Table of Contents
Advertisement
LE4020/LE4020CF Installation Manual
product identifier that has the format. US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of
0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment LE4020/LE4020CF causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this
happens the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment for repair or warranty information, please contact the facility indicated below. If the equipment is causing
harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is of
a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 2600 West Pointe Dr.., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation
commission for information. Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able
to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling
equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same
telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your
telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.
ISED Compliance Statement
This Equipment meets the applicable Industrial, Scientific and Economic Development (ISED) Terminal Equipment Technical Specifications. This is
confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration
of Conformity indicating that ISED Canada technical specifications were met. It does not imply that that ISED Canada approved the equipment. The
Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed 5.
IC:160A-LE4020
Cet équipement est conforme aux spécifications techniques applicables aux équipements terminaux d'ISED Canada. Ceci est confirmé par le numéro
d'enregistrement. L'abréviation IC précédant le numéro d'enregistrement signifie que l'enregistrement a été effectué sur la base de la Déclaration de
conformité indiquant que le produit est conforme aux spécifications techniques d'ISED Canada. Ceci n'implique pas que le produit ait été approuvé par
Industrie Canada.
Le nombre équivalent de sonneries (REN) de cet appareil terminal est 0.0. Le REN attribué à chaque équipement terminal fournit une indication sur le
nombre maximum de terminaux pouvant être connectés sur une interface téléphonique. La terminaison sur une interface peut constituer en n'importe quelle
combinaison d'appareils, à la condition seulement que la somme des Nombres équivalents de sonneries de tous les appareils ne soit pas supérieure à 5.
This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B
respecte toutes les exigences de règlement sur le matériel brouilleur du Canada.
CAN ICES-3 (B) / NMB-3 (B)
The term "IC:" before the radio certification number only signifies that ISED Canada technical specifications were met.
NIST Validation of encryption algorithm AES128 certificate No. C187.
NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER
INVOLVED PARTIES
This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and
Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to the specific values or not used at all as indicated
below.
Program Feature or Option Permitted in UL 864 (Y/N?) Possible Settings
Supervision
Yes
Inputs/Outputs
Yes
SMS Remote Control
No
Settings Permitted in UL 864
5 minutes /60 minutes 5 minutes (see note below)
Fire/Burg signals
Fire related signals only
Enable/Disable
Disable
34
Advertisement
Table of Contents
