Page 2
ZTE CORPORATION or its licensors may have current or pending intellectual property rights or applications covering the subject matter of this document. Except as expressly provided in any written license between ZTE CORPORATION and its licensee, the user of this document shall not acquire any license to the subject matter herein.
Page 4
5.9.1 Configure the IGMP................5-25 5.9.2 Configure the MLD.................5-26 6 Configure the Local Network..............6-1 6.1 Check the Local Network Status................6-1 6.2 Configure the WLAN..................... 6-2 6.2.1 Configure the Basic Parameters of the WLAN........6-2 6.2.2 Configure the Advanced Parameters of the WLAN......... 6-5 6.3 Configure the LAN....................
Chapter 1 Safety Precautions Note Before using the device, read the following safety precautions. ZTE bears no liability to the consequences incurred by violation of the safety instructions. Usage Cautions Read all the safety cautions carefully before using the device.
Page 6
EU Declaration of Conformity Hereby, ZTE Corporation declares that the radio equipment type ZXHN H3601 is in compliance with Directive 2014/53/EU, The full text of the EU declaration of conformity is available at the following Internet address: http://support.zte.com.cn/support/cer/EU...
Page 7
1 Safety Precautions Environmental Information The equipment you purchased has required the extraction and use of natural resources for its production. It may contain substances that are hazardous to people’s health and to the environment. To avoid putting such substances into our environment and to reduce pressure on our natural resources, we ask that you reuse or recycle your end-of- life equipment by using an accredited electronics take-back system.
Hardware Connection....................2-4 2.1 Package Check After unpacking the product, check that the following items are complete. Name Quantity ZXHN H3601 AC-DC power supply adapter RJ-45 Ethernet cable User manual Note The list is only for reference. The actual contents may vary from the list.
Wi-Fi 5 GHz band 5250 – 5350MHz EIRP: 19 ± 1 dBm Wi-Fi 5 GHz band 5470 – 5725MHz EIRP: 26 ± 1 dBm 2.3 Hardware Description Front panel Figure 2-1 shows the front panel of the ZXHN H3601. Figure 2-1 The Front Panel SJ-20200429083356-004 | 2020-07-23(R1.0)
Page 11
Flashing: Software upgrade progress. Rear panel Figure 2-2 shows the interfaces and buttons on the rear panel of the ZXHN H3601. Figure 2-2 The Rear Panel Interface/Button Function USB 2.0 host port: Used for the USB storage device, printer or Dongle connection...
WPS Push Button 2.4 Hardware Connection Figure 2-3 shows the devices that are connected to interfaces of the ZXHN H3601. Figure 2-3 Cable Connection The factors affecting the wireless network coverage range include the location of the product, distance between the product and a wireless terminal, number of obstacles, obstacle material and density, and interference source.
Page 13
2 Product Overview The product should be far away from an electrical appliance with a strong magnetic or electric field, for example, a microwave oven, a refrigerator, a wireless router, a cordless phone, or a Bluetooth product. The product should be installed on the same floor as the applied area. ...
Chapter 3 Topology In the controller status and agent status, the corresponding topologies are different. If ZXHN H3601 is set to controller, the corresponding topology diagram is shown in Figure 3-1. Figure 3-1 Controller If ZXHN H3601 is set to agent, the corresponding topology diagram is shown in ...
4.1 Configure TCP/IP To log in to the ZXHN H3601 on a computer, you need to set the IP address of the computer to ensure that the IP address of the computer and the maintenance IP address of the ZXHN H3601 are in the same network segment.
IP address in the address bar of Internet explorer to access the system. Prerequisite A computer is directly connected to the ZXHN H3601, and their IP addresses are in the same network segment. Steps 1. Open Internet explorer, and enter http://192.168.1.1 (default maintenance IP address of the ZXHN H3601) in the address field.
Page 19
4 Configuration Preparation 2. Enter your username and password and click Login. The configuration page is displayed, see Figure 4-2. Figure 4-2 Configuration Page SJ-20200429083356-004 | 2020-07-23(R1.0)
5.1.1 Check the Ethernet Interface Information The section describes how to check the Ethernet interface status. Steps 1. On the main page of the ZXHN H3601, select Internet > Status > Ethernet Interface Information to the Ethernet Interface Information page, see Figure 5-1.
Steps Check the mobile network information. 1. On the main page of the ZXHN H3601, select Internet > Status > 3G/4G > Mobile Network to go to the Mobile Network page. The signal strength can verify the network card is plugged, see Figure 5-3.
