Advertisement
Available languages
Available languages
•
Do not exceed the maximum filling volume as indicated on the appliances.
•
Do not use this appliance to stir paint. Danger, could result in an explosion.
•
Do not let the power cord come into contact with hot surfaces or hang over the edge of a table or counter.
•
Never use accessories or parts made by other manufacturers not recommended or sold by Electrolux
as it may cause a risk of injury to persons.
•
This appliance is for indoor use only.
•
This appliance is intended for domestic use only. Electrolux will not accept any liability for possible
damage caused by improper or incorrect use.
GETTING STARTED
1. Before using the blender for the first time, make sure all the packaging has been removed before
operating the appliance. Wash all parts except for the motor base (G).
1a. For glass jug model: Ensure that the rubber seal (E) is properly placed on the blade assembly (F). Invert
the jug (D) to have its base facing upward. Turn the blade assembly over and insert it into the jug base by
aligning its slots with the catches on the jug base. Turn the blade assembly anti-clockwise to lock it securely.
1b. For plastic jug model: Attach the blade assembly (M) to the bottom of the jug (D). Fix it firmly by
turning it anti-clockwise.
Caution! The blades are very sharp!
2. Place the motor housing on a flat surface. Ensure the speed selector (H) is set to "OFF" before placing
the jug (D) on the motor base (G). Place the jug on the motor base. There are 2 possible positions,
handle on the right or on the left. Rotate clockwise until it locks. The blender is designed with a safety
locking system. When the arrow on the jug (
jug is locked in position. The blender will operate only if the jug or the grinder is locked correctly. Put the
ingredients in the jug. (Do not exceed the maximum capacity indicated on the jug.)
Processing hot liquids: allow hot liquids to cool down until lukewarm before filling the jug. Fill the jug
only half full and start processing on low speed.
For Glass Jug: For best result when processing diluted liquids, the maximum processing volume shall be 1.25L.
3. Close the lid and insert the measuring cup (A) in the filler hole and lock into position. Do not operate
the blender if the lid is not locked in.
4. Start the blender by turning the speed selector (H) clockwise. Start at low speed, then progress to a higher
speed if required. To use the PULSE function, turn the speed selector to PULSE position and release.
For heavy load, please remove half of the contents and process them in 2 batches.
5. Ice crushing: Turn the speed selector (H) to PULSE position and hold for 3-5 seconds several times until
you obtain a satisfactory result. You can add more ice through the filler hole while the blender is running.
The PULSE function allows greater control when blending, e.g. when chopping nuts or chocolates, or crushing ice.
6. To make juice: Insert the filter (K)* as illustrated. Make sure it fits correctly. Add fruits in the filter*, close
the lid (B) and process as usual. Caution! Always remove the seed from stone fruits such as plums,
peaches, apricots, avocados before processing them in the blender.
USING THE GRINDER*
The grinder* consists of a grinder bowl (L) and a blade assembly (M). It can be used to chop nuts, dried
fruit, bread crumbs, garlic, onions etc.
7. Make sure the unit is unplugged and the speed selector (H) is set to "OFF" before placing the grinder
on the motor base (G). Turn the grinder upside down and carefully remove the blade assembly (M) by
turning it anti-clockwise. Fill the grinder bowl with the desired ingredients. Do not fill more than half full.
8. Attached the blade assembly (M) to the grinder bowl (L) by turning the blade assembly clockwise.
NOTE: If it is not tightly attached together the blender will not work due to a safety mechanism.
9. Turn the grinder the right way up and lock into place on the motor base (G) by turning clockwise.
Plug in the appliance and select the desired speed setting. Caution! Do not operate the grinder
continuously for more than 30 seconds. For better results, use the PULSE setting.
* Specifications vary by model
www.electrolux.com
) is aligned with the arrow (
) on the motor base, the
EN
CNS
CNT
KR
ID
TH
VN
5
Advertisement
