1. Manuals
  2. Brands
  3. BWI Eagle Manuals
  4. Transmitter
  5. AIR-EAGLE XLT
  6. Manual

BWI Eagle AIR-EAGLE XLT Manual

900 mhz rf transmitter
Hide thumbs Also See for AIR-EAGLE XLT:
Table of Contents

Advertisement

Quick Links

Download this manual
AIR-EAGLE XLT
441-HH-2
900 MHz RF Transmitter
Document Date: 9/29/2022
Product Rev: 12

Advertisement

Table of Contents
loading

Related Manuals for BWI Eagle AIR-EAGLE XLT

Summary of Contents for BWI Eagle AIR-EAGLE XLT

  • Page 1 AIR-EAGLE XLT 441-HH-2 900 MHz RF Transmitter Document Date: 9/29/2022 Product Rev: 12...

  • Page 2: Warranty Statement

    441-HH-2 WARRANTY STATEMENT BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to include the repair or replacement of defective equipment. This warranty does not cover damage due to external causes, including accident, problems with electrical power, usage not in accordance with product instructions, misuse, neglect, alteration, repair, improper installation, or improper testing.

  • Page 3: Controls And Indicators

    441-HH-2 INTRODUCTION The Air-Eagle XLT TX is a handheld R.F. transmitter capable of sending up to two unique digital commands to an Air-Eagle XLT Receiver located up to 2500 feet away. Any number of transmitters and receivers can be combined to create a medium-range radio frequency system that operates hazardous or hard-to-reach equipment from safe, convenient locations.

  • Page 4: Frequency Programming

    441-HH-2 FREQUENCY PROGRAMMING Read instructions completely before beginning programming procedure. Transmitters are shipped from the factory set to Frequency 1 by default. The frequency can be changed at any time by following the procedure below. Once changed, it is recommended to label the transmitter with the selected frequency number.

  • Page 5: Relay Programming

    441-HH-2 RELAY PROGRAMMING Read instructions completely before beginning programming procedure. Transmitters are shipped from the factory set to operate relays 1 and 2 in the remote receiver by default. The relays to be operated can be changed at any time by following the procedure below. Once changed, it is recommended to label the transmitter with the selected relay numbers.
  • Page 6 441-HH-2 RELAY PROGRAMMING (continued) 5. Release Button 1, then quickly press it the number of times equal to the desired relay setting. For example, press it 4 times to select Relays 7 and 8. See chart below. Relay Setting Transmitter is Operating Receiver Relays: Relay 1 and Relay 2 Relay 3 and Relay 4 Relay 5 and Relay 6...

  • Page 7: Transmitting Mode

    441-HH-2 TRANSMITTING MODE Read instructions completely before beginning programming procedure. The transmitter can be set to be in a standard transmitting mode or in a repeater mode where all receivers will repeat the transmission. *Note: When setting up the Transmitting Mode, the TX LED will cycle through all other set up options (Frequency, Relay) before it gets to the transmitting mode setting.

  • Page 8: Specifications

    441-HH-2 SPECIFICATIONS Durable Sealed Membrane Keypad – Eliminates Dust, Dirt and Keypad Moisture Failures Enclosure ABS UL94 HB Enclosure with ring is rated IP54 (Not Waterproof) Protective Ring SEBS (TPE) Power Requirements 3.0 VDC (2) 1.5V lithium each, size AAA, to equal 3.0VDC nominal. For Battery Type best performance use only Energizer Brand Lithium Batteries.

This manual is also suitable for:

441-hh-2

Table of Contents