Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Norac Manuals
  4. Paint Sprayer
  5. UC4.5
  6. Installation manual

Norac UC4.5 Installation Manual

Spray height control system h ardi economy hpz and haz (18-30m) dah09
Hide thumbs Also See for UC4.5:

Advertisement

Quick Links

Download this manual
HARDI Economy
HPZ and HAZ (18-30m) DAH09
Installation Manual
HD11

Advertisement

loading
Need help?

Need help?

Do you have a question about the UC4.5 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Norac UC4.5

Summary of Contents for Norac UC4.5

  • Page 1 HARDI Economy HPZ and HAZ (18-30m) DAH09 Installation Manual HD11...
  • Page 2 Economy HPZ and HAZ (18-30m) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...

  • Page 3: Table Of Contents

    Contents Introduction ........................ 1     General UC4.5 System Layout ................. 2     Kit Parts ........................3     Ultrasonic Sensor Installation .................. 5     Roll Sensor Installation .................... 10     Electrical Installation ....................12    ...

  • Page 4: Introduction

    Introduction Congratulations on your purchase of the NORAC UC4.5 Spray Height Control System. This system is manufactured with top quality components and is engineered using the latest technology to provide operating reliability unmatched for years to come. When properly used the system can provide protection from sprayer boom damage, improve sprayer efficiency, and ensure chemicals are applied correctly.

  • Page 5: General Uc4.5 System Layout

    General UC4.5 System Layout Figure 1 illustrates the general layout of the UC4.5 system components: Figure 1: General UC4.5 System Layout Do not use high speed power tools/drills when installing hardware. The use of dielectric grease is not recommended on any NORAC electrical connections.

  • Page 6: Kit Parts

    Kit Parts Kit Overview Figure 2: HD11 System Parts...
  • Page 7 UC5 NETWORK COUPLER 2-WAY 43764T UC5 NETWORK COUPLER 2-WAY WITH TERMINATOR UC4.5-BC-MANUAL- OPERATOR MANUAL UC4.5 SPRAY HEIGHT CONTROL OPERATOR UC4.5-BC-HD11-INST MANUAL INSTALLATION UC4.5 HARDI ECONOMY HPZ AND HAZ (18-30M) 102084 TOOL PIN REMOVAL G.P. WITH NORAC LOGO 105882 UC5 NETWORK 6 PIN PLUG...

  • Page 8: Ultrasonic Sensor Installation

    Ultrasonic Sensor Installation Bracket Assembly Assemble the breakaway sensor bracket as illustrated in Figure 3, following the instructions below. Figure 3: Breakaway Bracket Assembly 1. Compress the spring and insert it together with the collar into the base. 2. Slide the tube through the assembled part. 3.
  • Page 9 Ultrasonic Sensor Serial Number Arrangement When installing the sensors, start with the smallest serial number on the left-hand side, and proceed to the largest serial number on the right hand side. Each sensor has a serial number stamped on the sensor housing. Apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation.
  • Page 10 (D). 6. The sensor bracket should be oriented forward (ahead of the boom). 7. Mount the NORAC ultrasonic sensor into the sensor bracket and run the sensor cable through the sensor tube. A problem can arise if a sensor is not mounted correctly. It is possible for the sensor to read off of the boom instead of the ground.
  • Page 11 Wing Bracket Mounting Below is the suggested mounting location for the wing sensor brackets. Mounting location is just inside of the boom break-away section (A). Figure 7: Suggested Bracket Mounting Location (viewed from front) IMPORTANT: Avoid mounting the bracket too close to the touch-down wheel (B).
  • Page 12 Main Lift Sensor Installation 1. Mount the main lift bracket (B11) as illustrated in Figure 8. Ensure sensor cable is routed properly and securely fastened. 2. Mount the Ultrasonic sensor to the bracket. Ensure the sensor has a clear view of the ground.

  • Page 13: Roll Sensor Installation

    Roll Sensor Installation Bracket Assembly 1. Securely mount the roll sensors to the included roll sensor brackets using the #6 machine screws. Tighten screws to 10 in-lbs (1.1 Nm). 2. The orientation of the mounted roll sensor to the roll sensor bracket will depend on the bracket mounting.
  • Page 14 Roll Sensor Mounting Ensure the 6 pin connector is pointing towards the right hand wing (when looking from the rear of the sprayer). Fasten with cable ties. 1. Install one roll sensor (E04) onto the non-rotating part of the boom. 2.

  • Page 15: Electrical Installation

    (Bottom of switch pressed IN). Use caution when handling the 12 V power line of the sprayer wiring. 1. Install the UC4.5 Control Panel (E01) in the cab of the sprayer using the included mount (B06). Mount the panel where it will be clearly visible and within easy reach of the operator.
  • Page 16 8. Connect the DB15 connector of cable C12 to the DAH09 DB15 connector. 9. Connect the red wire with spade connector on C12 to the Switched 12VCC on the DAH09 board (Figure 13). 10. Connect the black wire with spade connector on C12 to the GND on the DAH09 board (Figure 13).
  • Page 17 Figure 15: Default Slant Direction Wiring  However, if the boom does the opposite of what is described above, it is necessary to swap the E and F wires in the S6 connector of 44658-78 (C12). 12. Connect the 6-pin tower (T6) on the interface cable (C17) to the mating 6-pin shroud (S6) on C11.

  • Page 18: Software Setup

    2. If any functions do not work, review this manual to check for proper installation. 3. Turn on the power for the UC4.5 Control Panel using the switch on the side of its chassis. 4. The procedure for the installation of the UC4.5 Spray Height Control system is now complete.

  • Page 19: Cable Drawings

    Cable Drawings ITEM C05: 43210-20 - CABLE UC5 NETWORK 18 AWG - 20M ITEM C07: 43220-01 - CABLE UC5 NETWORK 14 AWG - 1M...
  • Page 20 ITEM C10: 44650-52 - CABLE UC4.5 POWER HARDI...
  • Page 21 ITEM C11: 44651-51 - CABLE UC4.5 EXTENSION VALVE HARDI...
  • Page 22 ITEM C12: 44658-78 - CABLE UC4 BC INTERFACE HARDI DAH09...
  • Page 23 ITEM C17: 44658-107 - CABLE UC4.5 INTERFACE TWIN / FORCE DEMO...
  • Page 24 TOPCON Agriculture Canada 3702 Kinnear Place Saskatoon, SK S7P 0A6 TOPCON Agriculture Americas W5527 Hwy 106 Fort Atkinson, WI 53538 TOPCON Precision Agriculture Europe Avenida de la industria, 35, Tres Cantos, España Spain Support Phone: 888 979 9509 E-mail: tasupportn@topcon.com Web: www.norac.ca...