Advertisement
Quick Links
Advertisement
Related Manuals for SPYKER S40 Series
Summary of Contents for SPYKER S40 Series
- Page 1 Operator's Manual Model P40/S40 Series This manual contains information for the safety IMPORTANT of persons and property. Read it carefully before assembly and operation of the equipment! Spyker Spreaders Contact Us at 800.972.6130 ©2011 Brinly-Hardy Co. 1007895 Rev. D...
- Page 2 Hopper Explosion Rate Gate and Defl ector Explosion Handle Explosion 1007895 Rev. D...
- Page 3 Spinner/Axle Explosion Frame Explosion *As needed for shimming 1007895 Rev. D...
- Page 4 Item Part Number Qty Description Item Part Number Qty Description 1007770-01 Handle Stainless Number Not Used 1008052-10 Handle Painted Number Not Used 1007773 Control Lever Number Not Used 05-90-0054 1/4" x 1-1/2" Bolt, SS Number Not Used 05-92-0008 1/4" Washer, SS Number Not Used 05-94-0051 Nylon Flange Bushing...
- Page 5 Figure 3 Align the Cross Braces to the Hopper and Axle Supports as shown in Figure 3. Using (4) Figure 1 1-1/2" Bolts and Nylon Locknuts, assemble both Cross Braces. Tighten Cross Brace Bolts securely. Push Spreading Spinner onto Spinner Shaft as shown in Figure 1.
- Page 6 Figure 6 Figure 8 Install Linkage to Lever as shown in Figure 8. Install Wheel on the opposite side of the Axle (valve stem out) until it touches Axle Bearing and Washer. Install Washer onto Axle. Push Rue Ring Locking Pin through Axle hole. NOTE: Rue Ring Locking Pin will snap into position as shown in Figure 6.
-
Page 7: Operate Safely
Figure 11 Figure 10 10. Attach Handle Assembly to Frame using (4) 11. Install Handle Grips on Handle of Spreader as 1/4 x 1-1/2" Bolts and 1/4" Nylon Locknuts shown in Figure 11. as shown in Figure 10. READ BEFORE USING OPERATE SAFELY Keep bystanders away when you operate this machine. -
Page 8: Read Before Using
READ BEFORE USING Become Familiar With The Operation Of The Spreader Before You Put Material In The Hopper • Practice walking with the spreader, opening and dial setting on the low side. If the setting proves to closing the rate gate at the appropriate times. be too low, cover the area more than one time. - Page 9 READ BEFORE USING • Left over fertilizer can be spread under trees and Now You Are Ready To Put other high feeding areas without showing "edge of Material In The Hopper spread" lines. WARNING: Avoid Injury! Chemicals can be Tip: When not spreading, and if pushing the spreader dangerous.
-
Page 10: Troubleshooting
ACCUWAY® - What It Does The Accuway® Spread Pattern Equalizer Balances the spread pattern - Bulls Eye - Dead to the Center of the Spreader. All products. All spreading conditions. Skewing is eliminated. Does not change the spread width. ACCUWAY® - How It Works Accuway®... - Page 11 NOTE: Dial Settings Are Approximate Only ! Dial Settings Dial Settings Full Rate Half Rate Lbs. per Once Over Twice Over Product Particle Size 1000 sq. ft. Fine Pellets Mixed Fine Pellets Small Pellets Nitrogen Pellets Medium Size Medium Pellets And Granuals Large Heavy Pellets...
-
Page 12: Year Limited Warranty
For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase.
Need help?
Do you have a question about the S40 Series and is the answer not in the manual?
Questions and answers