Teknion district Installation Manual
Hide thumbs
Also See for district:
- Installation manual (3 pages) ,
- Installation manuals (5 pages) ,
- Installation manual (6 pages)
Advertisement
Quick Links
district
Section:
Description:
Power Box (UNQPRS- single,UNQPRD-double ), Receptacle (UNQRO)
NOTE: If over Horizontal Tube
configuration is specified. Freestanding
Foot and Power Box CAN NOT
installed on the same side.
A
B1
B3
E
C1
B2
B3
C2
D
For Customer Support please contact
product.support@teknion.com
Date:
DIS_901a
Part and Product Identification
A - Power Box - Double
(UNQPRD) x1
OR
- Power Box - Single
(UNQPRS) x1
B1 - Power Box Mounting Bracket
(MPA25-E078) x1
B2 - Mounting Bracket
(MPA25-E079L/R) x 1pair
B3 - Machine Screw
(FS8-32x0.75QR2) x 4
C1 - Hex Flange Locking Bolt
(FN5-16-18x2HB) x2
C2 - Lock Nut
(FN5-16-18HB) x2
C3 - #8X1/2RND,ROB,Zinc,Type B
(FS8-1/2RRB) x2
D - Power/Data Bezel -Double
(PB02-E095) x1 -Single Sided
OR
Power/Data Bezel -Single
(PB02-E096) x1 -Single Sided
E - Receptacle( Ordered separately )
(UNQRO) x2 -Single Sided
x4 -Double Sided
WARNING!
Do not connect to power source until installation is complete.
Connection to the building power source must be performed
by a licensed electrician.
Not following these instruction could result in damage and/
or injury.
It is recommended that electrical connections be made under
the supervision of a licensed electrician in accordance with
applicable codes and regulations.
Dec 2015
Page No:
1 of 11
Rev. No: 3
x2 -Double Sided
x2 -Double Sided
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Teknion district
Summary of Contents for Teknion district
- Page 1 Section: Date: Dec 2015 Page No: 1 of 11 Description: DIS_901a Rev. No: 3 Power Box (UNQPRS- single,UNQPRD-double ), Receptacle (UNQRO) Part and Product Identification A - Power Box - Double (UNQPRD) x1 - Power Box - Single (UNQPRS) x1...
- Page 2 Section: Date: Dec 2015 Page No: 2 of 11 Description: DIS_901a DOUBLE BOX - ALL PANEL WALL WIDTHS Over Horizontal Tube Under Horizontal Tube Right and Left side location. NOTE: Power Box has to be positioned with arrows facing up in both optional locations: above and below Horizontal tube.
- Page 3 Section: Date: Dec 2015 Page No: 3 of 11 Description: DIS_901a SINGLE BOX - 24" WIDE PANEL WALL Over Horizontal Tube Under Horizontal Tube Center location on Panel Wall ONLY. WARNING! *Do not connect to power source until installation is complete. *Connection to the building power source must be performed by a licensed electrician.
- Page 4 Section: Date: Dec 2015 Page No: 4 of 11 Description: DIS_901a SINGLE BOX - 30" & 36" WIDE PANEL WALL Over Horizontal Tube Under Horizontal Tube Center location ONLY. WARNING! *Do not connect to power source until installation is complete. *Connection to the building power source must be performed by a licensed electrician.
- Page 5 Section: Date: Dec 2015 Page No: 5 of 11 Description: DIS_901a SINGLE BOX - 39" - 96" WIDE PANEL WALLS Over Horizontal Tube Under Horizontal Tube Right sided or Left sided locations. (Left side shown). Mirror assembly according to the side.
- Page 6 Section: Date: Dec 2015 Page No: 6 of 11 Description: DIS_901a "L" MOUNTING BRACKETS INSTALLATION SECURING IN PLACE STEP 2: Fasten with machine screws included with Bracket Kit. STEP 1: Insert Locking Bolt into "L" Brackets. Line up holes of "L" Brackets with applicable holes on Mounting Bracket.
- Page 7 Section: Date: Dec 2015 Page No: 7 of 11 Description: DIS_901a INSTALLING POWER BOX ON HORIZONTAL TUBE DETAIL NOTE: If over Horizontal Tube configuration is specified. Freestanding Foot and Power Box CAN NOT installed on the same side. 5.3"...
- Page 8 Section: Date: Dec 2015 Page No: 8 of 11 Description: DIS_901a INSERTING RECEPTACLES INSTALLING FASCIA AND POWER/DATA BEZEL STEP 6: Push Receptacles with arrows facing up in place with as shown. SECURE WITH SCREWS STEP 7: Fasten to Power Bracket with Machine Screws included with Locking Bolts Kit. If STEP 8: After all necessary connection are finished (Harness, Base Feed or Ceiling Feed) install Double Sided Power Box is specified, continue on the other side, repeating steps 6 and 7.
- Page 9 Section: Date: Dec 2015 Page No: 9 of 11 Description: DIS_901a "L" - BRACKETS INSTALLATION SECURING WITH SCREWS STEP 1: Line up holes of Mounting Bracket with holes of "L" Bracket. Use guide on page 2 of STEP 2: Fasten wit machine screw s included with Bracket Kit.
- Page 10 Section: Date: Dec 2015 Page No: 10 of 11 Description: DIS_901a INSTALLING UNDER HORIZONTAL TUBE DETAIL 2 5.3" 4.5" STEP 5: Insert Locking Bolts and install Power Box assembly under horizontal tube, securing The distance between face of Panel Wall vertical tube has to be 5.3" for both Single and Double in place by Lock Nuts.
- Page 11 Section: Date: Dec 2015 Page No: 11 of 11 Description: DIS_901a INSERT RECEPTACLES ON POWER BOX FASCIA AND BEZEL INSTALLATION STEP 6: Push Receptacles with arrows facing up in place with as shown. SECURING STEP 7: Fasten to Power Bracket with Machine Screws included with Locking Bolts Kit. If STEP 8: After all necessary connection are done (Harness, Base Feed, Ceiling Feed), install Double Sided Power Box is specified, continue on the other side, repeating steps 6 and 7.
Need help?
Do you have a question about the district and is the answer not in the manual?
Questions and answers