Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GLP 7687
Summary of Contents for GLP 7687
- Page 1 Luminaire software version 118 Hardware version 10074xxxxx or higher...
- Page 2 This manual covers firmware version 118 and hardware version 10074xxxxx or higher © 2017-2019 German Light Products GmbH. All rights reserved. The marks ‘GLP’ and ‘German Light Products’ are trademarks registered as the property of German Light Products GmbH in Germany, in the United States of America and in other countries.
-
Page 3: Table Of Contents
Contents Safety ..................4 Avoiding damage ..............9 Product overview ..............10 Product features ..............11 Preparing for use..............15 Control menus and LCD display ..........21 Control menu layout ............... 22 DMX channel layout ............... 27 Service and maintenance ............. 30 Technical specifications ............ -
Page 4: Safety
• Check the GLP website at www.glp.de and make sure that you have the latest version of this user manual. Check also that the software version indicated on page 2 of the user manual matches the version installed in the luminaire. - Page 5 German Light Products® • If you have questions about the safe installation, operation or maintenance of the impression FR1 TM, please contact an authorized GLP distributor (see list of distributors at www.glp.de). • Use the luminaire only as directed in this user manual. Observe all markings in this user manual and on the luminaire.
- Page 6 Fire safety and protection from burns • Do not operate the luminaire if the ambient temperature (Ta) exceeds 45° C (115° F). • The surface of the luminaire’s casing can reach up to 55° C (131° F) during operation.
- Page 7 If no fixed structure is available, secure the luminaire using the safety cable and retaining collar supplied with the luminaire (or identical replacement items supplied by GLP) as directed in this manual. impression® FR1 TM User Manual...
- Page 8 • If the luminaire becomes damaged, stop using it immediately and remove it from the installation. Do not attempt to use a luminaire that is obviously damaged. • Do not modify the luminaire in any way not described in this user manual. • Install genuine GLP parts only. impression® FR1 TM User Manual...
-
Page 9: Avoiding Damage
German Light Products® Avoiding damage Do not point the front of the luminaire towards the sun or other strong light sources. The front lens focuses and concentrates light just like a magnifying glass. Strong light can cause internal damage to the luminaire, melting components or starting an internal fire within seconds. -
Page 10: Product Overview
Product overview Figure 2: Product overview A – Front lens assembly F – Cooling vent B – Control panel with backlit LCD display G – Wireless control linking button C – Wireless control antenna H – Mechanical fastener lever locking screw D –... -
Page 11: Product Features
German Light Products® Product features The impression® FR1 TM from GLP® is a high-quality moving head lighting luminaire with a 60 watt RGBW LED and advanced optics that give a powerful, homogenous and sharply defined beam throughout the luminaire’s 10:1 zoom range. Advanced... - Page 12 If you use the color presets channel, we recommend that you set RGBW levels to 100% as a starting point before selecting a color preset. After you have selected a color on the color preset channel you can then fine-tune it using the RGBW channels.
- Page 13 German Light Products® Fan modes The four different cooling fan modes give you a range of options to choose from depending on how much you want to give priority to high-intensity light output or to low fan noise: • Regulated gives priority to light output. If the luminaire is blacked out, fans run at minimum speed.
- Page 14 No-DMX (behavior when the luminaire is not receiving a DMX signal) You can set the luminaire to respond in four different ways if no DMX signal is present (if the luminaire is being controlled by DMX but the DMX signal stops, or if you apply power to the luminaire when no DMX signal is present): •...
-
Page 15: Preparing For Use
German Light Products® Preparing for use Warning! Read ‘Safety’ starting on page 4 for important safety information that you must understand before you install or operate the luminaire. Included Items See Figure 4. The impression FR1 TM is supplied with the following items: •... - Page 16 See Figure 5. At the end of the track adapter next to the wireless linking button, use the lever (arrowed) to close the main mechanical fastener. This will fix one side of the luminaire into the track and make the connection to the Neutral line inside the track.
- Page 17 German Light Products® Safety cable option 1: Anchoring to a building or rigging structure Provide a secure anchoring point such as a building member, eyebolt screwed into a secure surface or rigging structure. Obtain a safety cable that is approved by TÜV, UL or a similar organization as a safety attachment for the weight of the luminaire.
- Page 18 See Figure 9. Attach the free end of the safety cable to the safety cable anchoring point in the luminaire’s baseplate using the lockable carabiner clip (arrowed in Figure 9) on the end of the safety cable. Fasten the lock on the carabiner clip so that the safety cable cannot become unfastened from the luminaire.
- Page 19 German Light Products® Setting up for DMX control To configure the luminaire for control via DMX, open the menus in the fixture’s control panel and set the fixture’s DMX Address. Note the following: • The FR1 TRM uses 16 DMX channels. If individual control of luminaires is required, each luminaire must have its own 16 channels in the 512 channels that are available in one DMX universe.
