AIR-EAGLE
900MHz 20 Dry Contact Input Transmitter
MODEL 441-12000-120VAC
DESCRIPTION
The A
-E
XLT PLUS, M
IR
AGLE
ODEL
a dry contact input transmitter designed to send up to twenty
IS
independent commands to an Air-Eagle Receiver(s) that can be located
up to 2500 feet away. Any number of transmitters and receivers can be
combined to create a system. The Air-Eagle XLT TX is user-
programmable for up to eight network frequencies to allow multiple
systems to operate simultaneously in the same area. Utilizing spread-
spectrum technology this unit provides the utmost security and reliability
even in the noisiest RF environments.
DISCONNECT Power from all equipment before installation.
1.
Mount the A
-E
XLT T
IR
AGLE
2.
Install wiring to contact input terminal strip
3.
Make desired frequency and repeater mode selections using
instructions on page 2.
4.
Install antenna onto connector located on the top on the enclosure.
5.
Connect supplied power input cable to your external power source.
FREQUENCY & REPEATER MODE SET-UP
The unit is shipped from the factory with the SEL1 switches in the open
positions. By default, it is operating on Frequency #1 and the command
transmitted will not be repeated by the receivers. If you wish to transmit on
a different frequency, and/or set the unit to transmit a repeating packet,
follow the instructions on the table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired frequency and/or repeater mode using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
REPEATER MODE
SEL1
SWITCH
OPEN
NUMBER
SW4
Repeater Mode OFF
FREQUENCY SET-UP
Network
SW5
Frequency
1
(default)
OPEN
2
CLOSED
3
OPEN
4
CLOSED
5
OPEN
6
CLOSED
7
OPEN
8
CLOSED
Note – Switches 1 thru 3 are not used on this model – leave OPEN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
®
XLT
441-12000-120VAC RF T
RANSMITTER
in a convenient location.
RANSMITTER
CLOSED
(default)
Repeater Mode ON
SW6
SW7
OPEN
OPEN
OPEN
OPEN
CLOSED
OPEN
CLOSED
OPEN
OPEN
CLOSED
OPEN
CLOSED
CLOSED
CLOSED
CLOSED
CLOSED
PRODUCT INFORMATION
BULLETIN
Dimensions 8" L x 6" W x 4" H
TERMINAL STRIP WIRING
BOTTOM TERMINAL BLOCK
1
C Input #1
2
N/O Input #1
3
C Input #2
4
N/O Input #2
5
C Input #3
6
N/O Input #3
7
C Input #4
8
N/O Input #4
9
C Input #5
10
N/O Input #5
TOP TERMINAL BLOCK
1
C Input #11
2
N/O Input #11
3
C Input #12
4
N/O Input #12
5
C Input #13
6
N/O Input #13
7
C Input #14
8
N/O Input #14
9
C Input #15
10
N/O Input #15
AC INPUT TERMINAL BLOCK
1
120 VAC Neutral
11
C Input #6
12
N/O Input #6
13
C Input #7
14
N/O Input #7
15
C Input #8
16
N/O Input #8
17
C Input #9
18
N/O Input #9
19
C Input #10
20
N/O Input #10
11
C Input #16
12
N/O Input #16
13
C Input #17
14
N/O Input #17
15
C Input #18
16
N/O Input #18
17
C Input #19
18
N/O Input #19
19
C Input #20
20
N/O Input #20
2
120 VAC Hot