Thermo Scientific iCAP 7000 Series Hardware Installation
Icp-oes spectrometer
Hide thumbs
Also See for iCAP 7000 Series:
- Manual (72 pages) ,
- Manual (36 pages) ,
- Reference manual (45 pages)
Table of Contents
Advertisement
Quick Links
iCAP 7000 Series ICP-OES Spectrometer
iCAP 7000 Series ICP
Hardware Installation Procedure
Hardware
This is section 1 (of 3) for part number 8423 460 10030
This is section 1 (of 3) for part number 8423 460 10030
This is section 1 (of 3) for part number 8423 460 10030
©
2013 Thermo Fisher Scientific Registration No. 441506
Thermo Fisher Scientific Registration No. 441506
SOLAAR House, 19 Mercers Row, Cambridge CB5 8BZ,
19 Mercers Row, Cambridge CB5 8BZ,
United Kingdom. Telephone +44 (0) 1223 347400, Fax +44 (0)
United Kingdom. Telephone +44 (0) 1223 347400, Fax +44 (0)
1223 347402,
www.thermoscientific.com
OES Spectrometer
Installation Procedure
Advertisement
Table of Contents
Related Manuals for Thermo Scientific iCAP 7000 Series
Summary of Contents for Thermo Scientific iCAP 7000 Series
-
Page 1: Icap 7000 Series Icp-Oes Spectrometer
7000 Series ICP iCAP 7000 Series ICP-OES Spectrometer OES Spectrometer Hardware Hardware Installation Procedure Installation Procedure This is section 1 (of 3) for part number 8423 460 10030 This is section 1 (of 3) for part number 8423 460 10030 This is section 1 (of 3) for part number 8423 460 10030 ©... -
Page 2: Table Of Contents
Connection of Coolant ....................8 2.10.1 Install water chiller ..................... 8 Setting the Cetac Personality for all iCAP 7000 Series ............. 9 iCAP 7600 Sprint Valve installation guide ................ 10 Installing Software ......................11 Additional Schematics Detailing the Plumbing Options for the iCAP 7600 Valve... 12... -
Page 3: Introduction
7000 Series ICP-OES Spectrometer Installation Details Introduction Detailed below is the installation procedure for the spectrometer. It is very important that these procedures are followed, in correct order and taking account of the time delays required. Failure to do so can result in extended installation and possible damage. The procedures and delays are designed to prevent problems with purge, software, firmware and hardware. -
Page 4: Installation Flow Diagram
7000 Series ICP-OES Spectrometer Installation Details 1.1 Installation Flow Diagram Shipment moved to customer laboratory Site guide conformation 15 minutes Unpack shipment 60 minutes Locate equipment on bench 60 minutes Check packing list 15 minutes Connect equipment and start purge... -
Page 5: Installation
7000 Series ICP-OES Spectrometer Installation Details Installation Pre-Installation Requirements Ensure that the requirements detailed in the Pre-Installation checklist are provided in the location chosen by the user. Read each section of the site Pre-Installation guide to verify site, gas, chiller, extraction and waste requirements are met or set during the installation process. -
Page 6: Locate Instrument
7000 Series ICP-OES Spectrometer Installation Details supplied with the equipment. 2.4 Locate Instrument Once the site requirements are confirmed as acceptable, prepare to install the instrumentation. 2.4.1 Position iCAP Lift spectrometer on to the bench (using 4 people to lift). -
Page 7: Spectrometer Power-Up
7000 Series ICP-OES Spectrometer Installation Details Be sure to orientate the filter correctly, using the arrow marking the direction of gas flow. Make sure the customer is aware that they must check the gas filters periodically. Set the argon pressure gauge to 80psi/ 5.5bar*, the nitrogen purge pressure to 45psi/ 3.0bar to 80psi/5.5bar (if used) and the additional gas (7600 only) to 30psi/2.0 bar (if used). -
Page 8: Connection Of Coolant
7000 Series ICP-OES Spectrometer Installation Details 2.10 Connection of Coolant 2.10.1 Install water chiller ♦ Follow the instructions supplied with the chiller. ♦ Connect up the water chiller to the push-fit ports on right hand side of instrument (taking care to connect... -
Page 9: Setting The Cetac Personality For All Icap 7000 Series
7000 Series ICP-OES Spectrometer Installation Details Setting the Cetac Personality for all iCAP 7000 Series Follow the unpacking and assembly instructions for the autosampler. Connect the serial cable between the PC and the autosampler and the power supply to the autosampler: NOTE: It’s imperative that the Cetac Autosampler firmware Personality is configured for the... -
Page 10: Icap 7600 Sprint Valve Installation Guide
7000 Series ICP-OES Spectrometer Installation Details 4. iCAP 7600 Sprint Valve installation guide Note: This section only applies to iCAP 7600 systems: Connect the serial cable between the iCAP and the autosampler, and the power supply to the autosampler:... -
Page 11: Installing Software
7000 Series ICP-OES Spectrometer Installation Details Installing Software For Qtegra ISDS see Installation part 2 of 3 Page 11 of 14 Version 4301 460 00632... -
Page 12: Additional Schematics Detailing The Plumbing Options For The Icap 7600 Valve
7000 Series ICP-OES Spectrometer Installation Details 6. Additional Schematics Detailing the Plumbing Options for the iCAP 7600 Valve. Standard configuration for loading a sample into the sample loop. Standard configuration for the injection of the sample from the sample loop. - Page 13 7000 Series ICP-OES Spectrometer Installation Details Configuration for loading a sample into the sample loop with an additional standard. Configuration for the injection of the sample from the sample loop with an internal standard. Page 13 of 14 Version 4301 460 00632...
- Page 14 7000 Series ICP-OES Spectrometer Installation Details Valve configuration for Manual Sampling. Page 14 of 14 Version 4301 460 00632...