Description Of Main Parts; Intended Use; Functional Description - BorMann PRO BBP4015 Manual

EN
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 5 °C - 45 °C. Let a hot battery cartridge cool down before charging it.
4. Charge the battery cartridge if you do not use it for a long period (more than six months).

Description of main parts

1. Nozzle
2. Spray Pipe
3. Chemical Tank Lid
4. Spray Pipe Holder
5. Chemical Tank
6. Lever Cock
7. Cover
8. Water Hose
9. Power Switch
* Not included with all models.

Intended use

This tool is intended for spraying agricultural and horticultural chemicals for pest and weed control.

Functional description

Caution: Always be sure that the tool is switched off and the battery cartridge is
removed before adjusting or checking function on the tool.
Installing or removing battery cartridge
1. To install the battery cartridge, open the cover while pushing the plastic buckle. Align the tongue
on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until
it locks in place with a little click. After installing or removing the battery cartridges, be sure to close
the cover.
Fig.1
1. Cover
2. Plastic buckle
2. To remove the battery cartridges, Slide the battery cartridge while pressing the button on the
front of the cartridge.
Fig.2
1. Button
2. Battery cartridge
Tool/Battery protection system
The tool is equipped with a battery protection system. This system automatically cuts off power to the
motor to extend battery life. The tool will automatically stop during operation if the tool and/or battery
are placed under one of the following conditions:
Overload protection: The tool is operated in a manner that causes it to draw an abnormally high
current. In this situation, turn the tool off and stop the application that caused the tool to become
overloaded. Then turn the tool on to restart. If the tool does not start, the battery is overheated. In
this situation, let the battery cool before turning the tool on again.
Overheat protection: When the tool/battery is overheated, the tool stops automatically. In this situa-
tion, let the tool/battery cool before turning the tool on again.
Over-discharge protection: The remaining battery capacity is too low and the tool will not operate. In
this situation, remove and recharge the battery.
9
10. Button Of Battery Cartridge
11. Battery Cartridge*
12. Battery Cartridge Cover
13. Plastic buckle
14. Bolt
15. Back Cushion
16. Back Strap
17. Various nozzles A
WWW.BORMANNTOOLS.COM
* The manufacturer reserves the right to make minor changes to product design and technical specifi-
cations without prior notice unless these changes significantly affect the performance and safety of the
products. The parts described / illustrated in the pages of the manual that you hold in your hands may also
concern other models of the manufacturer's product line with similar features and may not be included
in the product you just acquired.
* Please note that our equipment has not been designed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses
or for equivalent purposes.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair
or replacement work, including maintenance and special adjustments, must only be carried out by tech-
nicians of the authorized service department of the manufacturer.
CAUTION: Always switch off the tool before in-
stalling or removing of the battery cartridge.
CAUTION: Hold the tool and the battery cartridge
firmly when installing or removing battery car-
tridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your
hands and result in damage to the tool and bat-
tery cartridge and a personal injury.
CAUTION: Always install the battery cartridge ful-
ly. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge for-
cibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION: Be sure to lock the cover before oper-
ating.
CAUTION: For more information regarding the
operation of the battery and charger please refer
to the instructions manual of the battery charger.
Make sure to read all the instructions before us-
ing this device.