Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SPYKER BCS25
Summary of Contents for SPYKER BCS25
- Page 1 OPeRATOR'S MANuAl BCS25 - 25lb Bag Spreader Spyker Spreaders Contact us at 800.972.6130 www.spyker.com IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! English Manual Page 1...
-
Page 2: Table Of Contents
Table of Contents + Safety Table of ConTenTs operaTing safely General Safety ..... 2 Parts ......• Projected particles can cause eye damage. Do not operate spreader near bystanders or animals. -
Page 3: Parts
Part List DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. Please Call: 1 (800) 972-6130 Part # Description Parts within assembled spreader body: 1019473 Bag Assembly Retainer Ring with 1020075 Gasket 1020074 Base with Labels 1019492 Torsion Spring 1019490 Gate Lever Washer; 1019491 Oversized M4 Screw; Thread 1019496 Forming, M4 x 16 1019489 Gate 1019485 Coupling, M8 x 1.25... -
Page 4: Assembly
Assembly 1. Adding Support Rod NOTE: Flip the spreader upside down for this step. Inside the bag (not illustrated) find the rim of the 3. Two small openings can be found along the shorter bag retainer (2). On the opposite side of the handle, flat edge of the spreader base (3). Using these you will find a slightly extended opening. openings, slide the Broadcast Shield (17) into place as illustrated below. Slide the bag support rod (19) in place here, as illustrated below. This shield will securely snap into place. Fig. 1 Fig. 3 NOTE: Tilt spreader base slightly back and look underneath the fan for this step. -
Page 5: Use And Care
Use and Care MainTenanCe appliCaTion guiDe • Use only a dry lubricant, such as 1. Set the calibration knob (10) to the desired setting silicone or graphite on all moving parts. (Reference the Settings chart on page 7). • Do not use oil or grease. a. If there is not a calibration setting for the material you’re • Keep unit clean and dry. spreading, follow the steps to calibrate for this material on page 6. 2. Before filling the bag, adjust the shoulder strap such that the sTorage spreader sits on your left hip when hung from your left shoulder. 3. Ensure that the gate is closed, place the spreader on the • Store indoors in a dry place. ground or other flat surface, then fill the bag. • Do not store with seed or other 4. Start walking and begin to turn the crank handle clockwise materials in the bag. -
Page 6: Calibrating Guide
Use and Care The goal is to determine which setting on the calibration knob will correspond to the recommended application rate for the material being spread. The application rate will be printed on the bag or container that the material was supplied in. Locate the application rate before proceeding with the calibration trial. CalibraTion 1. Measure a distance of 25 feet on grass or another 7. Calculate the actual application rate surface that will prevent the spread particles from using the following formulas: bouncing (such as a large blanket or loose dirt) and mark 8. Determine the weight of the material spread in pounds: a start and finish line. Initial Weight ______ lbs HOW TO CAlCulATe - Final Weight ______ lbs MATeRIAl SPReAD = Material Spread ______ lbs 25 ft 9. Next, find the area covered in square feet: Spread Width ______ ft HOW TO 2. Fill the bag approximately 3/4 full & weigh the spreader. CAlCulATe Record this weight in pounds as Initial Weight. -
Page 7: Settings
Factors such as variation in material density, moisture in the material, walking speed, cranking speed, and ground conditions will affect the application rate of the spreader. Because of this variation, Spyker makes no warranty as to the uniformity of coverage actually obtained from the settings listed or determined using the calibration trial. -
Page 8: Warranty
1 yeAR lIMITeD WARRANTy This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. Spyker Spreaders will not be liable for any loss, damage or expense including, but not limited to, consequential or incidental damages, arising from the operation, condition or use of the item. The sole and exclusive remedy against Spyker Spreaders being the replacement of the defective parts. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This express warranty, which is applicable only to the original purchase, is in lieu...
Need help?
Do you have a question about the BCS25 and is the answer not in the manual?
Questions and answers