the position on the brackets sticky side of the mount film is facing towards you and away from the...
-
Page 11: Laminating Adjustments
5. Put a spare core onto the take up the bracket is sprung loaded on mandrel the unmotorised unit). Then using double sided tape attach media/ laminate to the core, the Easymount laminator is now ready to run prints reel to reel. Laminating adjustments Temperature Most pressure sensitive films benefit from around 40°C / 104°F of heat being applied to help elliminate ‘silvering’... -
Page 12: Trouble Shooting
Trouble Shooting Problem Media lifting and wrinkling going through the rollers. This is caused by adding too much roller pressure. Solution Take pressure off rollers and drop down The media will then correct itself and run loosely into the neutral position. through smoothly. - Page 13 Problem Film running loose and climbing up onto the take up core. This occurs when there is NO tension added to the film. Solution Firstly, ensure the core collars are Add tension to the film by turning the core collar in the TIGHT to the shaft by tightening directions shown.
- Page 14 OR Run media from the top mandrel This is the preferred method when at the back of the Easymount, laminating a long run as the media missing out the feed tray. naturally tensions over the bottom roller.
- Page 15 Problem Creasing on laminate. This can occur when the laminate is loaded incorrectly. Solution Lift Rollers. Pull media tightly from the back of the system. This will enable the laminating film and media to ‘coat’ the rollers evenly. Before running, ensure that the film is smooth and tight to the rollers.
-
Page 16: Warranty And Incorrect Use
IMPORTANT INFORMATION Your Easymount laminator should reach you in perfect condition and is guaranteed for 1 Year from date of purchase covering defective parts and general wear and tear, this does not cover film jams, misfeeds or other operator related errors, which would be chargeable.
Need help?
Do you have a question about the EM-1200 and is the answer not in the manual?
Questions and answers