Advertisement
Quick Links
Dahlia Bedside Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
A
B
dowel
screw
x12
x8
G
H
slide
slide
rail x2
rail x2
WARNING:
Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that different wall materials may require different fixing
devices from those supplied.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558
C
D
E
locking
small
bolt
nut x20
x20
screw x20
I
J
K
slide
wedge
plastic
rail x2
x4
glide x4
Hardware Supplied
Phillips & Flathead screwdrivers
and hammer required
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
V
F
safety
slide
strap x1
rail x2
L
screw
x4
W
X
Y
screw
wall
wall
washer
x1
anchor
screw
x1
x1
Wall Strap
Z
x2
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Mocka Dahlia Bedside Table
Summary of Contents for Mocka Dahlia Bedside Table
- Page 1 Phillips & Flathead screwdrivers and hammer required For quicker assembly, we recommend the use of a power drill on a low-speed setting. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 2 Attach 2x slide rails (G) to panel [3] and secure with 6x small screws (E). Tighten with a screwdriver. Insert 4x bolts (C) into panel [2]. Tighten with Insert 4x bolts (C) into panel [3]. Tighten with a screwdriver. a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 3 4x locking nuts (D). Tighten with a screwdriver. secure with 4x locking nuts (D). Tighten with a screwdriver. Attach 4x plastic glides (K) to the panels [2] and [3] using a hammer as shown. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 4 Insert 4x bolts (C) to panel [1]. Tighten with a screwdriver. Slide panel [7] down along the grooves between the panels [2] and [3] to form the back of the unit as shown. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 5 Insert 4x bolts (C) into panel [8]. Tighten with a screwdriver. Attach panel [1] to the unit with 4x dowels (A) and secure with 4x locking nuts (D). Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 6 Slide panel [9] along the grooves between the panels [11] and [12] . Attach panels [11] and [12] to panel [8] secure with 4x locking nuts (D). Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 7 Attach slide rail (I) and slide rail (H) to the underside of the side panels Tighten with a screwdriver. as shown. Secure with 4x small screws (E) and tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 8 4x screws (L). Tighten with a screwdriver. Attach 1x safety straps (V) to the top of the back side of the unit as shown using 1x washers (Z) and 1x screws (W). Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
- Page 9 (V). Fasten to the wall using 1x washer (Z) , 1x wall anchor (X) and 1x wall screw (Y). Ensure unit is balanced and steady before use. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Need help?
Do you have a question about the Dahlia Bedside Table and is the answer not in the manual?
Questions and answers