Wired Zone Expansion (4219, 4229); Installing Zone Expansion Units; Connections And Set-Up; Figure 11.Êêwiring Connection, 4219 & 4229 (4229 Shown) - First Alert FA162C Installation Instructions Manual

Section 5. WIRED ZONE EXPANSION
This section provides information regarding the use of expansion modules for expanding the
number of wired zones in the system, the modules that can be used and their wiring
connections.

Installing Zone Expansion Units

Connections and Set-Up

=
OFF ON
@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @
@ @ h ? @ @ h ? @ @ @ @
@ @ h ? @ @ @ @
@ @ h ? @ @ h ? @ @
@ @ h ? @ @
@ @ @ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @
@ @ @ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @
@ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ g ? @ @
@ @ g @ @ g ? @ @ ? @ @
@ @ @ @ @ @ @ @ @ @ g ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? @ @
@ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @
RELAY
CONNECTOR
RLY
2
RELAYS
"OFF"
You can add an additional 8 wired EOLR zones to the basic control's 8 zones,
for a total of 16 wired zones, by using a No. 4219 Wired Expansion Unit, or
4229 Wired Expansion/Relay Unit.
Location
Supervision
Zone Information ¥ Assign zone numbers 10Ð17 for the eight wired
1. Connect the 4219 or 4229 module to the control's keypad terminals (see
diagram below).
2. Set the 4219 or 4229's DIP switch for device address "1" (switch 2 "OFF"
and switches 3, 4, 5 "ON"). Switch 1 determines expansion zone A's
response time ("ON" = normal response, "OFF" = fast response). For
location of the DIP switch in the unit, see the diagram below (location of
DIP switch for both units is in the same location).
For additional information, see instructions supplied with the 4219 and
4229.
RELAY
DIP SWITCH
2
FOR SETTING ADDRESS
AND ZONE "A" RESPONSE
}
RELAY
1
NO C NC
}
TAMPER JUMPER POSITION
4229 IN CABINET
(NOT TAMPERED)
4229 REMOTE
(TAMPER PROTECTED)
1 2 3
RLY
REED
1
(TAMPER)
SWITCH
1K
A B
ZONES:
Figure 11. Wiring Connections, 4219 & 4229 (4229 shown)
¥ You can mount an expansion unit within the control
cabinet if space permits. Otherwise, mount the unit
outside the cabinet.
¥ Units are supervised against removal. Keypads will
display CHECK and zone 09 if a zone expander is
disconnected.
¥ Units have tamper protection for security when
mounted outside of the cabinet.
expansion loops (designated A to H).
program these zones individually (in 56 interactive
mode) for Partition 1 or 2. Expansion zones must
also be programmed as input type 2 (AW) when
prompted.
4229
EITHER OR BOTH CAN BE USED
4-PIN CONSOLE PLUG
TB1
4 5 6 7 8 9 10 11 12
C D E F G H
–21–
TERMINALS ON
CONTROL PANEL
TB2
GRN DATA OUT
4
TO CONTROL
BLK
(–) GROUND
4 3
3
RED
(+) 12V
2
2
YEL DATA IN
1
1
FROM
CONTROL
TERMINATE EACH
PROGRAMMED ZONE
WITH 1000 OHM (1K)
END-OF-LINE RESISTOR
(EACH ZONE'S MAX.
LOOP RESISTANCE:
300 OHMS + E.O.L.)
You can
(TERM 6)
(TERM 4)
(TERM 5)
(TERM 7)