2. Click Refresh to refresh the information. Check the 3G/4G connection status. 3. On the main page of the ZXHN H3601, select Internet > Status > 3G/4G > 3G/4G Connection Status to go to the 3G/4G Connection Status page, see Figure 5-4.
Page 24
ZXHN H3601 Maintenance Management Guide Steps 1. On the main page of the ZXHN H3601, select Internet > WAN > Ethernet to the Ethernet Connection page, see Figure 5-5. Figure 5-5 Ethernet Connection page Table 5-1 lists the new item parameters.
Page 25
Subnet Mask Subnet mask of ZXHN H3601. Gateway It is usually the IP address of the ZXHN H3601 by default. IP address of the DNS server for static connections. You can set DNS1-DNS3 up to three IP addresses for the server. These IP addresses are provided by the ISP.
2. Click Apply button to apply the changes. 5.2.2 Configure the 3G/4G A Dongle device can be connected to ZXHN H3601 through a USB interface. If the Dongle has a 3G/4G(SIM) card inserted, the ZXHN H3601 can access the Internet through the Dongle device.
Page 27
5-6. Figure 5-6 Mobile Network 3. Click Refresh to refresh the information. 4. On the main page of the ZXHN H3601, select Internet > WAN > 3G/4G to the 3G/4G Connection page. Table 5-3 lists the New Item parameter. After the setup is complete, you can see the...
Page 28
Select on/off NAT switch function. Figure 5-7 New 3G/4G Connection 5. Click Apply button to apply the changes. 6. On the main page of the ZXHN H3601, select Internet > Status > 3G/4G to the 3G/4 G Connection Status page, see Figure 5-8.
Packets that match no classification rules will be processed according to the default policy showed in this page. Steps 1. On the main page of the ZXHN H3601, select Internet > QoS > QoS Global Configuration to the QoS Global Configuration page, see Figure 5-9.
Page 30
ZXHN H3601 Maintenance Management Guide Steps 1. On the main page of the ZXHN H3601, select Internet > QoS > Classification to the Classification page. 2. Click to create new QoS classification, see Figure 5-10. Figure 5-10 New QoS Classification Page Table 5-4 lists the QoS classification configuration parameters.
5 Configure the Internet Parameter Description Packets Classification Criterion Set radiobox On to enable all Interface. All Interface Ingress If setting radiobox Off to disable all Interface, specify the data traffic direction. Source MAC Address Source host MAC address. Destination MAC Address Destination host MAC address.
Page 32
ZXHN H3601 Maintenance Management Guide Steps Firewall 1. On the main page of the ZXHN H3601, select Internet > Security > Firewall to the Firewall page, see Figure 5-11. Figure 5-11 Firewall Page 2. Set the parameters. For a description of the parameters, refer to Table 5-5.
The section describes how to configure filter criteria. Steps Filter Switch and Mode Configuration 1. On the main page of the ZXHN H3601, select Internet > Security > Filter Criteria to the Filter Criteria page. 2. Click Filter Switch and Mode Configuration to the configuration page, see Figure 5-13.
Page 34
ZXHN H3601 Maintenance Management Guide Table 5-7 Parameter Descriptions for the Filter Switch and Mode Configuration Parameter Description Filter Set radiobox On to enable the URL filter function. Mode Enable the URL filter function. There are two modes: Black List ...
Page 35
5 Configure the Internet Figure 5-15 IP Filter Page Table 5-9 lists the IPv4 filter parameters. Table 5-9 Parameter Descriptions for the IPv4 Filter Parameter Description On/Off Set radiobox On to enable the function of IP filter. Name Name of the IP filter item. The name must be specified.
The section describes how to configure local service control. Steps Service Control-IPv4 1. On the main page of the ZXHN H3601, select Internet > Security > Local Service Control to the Local Service Control page. 2. Click Service Control-IPv4 to open Service Control-IPv4 page, see Figure 5-16.
Page 37
If the Ingress is WAN_All, all the WAN connection can access ZXHN H3601. If the Ingress is LAN, the LAN side can access ZXHN H3601. IP Range The IP address segment that needs to be filtered.
Page 38
Specify the data stream inbound direction, and this parameter must be specified. If the Ingress is WAN_All, all the WAN connection can access ZXHN H3601. If the Ingress is LAN, the LAN side can access ZXHN H3601. Prefix IPv6 address prefix. Service Type Type Specify the service that is permitted or denied to access.