- Page 20 Advice and assistance If you would like advice with planning or implementing a DMX control system over LumenRadio CRMX, your GLP supplier will be happy to help. impression® FR1 TM User Manual...
-
Page 21: Control Menus And Lcd Display
German Light Products® Control menus and LCD display Warning! DMX control is disabled when the control menus are active. Be prepared for the head to move as soon as you exit the control menus. The control panel and LCD display provide access to user settings, readouts, and utilities. -
Page 22: Control Menu Layout
Control menu layout DMX Start 1 - 512 DMX start address Address Setup DMX Mode NORM Invert Pan ON / OFF Invert pan left/right Invert Tilt ON / OFF Invert tilt up/down Swap ON / OFF Swap Pan/Tilt channels... - Page 23 German Light Products® Luminaire blacks out if Blackout DMX signal is lost Last DMX values are held Hold if signal is lost Luminaire goes to stored DMX Hold Stand-Alone stand-alone scene if DMX signal is lost Take snapshot of current DMX Shot scene and save it as stand-alone scene...
- Page 24 -128 - 127 Current °C/°F Maximum -128 - 127 Main head Main resettable °C/°F temperature Temperature sensor readouts Maximum -128 - 127 non- °C/°F resettable Temperatures -128 - 127 Current °C/°F Maximum -128 - 127 resettable °C/°F temperature Temperature...
- Page 25 German Light Products® Full System Confirm (Yes/No) Reset luminaire Reset Pan/Tilt Reset pan and tilt Reset Confirm (Yes/No) Reset only LED Driver Confirm (Yes/No) Reset LED driver only Reset 0 - 255 Zoom 0 - 255 Pan rotation 0 - 255 Manually apply Special 0 - 255...
- Page 26 ON / OFF Test Colour ON / OFF Run test sequence ON / OFF Enter code (contact GLP if you would like the code) to access Service Menu (resets Enter Code 0 - 255 automatically after luminaire restart or after 10 min. with no...
-
Page 27: Dmx Channel Layout
German Light Products® DMX channel layout Normal mode (16 DMX channels) Default Channel Function Description % Range* Fade range Pan coarse -314.5° to +314.5° (16 bit) 0 – 65535 32768 0 – 100% Fade Pan fine Tilt coarse -105° to +105° (16 bit) 0 –... - Page 28 Control/Settings Idle 0 – 11 0 – 4.3% Snap (see notes at No function 12 – 26 4.7 – 10.2% end of this Performance = Fast* 27 – 29 10.6 – 11.4% table) Performance = Normal* 30 – 32 11.8 –...
- Page 29 German Light Products® 607 Hz** 68.6% 608 Hz** 69.0% continued 609 Hz** 69.4% 610 Hz** 69.8% 611 Hz** 70.2% 612 Hz** 70.6% 613 Hz** 71.0% 614 Hz** 71.4% 615 Hz** 71.8% 616 Hz** 72.2% 617 Hz** 72.5% 618 Hz** 72.9% No function 187 –...
-
Page 30: Service And Maintenance
Lubrication The only parts that may require occasional lubrication are the focus/zoom rails. Contact GLP Service and Support for advice. Removing and reinstalling the micro-Fresnel lens If you would like to obtain a sharper-edged beam, you can remove the micro-Fresnel lens that is installed in the front of the head (bear in mind that this will result in a slight loss of evenness in the beam projection). - Page 31 German Light Products® To remove the micro-Fresnel lens: Shut down power to the luminaire and allow it to cool. Figure 12. Removing a micro-Fresnel lens See Figure 12. Remove the three Phillips #1 screws (arrowed) from the lens in the front of the head.
- Page 32 Figure 14. Location of main fuse GLP Service and Support Contact information for the nearest GLP Service and Support is available online at www.glp.de/en/service, by request via email at info@glp.de, or by telephone at the following numbers: •...
-
Page 33: Technical Specifications
German Light Products® Technical specifications Light source LED type: Osram Ostar RGBW LED lifetime: 50.000 hours Number of LEDs: 1 CRI (Ra): 80 TLCI: 80 TM30-15 77/106 Optics Min. zoom angle: 3.7° Max. zoom angle: 35° Zoom range: 10:1 Effects Color mixing: RGBW continuous Color presets: 12 + 3 whites, adjustable via RGBW Color temperature correction: 2500 K –... - Page 34 Electrical AC power: 100-240 V, 50/60 Hz Maximum power consumption @230 V: 80 W Power consumption at idle: 14 W Primary fuse: 20 mm T 2A EEC (Energy Efficiency Class): E EEI (Energy Efficiency Index): 1.193 Energy consumption (kWh/1 000 h): 68...
-
Page 35: Dimensions
German Light Products® Dimensions Dimensions given in millimeters impression® FR1 TM User Manual...