Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Norac Manuals
  4. Control Systems
  5. UC4.5
  6. Installation manual

Norac UC4.5 Installation Manual

Hide thumbs Also See for UC4.5:

Advertisement

Quick Links

Download this manual
Summers
(Main Lift and Enhanced Stability Option)
Installation Manual
SM3

Advertisement

loading
Need help?

Need help?

Do you have a question about the UC4.5 and is the answer not in the manual?

Questions and answers

Related Manuals for Norac UC4.5

Summary of Contents for Norac UC4.5

  • Page 1 Summers (Main Lift and Enhanced Stability Option) Installation Manual...
  • Page 2 Reorder P/N: UC4.5-SM3-INST Rev C (Summers Main Lift and Enhanced Stability Option) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...

  • Page 3: Table Of Contents

    Contents Introduction ........................ 1     Kit Parts ........................2     Hydraulic Installation ....................5     Main Lift Sensor Installation ..................7     Roll Sensor Installation ....................8     Electrical Installation ....................10     Software Setup ......................12  ...

  • Page 4: Introduction

    Introduction Congratulations on your purchase of the NORAC UC4.5 Spray Height Control System. This system is manufactured with top quality components and is engineered using the latest technology to provide operating reliability unmatched for years to come. When properly used the system can provide protection from sprayer boom damage, improve sprayer efficiency, and ensure chemicals are applied correctly.

  • Page 5: Kit Parts

    Kit Parts Hydraulic Plumbing Figure 1: SM3 Hydraulic Plumbing...
  • Page 6 List of Parts The following tables list the Summers main lift and enhanced stability kit (SM3) specific parts of the NORAC UC4.5 system. This kit is to be used when installing the proportional main lift option with existing Summers installations.
  • Page 7 P - PIPE Do not use high speed power tools/drills when installing hardware. The use of dielectric grease is not recommended on any NORAC electrical connections. To ensure all stainless steel hardware does not gall or seize apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation.

  • Page 8: Hydraulic Installation

    Hydraulic pressure will exist on the main lift circuit unless the main lift is all the way down. Component failure due to oil contamination is not covered under the NORAC UC4.5 system warranty. It is recommended that a qualified technician perform the hydraulic installation. Expansion Block Assembly 1.
  • Page 9 3. Install the 6MB 6MJ fitting (F04) into the “B” port of the expansion block. 4. Install the 6MBP plug (F03) into the “A” port of the expansion block. 5. If the valve block is not already installed on the sprayer, install it as outlined in the UC4.5 Spray Height Control installation manual.

  • Page 10: Main Lift Sensor Installation

    Main Lift Sensor Installation 1. Assemble and mount the main lift sensor bracket as shown in Figure 3. 2. Mount the sensor onto the sensor mounting collar (Figure 3). Figure 3: Main Lift Sensor Mounted in the Correct Location...

  • Page 11: Roll Sensor Installation

    Roll Sensor Installation 1. Securely mount the roll sensor to the included roll sensor bracket using the #6 machine screws. Tighten screws to 10 in-lbs (1.1 Nm). 2. The orientation of the mounted roll sensor to the roll sensor bracket will depend on the bracket mounting.
  • Page 12 3. The roll sensor is to be mounted onto the chassis as shown in Figure 6. Ensure the roll sensor is relatively level when chassis is level. Figure 6: Chassis Roll Sensor Mounting 4. Ensure that the chassis roll sensor (Figure 6) has the highest serial number and that the boom frame roll sensor (previously installed) has the lowest serial number (Figure 7).

  • Page 13: Electrical Installation

    1. Connect the 6-pin shroud (S6) on C17 to T6 on C11 (previously installed). 2. Disconnect the existing C13 cable and install the 3-pin connectors between it and C11. One connector on C17 will remain disconnected. It is used when installing other UC4.5 options.
  • Page 14 3. Install the two connectors on the end of cable C17 to the expansion block. The connector marked “Main Up” goes on the port side of the block. The port side of the block is the side with the hoses. 4.

  • Page 15: Software Setup

    3. Turn on the power for the control panel using the switch on the side of the chassis. 4. Refer to the UC4.5 Spray Height Control Operator’s Manual to run an automatic install with the SM3 type selected.

  • Page 16: Cable Drawings

    Cable Drawings ITEM C07: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M...
  • Page 17 ITEM C17: 44658-45D – CABLE UC4 VALVE MAIN DT...
  • Page 18 TOPCON Agriculture Canada 3702 Kinnear Place Saskatoon, SK S7P 0A6 TOPCON Agriculture Americas W5527 Hwy 106 Fort Atkinson, WI 53538 TOPCON Precision Agriculture Europe Avenida de la industria, 35, Tres Cantos, España Spain Support Phone: 888 979 9509 E-mail: tasupportn@topcon.com Web: www.norac.ca...