5.4.4 Configure the ALG The section describes how to configure ALG. ALG provides the relevant parameters of security configuration function. Steps 1. On the main page of the ZXHN H3601, select Internet > Security > ALG to the ALG page, see Figure 5-19.
URL, instead of an IP address. Steps 1. On the main page of the ZXHN H3601, select Internet > Security > Port Forwarding to the Port Forwarding page, see Figure 5-21.
3. Click Apply button to apply the changes. 5.5 Configure the Parental Controls The section describes how to configure parental controls. Steps 1. On the main page of the ZXHN H3601, select Internet > Parental Controls to the Parental Controls page, see Figure 5-22.
ZXHN H3601 Maintenance Management Guide Figure 5-22 Parental Controls 2. Configure the parental controls parameters. Table 5-15 lists the parental controls parameters. Table 5-15 Parental Controls Parameters Parameter Description Click On to enable the parental controls function. On/Off Name The name of parental control.
Page 43
5 Configure the Internet Steps 1. On the main page of the ZXHN H3601, select Internet > DDNS to the DDNS page, Figure 5-23. Figure 5-23 DDNS Configuration Page 2. Configure the DDNS parameters. Table 5-16 lists the DDNS parameters.
The section describes how to configure SNTP. SNTP provides the parameters of SNTP configuration features. Steps 1. On the main page of the ZXHN H3601, select Internet > SNTP to the SNTP page, Figure 5-24. Figure 5-24 SNTP Configuration Page 2.
The section describes how to configure Port Binding. Port Binding provides the parameters of Port Binding configuration features. Steps 1. On the main page of the ZXHN H3601, select Internet > Port Binding to the Port Binding page, see Figure 5-25.
5.9.2 Configure the MLD The section describes how to configure MLD. MLD provides the parameters of MLD configuration features. Steps 1. On the main page of the ZXHN H3601, select Internet > Multicast > MLD to the MLD page, see Figure 5-27.
Status, LAN Client Status and USB Storage Status. The relevant information of Local Network status is shown as below. Steps 1. On the main page of the ZXHN H3601, select Local Network > Status to the Local Network Status page, see Figure 6-1.
The section describes how to configure WLAN basic settings. Steps WLAN On/Off Configuration 1. On the main page of the ZXHN H3601, select Local Network > WLAN > WLAN Basic to the WLAN Basic page, see Figure 6-2. Figure 6-2 WLAN On/Off Configuration Table 6-1 lists the WLAN on/off configuration parameters.
Page 49
6 Configure the Local Network Parameter Description Click On to enable the 5GHz wireless function. WLAN (5GHz) Click Off to disable the 5GHz wireless function. Roaming Limit (2.4GHz) The default value is recommended. Roaming Limit (5GHz) The default value is recommended. 3.
Page 50
ZXHN H3601 Maintenance Management Guide Parameter Description Band Width Radio frequency bandwidth, including Auto,20Mhz and 40Mhz. Click On to enable function. Click Off to disable function. Beacon Interval Interval for transmitting beacon frames, default: 100 ms. Beacon frames are used for communicating with other AP devices or network control devices to announce the WLAN presence.
WLAN Advanced provides the parameters of WLAN Advanced configuration features. Steps Access Control-Mode Settings 1. On the main page of the ZXHN H3601, select Local Network > WLAN > WLAN Advanced to the WLAN Advanced page. 2. Click Access Control-Mode Configuration the configuration page, see Figure 6-5.
Page 52
ZXHN H3601 Maintenance Management Guide 3. Configure the access control-mode configuration parameters. Table 6-4 lists the access control-mode configuration parameters. Table 6-4 Access Control-Mode configuration parameters Parameter Description No Filter No filter is to be applied (the default). Black List Deny LAN users to access specific address.
The relevant information of Internet status includes Allocated Address (DHCP), DHCP Server, DHCP Binding and Port Control. Steps Allocated Address(DHCP) 1. On the main page of the ZXHN H3601, select Local Network > LAN > IPv4 to the IPv4 page. 2. Click Allocated Address (DHCP) to the configuration, see Figure 6-7.
Page 54
ZXHN H3601 Maintenance Management Guide Figure 6-8 DHCP Server(IPv4) Page 2. Configure the DHCP server parameters. Table 6-6 lists the DHCP server parameters. Table 6-6 Parameter Descriptions for the DHCP Server Parameter Description DHCP Server Select On to let the device work as a DHCP server and assign IP addresses to open the client PCs or wireless devices.
