Table of Contents + Safety TABLE oF ConTEnTS SAFETY LABELS Safety ..... . 2-3 understanding the Machine safety labels: Parts ..... 4-6 The machine safety labels shown in this section are placed in important areas on your machine to draw attention to Assembly .
Safety opErATing SAFELY rECommEndEd VEhiCLES and Attachment Method General: If you have purchased an optional mount kit, follow mount • Read this manual and the manual of the vehicle kit instructions for proper assembly of spreader to vehicle. you are attaching the spreader onto. Be thoroughly familiar with the controls and the proper use of the If a mount kit is not available for your vehicle, and you are equipment.
Hopper Bottom Bearing 1008785 Caution Label 1000211 Dial Mount 1008757 Frame with Label 1000215 Pine Tree Clip L-1744-6 Spyker Serial # Label 1000725-01 Rate Gate Link 1008770 Bumper Bar 1000733 Dial 2M0828SS Bolt; SS, 1/4" x 1-3/4" 1008711 Gate Actuator Bracket...
Page 5
Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. pLEASE CALL: 1 ( 800 ) 972 - 6130 hopper Explosion rate gate Explosion English Manual 1008754-B...
Page 6
Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. pLEASE CALL: 1 ( 800 ) 972 - 6130 Gate Actuator and Extension Explosion Speed Control Explosion Frame/Spinner Explosion Deflector Explosion English Manual 1008754-B...
If spreader will be mounted onto a ZTR and the Gate Actuator Bracket (43) will be difficult to reach with foot (See Turn Spyker Dial (8) to setting 9.9. Cut the cable tie that is Figure 1), then the Gate Actuator Extension (44) may be holding the Gate Actuator Rod (21) in place. Slide the Gate required.
Page 8
Assembly Attach Plastic Spacer (52) to Gate Actuator Bracket (43) Pivot the Gate Actuator Bracket (43) in the direction shown using one #10-24 x 2-1/4" Bolt (51), two 1/4" Washers (27), until the Rate Gate (18; See Figure 5) has just closed but and a #10-24 Nylon Lock Nut (48) as shown in Figure 4.
Page 9
Assembly Adjust the position of the Plastic Spacer (52; See Figure 6) 10. Attach Grip (53) to Gate Actuator that was assembled in Step 7 so that it is resting against the Extension (44, if applicable) as shown in Figure 7. Frame (39) and tighten the fasteners that hold it in place.
Page 10
Assembly (Electrical Instructions) If you have purchased an optional mount kit, and if those Plug in Motor Harness to Motor (34). The Motor instructions explain how to connect and route an electrical connector and Motor Harness connector can only be harness, please refer to those instructions. If no instructions attached in one way.
Page 11
Mount Variable Speed Assembly Control Here (Electrical Instructions) SUGGESTION Fasten with Cable Ties Plug in Battery Harness connector to the Variable Continued... Speed Control (3). Mount SUGGESTION Variable Speed Control Here Black Black Black Route Around Route Beneath Seat Variable Speed Control Route Battery Harness to battery, and use Cable Ties (17) to properly secure to vehicle.
UTV - Utility Terrain Vehicle rECommEndEd UTV SpECiFiCATionS How to Attach to uTV's Review your Vehicle Operators Manual If you are developing your own mount, for your vehicle specifications. follow these guidelines: • Spreader should be mounted to rear of vehicle, • Minimum vehicle dry weight: 1,050 lb using UTV receiver hitch as the main support. • Minimum wheelbase: 70.9"...
Page 13
1-3/4 No front mount Optional side Deflector (Spyker Part #: KSP13-SD3) is a great addition for this spreader. Optional Cable Kit (Spyker Part #: KSP14-CAB1) is recommended to control rate gate from UTV driver seat. English Manual 1008754-B...
ATV - All Terrain Vehicle rECommEndEd ATV SpECiFiCATionS How to Attach to ATV's Review your Vehicle Operators Manual If you are developing your own mount, for your vehicle specifications. follow these guidelines: • Spreader should be mounted to rear of vehicle, • Minimum vehicle dry weight: 615 lb using ATV receiver hitch as main mount support. • Minimum wheelbase: 48.4"...
Page 15
22” Mount as close to ATV as possible Mount to ATV while allowing linkages to work. receiver hitch. 22” 5-1/8 1-3/4 6-3/4 1-3/4 Optional side Deflector (Spyker Part #: KSP13-SD3) is a great addition for this spreader. English Manual 1008754-B...
ZTR - Zero Turn Radius rECommEndEd ZTr SpECiFiCATionS How to Attach to ZTR's Review your Vehicle Operators Manual If you are developing your own mount, for your vehicle specifications. follow these guidelines: • Spreader can be mounted to front of vehicle • Minimum vehicle dry weight: 863 lbs • Fabricate a mount bracket using a minimum of 2" x • Minimum mower deck: 48"...
Page 17
Center Spreader on ZTR Mount spreader over ROPS Mount Spreader over ROPS caster wheels Caster Wheels 22” 22” 5-1/8 Do not 1-3/4 mount high 6-3/4 1-3/4 Optional side Deflector (Spyker Part #: KSP13-SD3) is a great addition for this spreader. English Manual 1008754-B...
The dial is marked from 0 to 9.9. The rate gate linkage position determines the amount of material to be broadcast. Set dial to correct position. If a Spyker dial setting is not The higher the number, the heavier the application of...
Page 19
Read Before Using BECOME FAMIlIAR WITh ThE OPERATION OF ThE SPREADER BEFORE YOU PUT MATERIAl IN ThE hOPPER ACCUwAY SprEAd pATTErn AdjUSTmEnT Caution! To avoid injury to hand, ensure motor controller is switched OFF before adjusting Accuway. ↑ As you spread, if the spread pattern is skewing or flowing heavy to one side, simply loosen the T-knob (15) on the Accuway plate (20) and slide the T-knob forwards or backwards.
Read Before Using BECOME FAMIlIAR WITh ThE OPERATION OF ThE SPREADER BEFORE YOU PUT MATERIAl IN ThE hOPPER SprEAding ChArT This unit is designed to handle dry, clean, free-flowing material only such as bagged rock salt, ice melt, fertilizer, and grass seed. Do not use bulk rock salt or water softener salt. It may be necessary to remove agitator for some materials, such as bagged rock salt.
Page 21
NOTE: Dial Settings Are Approximate Only ! Dial Settings Dial Settings Full Rate Half Rate Lbs. per Once Over Twice Over Product Particle Size 1000 sq. ft. Fine Pellets Mixed Fine Pellets Small Pellets Nitrogen Pellets Medium Size Medium Pellets And Granuals Large Heavy Pellets...
• Open and close gate as you rinse to avoid build up damaged parts (including safety decals). of material. • If agitator is worn, replace with Spyker part #1008241. • Quickly towel dry spreader. Do not use any other agitator.
Read Before Using BECOME FAMIlIAR WITh ThE OPERATION OF ThE SPREADER BEFORE YOU PUT MATERIAl IN ThE hOPPER TroUBLEShooTing PROBleM CAuse / CONDITION ReMeDY Too much/not enough Rate gate not opened to correct position Check dial settings and rate gate linkage material dispensed position Rate gate linkage...
1 YeAR lIMITeD WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems,...
Need help?
Do you have a question about the S80-12010 and is the answer not in the manual?
Questions and answers