Getting Started; Using The Grinder - Electrolux UltimateTaste 300 Instruction Book

• Be careful if hot liquid is poured into the food processor or blender as it can be ejected out of the
appliance due to a sudden steaming.
• Do not exceed the maximum filling volume as indicated on the appliances.
• Do not use this appliance to stir paint. Danger, could result in an explosion.
• Do not let the power cord come into contact with hot surfaces or hang over the edge of a table or counter.
• Never use accessories or parts made by other manufacturers not recommended or sold by Electrolux
as it may cause a risk of injury to persons.
• This appliance is for indoor use only.
• This appliance is intended for domestic use only. Electrolux will not accept any liability for possible
damage caused by improper or incorrect use.
• This appliance is suitable to operate on both 50 and 60Hz.
• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device, such as a timer, or connected
to a circuit that is regularly switched on and off by the utility.

GETTING STARTED

1. Before using the blender for the first time, make sure all the packaging has been removed before
operating the appliance. Wash all parts except for the motor base.
Caution! The blades are very sharp!
2. Place the motor housing on a flat surface. Ensure the speed selector is set to "0" before placing the jug on
the motor base. Place the jug on the motor base, with handle on the right. Rotate clockwise until it locks.
The blender is designed with a safety locking system. The blender will operate only if the jug or the grinder is
locked correctly. Put the ingredients in the jug. (Do not exceed the maximum capacity indicated on the jug.)
Processing hot liquids: Do not process hot liquid. Allow hot liquids to cool down until lukewarm
(around 40oC) before filling the jug. Fill the jug only half full and start processing on low speed.
3. Close the lid and insert the measuring cup in the filler hole and lock into position. Do not operate the
blender if the lid is not locked in.
4. Start the blender by turning the speed selector clockwise. Start at low speed, then progress to a higher
speed if required. To use the PULSE function, turn the speed selector to PULSE position and release.
For heavy load, please remove half of the contents and process them in 2 batches.
5. Ice crushing: Turn the speed selector to PULSE position and hold for 3-5 seconds several times until you
obtain a satisfactory result. You can add more ice through the filler hole while the blender is running.
The PULSE function allows greater control when blending, e.g. when chopping nuts or chocolates, or crushing ice.

USING THE GRINDER*

The grinder* consists of a grinder bowl and a blade assembly. It can be used to chop nuts, dried fruit,
bread crumbs, garlic, onions etc.
6. Make sure the unit is unplugged and the speed selector is set to "0" before placing the grinder on the
motor base. Turn the grinder upside down and carefully remove the blade assembly by turning it anti-
clockwise. Fill the grinder bowl with the desired ingredients. Do not fill more than half full.
7. Attached the blade assembly to the grinder bowl by turning the blade assembly clockwise. NOTE: If it
is not tightly attached together the blender will not work due to a safety mechanism.
8. Turn the grinder the right way up and lock into place on the motor base by turning clockwise. The
triangle mark on the grinder should align with the lock mark on the grinder blade assembly. Plug in the
appliance and select the desired speed setting. Caution! Do not operate the grinder continuously for
more than 30 seconds. For better results, use the PULSE setting.
9. When the ingredients have been ground/chopped to the desired consistency, unplug the appliance,
and remove the grinder from the appliance. NOTE: Do not remove the grinder bowl directly from the
motor base as this will cause the ingredients to spill out and expose the blade assembly.
* Specifications vary by model
www.electrolux.com
EN EN
CNS
CNT
KR
ID
TH
VN
AR
5