Table of Contents
Advertisement
Item
[DHCP]
[IP ADDRESS]
[SUBNET MASK]
[DEFAULT GATEWAY]
[PRIMARY DNS]
[SECONDARY DNS]
[DHCP SERVER]
[4G/LTE PROPERTY]
[APN]
[USER ID]
[PASSWORD]
[DIAL NO.]
[NETWORK TOOLS]
[LOG DISPLAY]
[STATUS DISPLAY]
[INITIALIZE]
[PING]
[DISPLAY SETUP]
Configure the settings for the details to be displayed in the viewfinder.
These menu items cannot be set when the thumbnail screen is displayed.
Item
[ZEBRA1 DETECT]
[ZEBRA2 DETECT]
[ZEBRA2]
[CENTER MARK]
[SAFETY MARK]
[SAFETY AREA]
[FRAME MARK]
[FRAME SIG]
[FRAME LVL]
Chapter 6 Menu Operations — Menu list
Sets whether to use automatic acquisition via DHCP when [INFRA] is selected in [TYPE].
[ENABLE]: Uses automatic acquisition.
[DISABLE]: Does not use automatic acquisition. Set [IP ADDRESS], [SUBNET MASK], [DEFAULT
GATEWAY], [PRIMARY DNS], and [SECONDARY DNS].
f Factory setting: [ENABLE]
Sets the IP address when [DISABLE] is selected in [DHCP].
f Factory setting: [192.168.0.1]
Sets the subnet mask when [DISABLE] is selected in [DHCP].
f Factory setting: [255.255.255.0]
Sets the default gateway when [INFRA] is selected in [TYPE] and [DISABLE] is selected in [DHCP].
f Factory setting: [192.168.0.254]
Sets the primary DNS server when [INFRA] is selected in [TYPE] and [DISABLE] is selected in [DHCP], or
when [ENABLE] is selected in [DHCP] and the primary DNS server cannot be obtained.
f Factory setting: [0.0.0.0]
Sets the secondary DNS server when [INFRA] is selected in [TYPE] and [DISABLE] is selected in [DHCP],
or when [ENABLE] is selected in [DHCP] and the primary DNS server cannot be obtained.
f Factory setting: [0.0.0.0]
Sets whether to use the DHCP SERVER function when [DIRECT] is selected in [TYPE] and the camera is
connected via wireless LAN.
[ENABLE]: Uses the DHCP SERVER function.
[DISABLE]: Does not use the DHCP SERVER function.
f Factory setting: [ENABLE]
Sets the APN (Access Point Name) provided by the provider.
Sets the user name provided by the provider.
Sets the password provided by the provider.
Sets the phone number. For details, refer to the manual of the provider you have contracted.
Displays the connection log.
Displays the network status.
Restores the network setting status to the factory settings.
Checks network connection using PING commands.
Sets the extraction level of zebra pattern 1.
[0%]...[109%]
f Factory setting: [70%]
Sets the extraction level of zebra pattern 2.
[0%]...[109%]
f Factory setting: [85%]
Sets on/off of zebra pattern 2 and selects the type.
[ON], [SPOT], [OFF]
f Factory setting: [SPOT]
Controls the center mark.
[1]: + (large)
[2]: Open center (large)
[3]: + (small)
[4]: Open center (small)
[OFF]: Does not display.
f Factory setting: [1]
Selects the type of frame for the safety zone marker.
[1]: Box
[2]: Corners
[OFF]: Does not display.
f Factory setting: [2]
Sets the size of the safety zone marker.
The constant ratio of length to width can be set in 1% increments.
[80%]...[100%]
f Factory setting: [90%]
Enables/disables frame marker.
[ON], [OFF]
f Factory setting: [OFF]
Sets frame marker aspect ratio.
[4:3], [13:9], [14:9], [1.85:1], [2.35:1]
f Factory setting: [4:3]
Sets the level of the outside of the frame marker.
[0]...[15]
f Factory setting: [15]
– 148 –
Description of settings
Description of settings
Advertisement
Table of Contents
