Advertisement
PV OFFSET: Adjust input compensation of PV
PV GAIN: Adjust input gain of PV
SV SLOPE: Set up rising slope (when CRTS = SLOP)
ANALOG OUT1 MAX.: Adjust upper limit compensation for analog Output 1
(1scale = 1μA; 1scale = 1mV)
ANALOG OUT1 MIN.: Adjust lower limit compensation for analog Output 1
(1 scale = 1μA; 1scale = 1mV)
ANALOG OUT2 MAX.: Adjust upper limit compensation for analog Output 2
(1scale = 1μA; 1scale = 1mV)
ANALOG OUT2 MIN.: Adjust lower limit compensation for analog Output 2
(1scale = 1μA; 1scale = 1mV)
RETRANSMISSION MAX.: Adjust upper limit compensation for Retransmission
(1scale = 1μA) (display when a Retransmission Card is connected to CND3)
RETRANSMISSION MIN.: Adjust lower limit compensation for Retransmission
(1scale = 1μA) (display when a Retransmission Card is connected to CND3)
REMOTE GAIN: Adjust Remote gain (When CRTS = REMO)
REMOTE GAIN: Adjust Remote compensation (When CRTS = REMO)
REMOTE LOW: Remote lower limit (When CRTS=REMO)
REMOTE HIGH: Remote higher limit (When CRTS=REMO)
EVENT1: Set up EVENT1 function (display when a Event Card is connected to EVENT1)
EVENT2: Set up EVENT2 function (display when a Event Card is connected to EVENT2)
EVENT3: Set up EVENT3 function (display when a Event Card is connected to EVENT3)
PID mode: Any of the 6 PID groups can be selected. When set to AUTO mode, the program will automatically select the PID group that is
the closest to the target temperature.
Select 0~5 group of PID and execute AT function, the system will automatically load P; I; D and IOF parameters into the selected PID
group.
th
Select the n
PID (n = 0 ~ 5)
th
Set up the 0
PID temperature value
th
Set up the 0
proportional band value
th
Set up the 0
Ti value
th
Set up the 0
Td value
th
Set up the 0
PID integral deviation
Press
Programmable Editing: set
Select desired editing pattern number 0~F
Edit the temperature of step No.0 of pattern No. 0
Edit the time of step No.0 of pattern No. 0 (time unit:
hh, mm)
~
Set up step 0~15 in order
Edit the temperature of step No.15 of pattern No.0
Edit the time of step No.15 of pattern No.0
Seelect the actual required steps for executing
pattern No.0
Set up the additional cycle (0~199) for pattern No.
0 execution
Set up the link pattern of pattern No.0 (0~F;
END; STOP)
selection of desire editing pattern and number.
press
to set the parameters in
"Regulation Mode"
to
or
If the setting is OFF, leave the editing pattern page and go to
press
Press
to return to the
press
~
~
~
~
~
and set
to
.
press
~
Edit the temperature of step No.0 of pattern No. 15
~
Edit the time of step No.0 of pattern No.15 (time unit:
hh, mm)
~
~
Edit the temperature of step No.15 of pattern No.15
~
Edit the time of step No.15 of pattern No.15
~
Seelect the actual required steps for executing
pattern No.15
~
Set up the additional cycle (0~199) for pattern No.
15 execution
~
Set up the link pattern of pattern No.15 (0~F;
END; STOP)
th
to set 0 ~ 5
PID parameters
th
Set up the 5
PID temperature value
th
Set up the 5
proportional band value
th
Set up the 5
Ti value
th
Set up the 5
Td value
th
Set up the 5
PID integral deviation
Press
to set the parameters in
"Regulation Mode"
to set the desired editing pattern number 0~F
to continue with the setting.
Press
selection of desire editing pattern and number
0.0
0.000
0
0
0
0
0
0
0
0
0
100
OFF
OFF
OFF
press
to return to the
6
Advertisement