Page 55
6 Configure the Local Network 1. Click DHCP Binding to the configuration, see Figure 6-9. Figure 6-9 DHCP Binding Page 2. Configure the DHCP Binding parameters. Table 6-7 lists the DHCP binding parameters. Table 6-7 Parameter Descriptions for the DHCP Binding Parameter Description Name...
Before configuring the prefix delegation, make sure that the prefix delegation is enabled for the specified IPv6 WAN connection. Steps Check the allocated address (DHCPv6). 1. On the main page of the ZXHN H3601 device, select Local Network > LAN > IPv4 to open the Allocated Address (DHCP) page, see Figure 6-11.
Page 57
6 Configure the Local Network Figure 6-11 Allocated Address (DHCPv6) Page 2. Click Refresh to refresh the informations. Configure the LAN address. 1. Click LAN Address Management to open the LAN Address Management page, Figure 6-12. Figure 6-12 LAN Address Management Page 2.
Page 58
ZXHN H3601 Maintenance Management Guide 2. Configure the static prefix parameters. Table 6-9 describes the static prefix parameters. Table 6-9 Description of the Static Prefix Parameters Parameter Description Name The name of the prefix. Prefix IPv6 address and prefix length. Only a GUA prefix is supported.
Page 59
6 Configure the Local Network Parameter Description Prefix Delegate Type Option: AutoSense: One prefix selected automatically from all the available prefixes will be delegated. Manual: One or more prefixes selected manually from all the static prefixes configured before will be delegated. Disabled: No prefix will be delegated.
Page 60
ZXHN H3601 Maintenance Management Guide Parameter Description O: other stateful configuration. If On button is selected, the value is 1. If Off button is selected, the value is 0. M = 0 and O = 0: SLAAC is used for acquiring information. It ...
Before configuring routing(IPv4), make sure that the IPv4 WAN connection is created. Steps Routing Table 1. On the main page of the ZXHN H3601, select Local Network > Routing > IPv4 to the Routing(IPv4) page. 2. Click Routing Table to the configuration page, see Figure 6-17.
Page 62
ZXHN H3601 Maintenance Management Guide 1. Click Static Routing to the configuration page, see Figure 6-18. Figure 6-18 Static Routing Page 2. Configure the static routing parameters.Table 6-12 lists the static routing parameters. Table 6-12 Parameter Descriptions for the Static Routing...
Page 63
6 Configure the Local Network Figure 6-19 Policy Routing Page 2. Configure the policy routing parameters. Table 6-13 lists the policy routing parameters. Table 6-13 Parameter Descriptions for the Policy Routing Parameter Description Name The name of Policy routing entry. Egress WAN connection for policy routing Source IP Address...
Before configuring routing(IPv6), make sure that the IPv6 WAN connection is created. Steps Routing Table 1. On the main page of the ZXHN H3601, select Local Network > Routing > IPv6 to the Routing(IPv6) page. 2. Click Routing Table to the configuration page, see Figure 6-20.
Page 65
6 Configure the Local Network 2. Configure the static routing parameters. Table 6-14 lists the static routing parameters. Table 6-14 Parameter Descriptions for the Static Routing Parameter Description Name The name of static routing entry. Egress WAN connection for static routing. Prefix IPv6 address and prefix length.
3. Click Apply button to apply the changes. 6.5 Configure the FTP Server Feature This procedure describes how to enable the feature of the ZXHN H3601 by configuring FTP parameters, including the username and password. Steps 1. In the left navigation tree, click Local Network > FTP. The FTP Application page is...
This page provides the parameters of UPnP configuration features. Steps UPnP 1. On the main page of the ZXHN H3601, select Local Network > UPnP to the UPnP, Figure 6-24. Figure 6-24 UPnP Page Table 6-17 lists the UPnP parameters.
Page 68
Prerequisite The USB device is connected to open the ZXHN H3601 device. Steps 1. On the main page of the ZXHN H3601, select Local Network > DMS/DLNA to open the DMS/DLNA page, see Figure 6-26. Figure 6-26 DMS/DLNA 2.
3. Click Apply button to apply the changes. 6.8 Configure the Samba Service The procedure provides the parameters of samba configuration features. Steps 1. On the main page of the ZXHN H3601, select Local Network > Samba Service to open the Samba Service page, see Figure 6-27.
The relevant information of Internet status includes Domain name, Host Name and DNS. Steps Domain Name 1. On the main page of the ZXHN H3601, select Local Network > DNS to the Domain Name page, see Figure 6-28. Figure 6-28 Domain Name Page 2.
