1. Manuals
  2. Brands
  3. Norac Manuals
  4. Paint Sprayer
  5. UC4.5
  6. Installation manual

Norac UC4.5 Installation Manual

Spray height control system hardi aftermarket north america/australia
Hide thumbs Also See for UC4.5:
Table of Contents

Advertisement

Quick Links

Download this manual
Hardi Aftermarket North America/Australia
Installation Manual
HD1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UC4.5 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Norac UC4.5

Summary of Contents for Norac UC4.5

  • Page 1 Hardi Aftermarket North America/Australia Installation Manual...
  • Page 2 Reorder P/N: UC4.5-BC-HD1-INST Rev B (Hardi Aftermarket North America/Australia) NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information...

  • Page 3: Table Of Contents

    Contents Introduction ........................ 1     General UC4.5 System Layout ................. 2     Kit Parts ........................3     Existing System Check ....................8     Ultrasonic Sensor Installation ................10     Roll Sensor Installation .................... 14  ...

  • Page 4: Introduction

    Introduction Congratulations on your purchase of the NORAC UC4.5 Spray Height Control System. This system is manufactured with top quality components and is engineered using the latest technology to provide operating reliability unmatched for years to come. When properly used the system can provide protection from sprayer boom damage, improve sprayer efficiency, and ensure chemicals are applied correctly.

  • Page 5: General Uc4.5 System Layout

    General UC4.5 System Layout Figure 1 illustrates the general layout of the UC4.5 system components: Figure 1: General UC4.5 System Layout...

  • Page 6: Kit Parts

    Kit Parts Kit Overview Figure 2: HD1 System Parts...
  • Page 7 Hydraulic Plumbing Figure 3: HD1 Double Acting Hydraulic Plumbing...
  • Page 8 Figure 4: HD1 Single Acting Hydraulic Plumbing...
  • Page 9 UC5 NETWORK 6 PIN PLUG 44963D VALVE BLOCK ASSEMBLY 2 STATION CC/LS PROP DT 4 BOLT Optional Main Lift Kit An optional main lift sensor kit is available for purchase from NORAC. Part Number Name 4570BC UC4.5 MAIN LIFT OPTION - 44743...
  • Page 10 NOTE: Not all fittings are used for this installation. Do not use high speed power tools/drills when installing hardware. The use of dielectric grease is not recommended on any NORAC electrical connections. To ensure all stainless steel hardware does not gall or seize apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation.

  • Page 11: Existing System Check

    Existing System Check 1. Before beginning the install, ensure all hydraulic boom functions are operating properly on the sprayer.  All Fold Functions  Main Lift Function  Wing Tilt Functions  Slant Function 2. Inspect slide pads and wear surfaces for excessive wear. Replace or adjust if necessary. 3.
  • Page 12 8. Record the time (seconds) it takes for a full stroke for all boom functions. To ensure repeatable measurements, take the average of 3 trials. 9. Not all sprayers will have the functions listed below in Figure 6. Ensure the boom has sufficient travel so it does not contact the ground during these tests.

  • Page 13: Ultrasonic Sensor Installation

    Ultrasonic Sensor Installation Bracket Assembly Assemble the breakaway sensor bracket as illustrated in Figure 7, following the instructions below. Figure 7: Breakaway Bracket Assembly 1. Compress the spring and insert it together with the collar into the base. 2. Slide the tube through the assembled part. 3.
  • Page 14 Ultrasonic Sensor Serial Number Arrangement When installing the sensors, start with the smallest serial number on the left-hand side, and proceed to the largest serial number on the right hand side. Each sensor has a serial number stamped on the sensor housing. Apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation.
  • Page 15 Ultrasonic Sensor Mounting Guidelines The following guidelines will ensure optimal sensor performance and prevent sensor measurement error. These rules should be followed for both the wing sensors and the main lift (middle) sensor. 1. In its lowest position, the sensor must be 9 inches (23 cm) or more from the ground (A). 2.
  • Page 16 If the sensor is mounted to this portion of the boom, the system will force the boom downwards towards the ground as the boom folds backwards. 4. Mount the NORAC ultrasonic sensor into the sensor bracket and run the sensor cable through the sensor tube.

