HP Kayak XU04 Installation Manual
Installing accessories in your hp pc workstation
Hide thumbs
Also See for Kayak XU04:
- Supplementary manual (74 pages) ,
- User manual (66 pages) ,
- Installation and configuration manual (30 pages)
Related Manuals for HP Kayak XU04
Summary of Contents for HP Kayak XU04
- Page 1 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Explains in detail how to install accessories, such as extra memory, accessory boards, and additional disk drives.
-
Page 2: Supported Hp Accessories
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Supported HP Accessories Supported HP Accessories Internal Mass Storage Devices 5 Pairs of Rails for Front Access Devices: - 3.5-inch disk drive rails - 5.25-inch disk drive rails... -
Page 3: Removing And Replacing The Cover
5 Grasp the cover on the sides at the back of the computer and slide it forwards and off the computer. HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Removing and Replacing the Cover English... - Page 4 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Removing and Replacing the Cover Replacing the Cover 1 Ensure that you have installed all your accessories and that all internal cables are properly connected and safely routed.
- Page 5 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Removing and Replacing the UltraFlow Airflow Guide 1 Press the retaining buttons on each side of the airflow guide and lift it partly out of the PC Workstation’s case.
-
Page 6: Installing Memory
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Memory Installing Memory Main Memory Modules If you need more main memory, you can install up to 2 GB of memory in four DIMM slots. For details of supported memory, refer to "Supported HP Accessories", on page 2. - Page 7 Replace the cover (refer to page 4) and the airflow guide (refer to page 5). 10 Check the HP Summary Screen to verify the new configuration. HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Memory Memory module...
-
Page 8: Installing Mass Storage Devices
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Installing Mass Storage Devices Connecting Devices If you add an IDE Zip drive, hard disk drive, CD-ROM drive, CD-RW drive, or tape drive, you need to connect it to power and data cables. - Page 9 Depending on your operating system, you may need to set a SCSI ID for Plug and Play devices (SCSI devices that support the SCAM protocol). If HP FastRAID is installed, you will need to set a SCSI ID. You should assign an unused SCSI ID to the second SCSI hard disk drive (for example, SCSI ID 1).
-
Page 10: Installing A Hard Disk Drive In An Internal Shelf
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Installing a Hard Disk Drive in an Internal Shelf CAUTION Hard disk drives larger than one inch (1”) in height can only be housed in the lower internal shelf. - Page 11 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation 5 Secure the drive with the four self-retaining screws. 6 Locate the appropriate data cable for the hard disk drive (refer to page 8). 7 Connect the power cable and the data cable to the rear of the drive.
-
Page 12: Installing A Hard Disk Drive In A Front-Access Shelf
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Installing a Hard Disk Drive in a Front-Access Shelf NOTE To ensure your hard disk drive is properly located and cooled, you should only install drives that are up to one inch (1”) in height and of a speed equal to or less than 7200 rpm in this shelf. - Page 13 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation 6 Slide the drive tray into the drive shelf and secure it. 7 Locate the appropriate data cable for the disk drive (refer to page 8). To improve access, you may need to disconnect any devices already connected to the SCSI cable and allow the cable to hang outside the of the PC Workstation’s case.
-
Page 14: Completing The Installation Of A Hard Disk Drive
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Completing the Installation of a Hard Disk Drive When a SCSI Hard For more information on completing the installation of a SCSI hard disk drive, refer to the SCSI Administrator’s Guide available on HP’s web... - Page 15 To improve access, you may need to disconnect any devices already connected to the SCSI cable and allow the cable to hang outside the of the PC Workstation’s case. HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Mounting Rails Secure the drive...
- Page 16 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices 8 Connect the data and power cables to the rear of the device. (The connectors are shaped to go in one way only.)
- Page 17 2 In the Setup program, select the Advanced menu, the Flexible Disk Drives submenu, and check that the drive has been detected. 3 Press HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation to save and exit the program. to save and exit the program.
-
Page 18: Installing Accessory Boards
HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Accessory Boards Installing Accessory Boards CAUTION Static electricity can damage electronic components. Turn OFF all equipment. Don’t let your clothes touch the accessory. To equalize the static electricity, rest the accessory bag on top of the computer while you are removing the accessory from the bag. - Page 19 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation 4 Unscrew and remove the slot cover. Store it in a safe place. If the slot cover is tight, loosen the screws on the adjacent slots. Unscrew and remove the slot cover 5 Hold the board horizontally by its “top”...
- Page 20 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing Accessory Boards 6 Align the board’s connector with the slot’s socket. Firmly press the board into the socket. Ensure the board’s connector engages completely with the socket and does not touch components on other boards.
-
Page 21: Installing A Processor
3 If installing a second processor, remove the HP UltraFlow airflow guide (refer to page 5). 4 Remove the metal retaining plate that secures the processor(s) by releasing the four self-retaining screws. HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing a Processor English... - Page 22 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing a Processor 5 The system board has two processor sockets. a If you are changing the existing (boot) processor, remove it from b If you are installing a second (dual) processor, remove the...
- Page 23 NOTE To fully benefit from dual processing, you will need to re-install Windows NT 4.0 on your PC Workstation. HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation UP=OFF DOWN=ON Switch 3...
- Page 24 HP Kayak XU PC Workstation — Installing Accessories In Your HP PC Workstation Installing a Processor English...