6 Configure the Local Network 6.10 Configure the NetSphere The section describes how to set the device role in the mesh network. Steps 1. In the left navigation tree, click Local Network > NetSphere to the NetSphere page, Figure 6-30. Figure 6-30 NetSphere page 2.
Configure the IPv6 Switch................... 7-16 7.1 Check the Device Status The relevant information of device status is shown as below. Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > Status to the Status page, see Figure 7-1.
7.2 Configure the Account Management This procedure introduces how to manage the user accounts and rights. Steps Guest Account Management 1. On the main page of the ZXHN H3601, select Management&Diagnosis > Account Management to the Admin Account Management page, see Figure 7-2.
Confirmed Password Confirm the new password. 3. Click Apply button to apply the changes. User Account Management 1. On the main page of the ZXHN H3601, select Management > Account Management to the User Account Management page, see Figure 7-3.
7.4.1 Configure the Device Management This procedure introduces how to reboot the device or restore the factory default settings. Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > System Management > Device Management to the Device Management page, see Figure 7-5.
This procedure introduces how to upgrade Software. Prerequisite Before upgrading software, make sure that the upgrade file is ready. Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > System Management > Software Upgrade to the Software Upgrade page, see Figure 7-6.
If the mirror configuration is performed, the packets at the WAN side will be copied to the specified LAN interface, and it can be used for the network analysis and troubleshooting. Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > Mirror Configuration to the Mirror Configuration page, see Figure 7-9.
TR-069 configuration features. The relevant TR-069 includes Basic Configuration and Certificate Management . Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > TR-069 to the TR-069 page. 2. Click Basic Configuration to the TR069 basic configuration page, see Figure 7-10.
Page 80
ACS URL The URL of the automatic configuration server that manages the device. Username/Password User name and password for the ZXHN H3601 to log in to the automatic configuration server. Connection Request URL Connection request URL, which is automatically generated by the system.
Page 81
7 Configure the Management and Diagnosis STUN Configuration 1. Click STUN Configuration to the STUN configuration page, see Figure 7-11. Figure 7-11 STUN Configuration 2. Configure the STUN configuration parameters. Table 7-5 lists the STUN configuration parameters. Table 7-5 Parameter Descriptions for the STUN Configuration Parameter Description Enable...
This procedure introduces how to manage the log. Steps Log Level Management 1. On the main page of the ZXHN H3601, select Management&Diagnosis > Log Management to the Log Management page. 2. Click Log Level Management to the log level management page, see Figure 7-13.
Page 83
7 Configure the Management and Diagnosis Figure 7-14 System Log Management Page 2. Configure the system log management parameters. Table 7-7 lists the system log management parameters. Table 7-7 Parameter Descriptions for the System Log Management Parameter Description Save Log Click On to enable the system log function.
Page 84
ZXHN H3601 Maintenance Management Guide Figure 7-15 Security Log Management Page 2. Configure the security log management parameters. Table 7-8 lists the security log management parameters. Table 7-8 Parameter Descriptions for the security Log Management Parameter Description Save Log Click On to enable the security log function.
The relevant information includes ping diagnosis, trace route diagnosis, DSL line diagnosis and simulation. Steps Ping Diagnosis 1. On the main page of the ZXHN H3601, select Management&Diagnosis > Diagnosis to the Diagnosis page. 2. Click to open Ping Diagnosis page, see Figure 7-17.
Page 86
ZXHN H3601 Maintenance Management Guide Table 7-10 Ping Diagnosis Parameter Descriptions Parameter Description IP Address or Host Name Destination IP address or host name. Egress Data direction. If you want to detect the connection with an external address, select a WAN connection.
7.9 Check the ARP Table The relevant information of table is shown as below. Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > ARP Table to the ARP Table page, see Figure 7-19. Figure 7-19 ARP Table Page 2.
2. Click Refresh button to refresh information. 7.11 Configure the IPv6 Switch This procedure describes how to enable or disable IPv6 support for the ZXHN H3601. Steps 1. On the main page of the ZXHN H3601, select Management&Diagnosis > IPv6...
Chapter 8 Troubleshooting The Power indicator on the front panel is off after the power button is pressed The power switch is off. The power adapter is not correctly connected to the device. Be sure to use the power ...
Need help?
Do you have a question about the ZXHN H3601 and is the answer not in the manual?
Questions and answers
login et mot de pass du repeteur ZXHN H3601P
The default username for the ZTE ZXHN H3601 is "vulladmin". The default password is not specified in the provided context.
This answer is automatically generated