Table of Contents
Advertisement
9.1
Enrollment (teaching) of wireless items
The control panel equipped with a radio module can enroll up
to 32 wireless detectors (2 in each zone), up to 8 controllers
(remote controls & keypads), wireless sirens and an additional
JA-6x control panel as subsystem:
Press key 1 (while „P" is displayed) to enter the
enrolling mode. The control panel will display the next
free position to enroll a detector.
o
If no JA-60E keypad is used in the installation and
you need to enroll a wireless JA-60F keypad:
connect (short ) the RESET pins on the control
panel board it will open the learning mode
(tamper in the control panel must remain
opened)
install batteries to the JA-60F keypad and wait
until the keypad enrolls. Enrollment will be
confirmed on the keypad.
disconnect the RESET pins and then use the
keypad to enroll all the other items in following
way
Use key 1 and 7 to scroll (up and down) all control panel
wireless positions – 1 to 16 (detectors) – c1 to c8
(controllers & keypads) – A (wireless siren) – J (sub control
panel JA-6x). The display shows the position number while
the Battery LED indicates if the position is occupied. The
system will not allow enrollment of an item into a non-
corresponding position (a detector can not be enrolled into
a controller position etc.).
Detectors and keypads are enrolled after their power is
switched on (batteries are installed). A remote control is
enrolled after both of its buttons are simultaneously
pressed and held for 3 seconds. A subsystem control panel
will enroll after sequence 299 is entered while it is in its
programming mode.
Control panel confirms enrollment with a „beep" (press
F to get confirmation by a wired siren). The display will
show the number of the enrolled item for 2 seconds and
then it will display the next free position.
Second detector enrolment to a zone – select the zone
into which you want enroll the second detector. Press shortly
key 5 (selects second position) and then install battery to the
detector. Enrollment of the second detector will be indicated
by the Fault LED. If there are two detectors in a zone, all
indicators in this zone (alarm, tampering, low battery etc.) will
be common for both enrolled detectors (for example, if any
of the two detectors is tampered with, the zone will indicate
tampering.).
To change the position of an enrolled item - simply
enroll it to the new selected position (the item will „move").
If you enroll an item to an occupied position, the former
item will be deleted and only the new enrollment is valid.
Normally only one item (detector, controller etc.) can be
stored to each position.
Erase an enrolled item
position and then press and hold key 2 for two seconds. The
item will be erased (confirmed with a long beep). If you press
and hold key 3, all enrolled controllers (remote controls and
keypads) will be erased. Pressing and holding key 4 will erase
all enrolled items (detectors, controllers, siren and the sub
system). If two detectors were enrolled in a zone, both of them
will be erased if you erase the zone's position.
The JA-60A wireless siren will enroll (to position A) when
its power is switched on. If you need to enroll a siren which
is already powered and it is not possible to easily switch off
its power, you can enroll it the following way: enter the
enrolling mode and then enter the 6 digit siren production
code (printed in the siren's manual). The control panel will
"request" the siren to enroll. The siren will do that only if it
JA-63 „PROFI" Alarm System
enter: 1
by selecting the corresponding
has no current communication with any other control panel
(This protects you from enrolling your neighbor's siren).
Multiple outdoor sirens or multiple subsystems
enrolment – enter 000000 while in enrolling mode. After
this outdoor sirens and JA-6x subsystems can be enrolled
to positions 1 to 16 (position A and/or J must be used first).
By pressing the button 8 in the enrolment mode the
communication quality of the items can be checked
(LED indicator "battery" will start flashing). After receiving
signal from the item the level of the signal is shown on the
display from 0 to 10 (corresponding to 0-100% in the
ComLink software). In this mode it is also possible to adjust
level of audible indications by pressing the button F and
scroll positions of the enrolled items by pressing buttons 1
and 7. Button N exits checking mode.
To exit the enrolling mode press the N key
Note: if an item was not enrolled after its batteries were
installed, it is because the control panel recognized its radio
signal as a weak one. Items are only enrolled if their radio signal
has a level which guarantees reliable communication. Check the
detector's batteries and try to enroll the problematic sensor once
more. If it is not accepted by the control panel, you should
change the location of the item. All items should be located 1
meter as minimum from the control panel.
9.2
Hard-wired zone input setting
If the hard wired L1 to L4 zones are used, their features can be
programmed by entering:
where:
nn
zone number: 01 to 16
x
input triggering: 0 = off, 1 = Normally Closed, 2 = balanced
loop (EOL resistor 2k2), 3 = double balanced loop (EOL
resistors 2x 2k2)
y
reaction: 0 = Instant, 1 = Delay, 2 = Fire, 3 = Panic, 4 =
Tamper, 5 = Next delay, 6 = Arming control
s
address to section, 1 = A, 2 = B, 3 = C (shared common
section, which is armed only if both A and B sections are
armed). If the control panel is not split, select s=1; if you
select s=2 then this zone will be automatically bypassed
within partial arming. For details about splitting see section
9.23.
Notes:
If you will not use a particular input, you can switch it off
completely with parameter x = 0
Next delay input (y=5) provides entrance delay only if at the
moment of its triggering the entrance delay has been in
progress (activated before by any delayed input). If no
delayed input is triggered before next delayed, the triggering
will cause an instant alarm.
Addressing of inputs to section C when the control panel is
not split has the same effect as addressing to section B (i.e.
automatic bypass while partial arming is used).
If y=6 is programmed, then each triggering of this input
changes arming status (arm – disarm – arm...) of the entire
system or just the corresponding section if the system is
split.
Example: to set zone 2 input as a balanced loop with an
instant reaction, addressed to section A, enter: 60 02 201
Factory default setting: L1 = delay, L2 = next delay, L3 =
instant, L4 = tamper
- 9 -
sequence: 60 nn xys
60 nn xys
MGK55402
Advertisement
Table of Contents
