Advertisement
ALARM3 DELAY: Set up Alarm 3 delay (refer to "Alarm Outputs" ) (display when OUT2 is set to
ALARM mode)
PV Color Change Function: Select the alarm to change PV display color. (refer to "Alarm Outputs")
2PID change temperature (display on 2PID control mode)
2PID reset temperature (display on 2PID control mode)
REMOTE TYPE: Set up Remote type (display when
(V0:0~5V; V1:1~5V; V10:0~10V; MA0:0~20mA; MA4:4~20mA)
Select auxiliary function 1
Select auxiliary function 2
COMMUNICATION WRITE: Enable/disable communication write-in
COMMUNICATION SELECT: Select ASCII or RTU format
COMMUNICATION NO.: Set up communication address
BPS: Set up baudrate
LENGTH: Set up data length
STOP: Set up stop bit
PARITY: Set up parity bit
【Regulation Mode】Parameter Settings:
Display
AT: Auto-tuning Switch（display when setting Ctrl = PID/FUZZY/2PID, TUNE = AT, R-S=RUN）
ST: SELF-TUNING Switch (display when setting Ctrl = PID, TUNE = ST)
PID NO.: Select the n
setting Ctrl=PID)
PID SV NO.: Accordinig to the selection of PID No. (n=0~5), set SV value accordingly. It will allow
~
the system perform auto selection when it's set to AUTO mode. (Display when Ctrl =
PID/FUZZY/2PID).
P : Proportional Setting (display when setting Ctrl = PID/FUZZY/2PID and TUNE = AT)
~
Set P value according to the selection of PID No. (n=0~5). When P is set to AUTO, the system will
select P value accordingly.
I: Integral Time Setting (display when Crtl=PID/FUZZY/2PID; this parameter is set automatically
~
when TUNE=AT.)
Set I value according to the selection of PID No. (n=0~5). When I is set to AUTO, the system will
select I value accordingly.
D: Deviation Time SEtting: (display when Crtl=PID/FUZZY/2PID; this parameter is set
automatically when TUNE=AT.)
~
Set D value according to the selection of PID No. (n=0~5). When D is set to AUTO, the system will
select D value accordingly.
I OFFSET: Integral deviation setting, when Integral is not 0. (display when Crtl=PID/FUZZY/2PID;
this parameter is set automatically when TUNE=AT.)
~
Set IOF value according to the selection of PID No. (n=0~5). When IOF is set to AUTO, the
system will select IOF value accordingly.
PD OFFSET: PD offset when Integral=0 to eliminate a consistent deviation.
Set up Fuzzy gain value (when Ctrl=FUZZY)
Set up Fuzzy Deadband (when Ctrl=FUZZY)
OUT1 HYSTERESIS: Adjust Output 1 hysteresis (when in ON/OFF control)
OUT2 HYSTERESIS: Adjust Output 2 hysteresis (when in ON/OFF control)
OUT1 HEAT: Heating control cycle for Output 1 ( when Ctrl= PID/FUZZY/MANUAL/2PID)
OUT1 COOL: Cooling control cycle for Output 1 (when Ctrl= PID/FUZZY/MANUAL/2PID)
OUT2 HEAT: Heating control cycle for Output 2 ( when Ctrl= PID/FUZZY/MANUAL/2PID)
OUT2 COOL: Cooling control cycle for Output 2 (when Ctrl= PID/FUZZY/MANUAL/2PID)
COEF: Ratio of Output 1 against Output 2 (when Ctrl= PID/FUZZY/2PID and when in dual output
control)
DEAD: Set up deadband (when Ctrl is not set to MANUAL and when in dual output)
PV FILTER: Set up input filter factor of PV
PV RANGE: Set up input filter range of PV
Description
th
(n=0~5) PID. When set in AUTO, PID is auto-selected. (display when
is set to REMO mode)
Press
to return to input type setting
Press
0
OFF
1.0
0.5
MA4
0
0
OFF
ASCII
1
9600
7
1
E
Factory Setting
OFF
OFF
0
100
47.6
260
41
0
0
4
0
0
0
Output
selection:
C; V; S: 5sec.
R: 20sec.
1.00
0
1
1.00
5
Advertisement
