Dräger X-zone 5000 Instructions For Use Manual page 39

5. Insert the X-am 5000/
5600 into the device
receptacle.
NOTICE
i i
The clip on the X-am 5000/5600 must be closed.
6. Place the holder onto the housing.
NOTICE
i
i
The seal areas of the holder must be clean and dry.
Clean and dry seals if necessary.
7. Fasten the lock at the holder.
8. Press the key on the X-zone 5000 and hold it for approx.
3 seconds.
The battery LED will be green, red/green or red (see
chapter 19 on page 63) depending on the battery capacity.
The X-zone 5000 is in STANDBY mode.
CAUTION
!
All 3 locks must be pulled tight to ensure that the X-am
5000/5600 is in the correct position and the charger
connection is assured.
NOTICE
i i
The X-zone 5000 automatically switches from
STANDBY mode to OFF mode if the device is not
switched to On mode within 72 h.
3.1.2 ON mode
CAUTION
!
When switching
recommends wearing hearing protection or using the
alarm-attenuation ring (order no. 83 20 110) as the
acoustic alarm is activated for a brief period.
Switch on the X-am 5000/5600 following the instructions

for use.
The visual and the audible alarm will be activated for a

short time.
The X-am 5000/5600 switches to X-zone mode (see

chapter 3.1.3 on page 39).
The visual and acoustic life signal (green LED ring and

single tone) is issued depending on the configuration
(1 – 60 seconds; default setting: 2 seconds).
The X-zone 5000 is in ON mode and ready for operation.

Dräger X-zone 5000
on the X-zone 5000,
In ON mode, the alarm signals of the X-am 5000/5600 are

evaluated, processed, and, if applicable, transmitted to
other X-zone 5000 devices.
3.1.3 X-zone mode:
The battery symbol

by the X-zone mode symbol
The X-am 5000/5600 is supplied via the X-zone 5000

battery.
If the activated X-am 5000/5600 is removed from the

X-zone 5000, the device will exit X-zone mode after max.
00533112.eps
10 seconds.
3.1.4 X-am 5000/5600 Info mode
In measuring mode, press the

5600 for approx. 3 seconds.
Press the

OK
peak values and the exposition values TWA and STEV as
well as additional X-zone information will be displayed.
If there are warnings or faults, the corresponding notes or
error codes (e. g. 01) are displayed (see chapter 11.1 on
page 59).
Info window X-am 5000/5600:
1 Station number in grouping mode:
The station number identifies a group device uniquely
within a group.
2 Wireless status: ON/OFF:
Displays whether the wireless function of the X-zone 5000
is switched on or off.
The wireless function can be switched on and off using the
Dräger CC-Vision PC software (see chapter 10 on
page 56).
Dräger
3 Network number:
If independent wireless networks are required, different
network numbers must be assigned (see chapter 4 on
page 42).
The network number can be set using the Dräger CC-
Vision PC software (see chapter 10 on page 56).
4 Group ID:
The group ID uniquely identifies a group (only the last
4 characters of the group ID are displayed).
5 X-zone mode symbol
Displays whether or not there is a connection between the
X-zone 5000 and the X-am 5000/5600.
If no key is pressed for 10 seconds, the X-am 5000/5600

returns automatically to the measuring mode.
on the X-am 5000/5600 is replaced
on the X-zone 5000.
key on the X-am 5000/
OK
key in succession for the next display. The
1
--
2 RF: ON
3 NET: 005
4
P\N: FFFF
5
Operation
02533112.eps
39