  • Page 17: Roll Sensor Installation

    Roll Sensor Installation Bracket Assembly 1. Securely mount the roll sensors to the included roll sensor brackets using the #6 machine screws. Tighten screws to 10 in-lbs (1.1 Nm). 2. The orientation of the mounted roll sensor to the roll sensor bracket will depend on the bracket mounting.
  • Page 18 Temperature Probe Once the block is mounted, fasten the temperature probe from E03 to the NORAC valve block using the included 3/8x1/2” bolt as illustrated in Figure 14. Figure 14: NORAC Valve Block with Temperature Probe Installed...

  • Page 19: Electrical Installation

    A good spot to mount the UC4.5 control panel is on the right hand side of the cab to the Roll Over Protection Bar. Four pilot holes for the screws provided need to be drilled to facilitate the control panel mounting.
  • Page 20 7. Connect the 6-pin tower on C03 to C04. Connect the 2-pin connectors on C03 to the NORAC valve block, as shown in Figure 16. 8. The connectors on the valve cable (C03) are marked RIGHT UP, LEFT UP, RIGHT DOWN and LEFT DOWN.
  • Page 21 IMPORTANT: Provide enough slack in all cables to account for the movement of the main section, parallel lift, and FOLDING boom movement. 13. The Hardi control box does not require the polarity of the power source to be Negative Ground. However, before connecting C10, ensure the Hardi system is wired as Negative Ground.

  • Page 22: Hydraulic Installation

    Valve Assembly – Double Acting 1. On a clean surface remove the plastic plugs from the block. 2. Install the 6MB 6MJ (F02) fittings into the “P” and “T” ports on the NORAC block. Tighten to 18 ft-lbs (24 Nm).
  • Page 23 4. Install the 6MB 6MJ (F02) fittings into the “B” ports on the NORAC block. Tighten to 18 ft-lbs (24 Nm). 5. Install the 6MBP (F03) plugs into the “A” ports on the NORAC block and tighten to 18 ft- lbs (24 Nm).
  • Page 24 Valve Block Mounting Ensure that no hydraulic components will interfere with any sprayer parts or be pulled tight at any time. The recommended mounting location is on the rear of the boom main section and on the vertical member centered below the Hardi valve block. Orient the valve block such that the "A"...
  • Page 25 Figure 3. 2. Install the 90 degree fittings on hoses H01 onto the “A” and “B” ports on the NORAC valve block. Route the free ends of the hoses to each of the wing tilt cylinders.
  • Page 26 2. After the NORAC valves are mounted, the hydraulic hoses and fittings can be plumbed following the schematic in Figure 4. 3. Install the 90 degree fittings on hoses H01 onto the “B” ports on the NORAC valve block. 4. Route the free ends of the hoses to each of the wing tilt cylinders.

  • Page 27: Software Setup

    2. If any functions do not work, review the hydraulic and electrical portions of this manual to check for proper installation. 3. Turn on the power for the UC4.5 Control Panel using the switch on the side of its chassis. 4. The procedure for the installation of the UC4.5 Spray Height Control system is now complete.

  • Page 28: 10 Cable Drawings

    10 Cable Drawings 10.1 ITEM C01: 44653-10 - CABLE UC4.5 ADAPTER MOLEX TO DEUTSCH 10.2 ITEM C03: 44656D – CABLE VALVE VARIABLE RATE DT...
  • Page 29 10.3 ITEM C04: 44651 - CABLE VALVE EXTENSION 10.4 ITEM C05: 43210-20 - CABLE UC5 NETWORK 18 AWG - 20M...
  • Page 30 10.5 ITEM C06: 43210-15 - CABLE UC5 NETWORK 18 AWG - 15M...
  • Page 31 10.6 ITEM C10: 44650-54 - CABLE UC4.5 POWER HARDI...
  • Page 32 TOPCON Agriculture Canada 3702 Kinnear Place Saskatoon, SK S7P 0A6 TOPCON Agriculture Americas W5527 Hwy 106 Fort Atkinson, WI 53538 TOPCON Precision Agriculture Europe Avenida de la industria, 35, Tres Cantos, España Spain Support Phone: 888 979 9509 E-mail: tasupportn@topcon.com Web: www.norac.ca...

Table of Contents