Table of Contents
Advertisement
Item
[SDI OUT2/IN SEL]
[HDMI OUT SIGNAL]
[GL IN/VIDEO OUT SEL]
[GENLOCK SETTING]
[GL PHASE]
[H PHASE]
[DOWNCON SETTING]
[DETAIL]
[H.DTL LEVEL]
[V.DTL LEVEL]
[DTL CORING]
[H.DTL FREQ]
[MON OUT ZEBRA]
[TC IN/OUT SEL]
[TC OUT]
[TC OUTPUT REF]
Chapter 6 Menu Operations — Menu list
Selects if the <SDI OUT2/IN> terminal is to be used as the <SDI OUT2> terminal or to be used as the
<SDI IN> terminal. This can be set when the main menu → [SYSTEM MODE] → [REC SIGNAL] is set to
[CAM].
[SDI OUT2]: Uses as the <SDI OUT2> terminal.
[SDI IN]: Uses as the <SDI IN> terminal.
f Factory setting: [SDI OUT2]
Selects the output video signal from the <HDMI> terminal.
[MON]: Outputs the signal from the monitor output.
[VF]: Outputs the same signal as the one from the viewfinder. Video format will be 1080i.
[SDI IN]: Outputs the signal input to the <SDI OUT2/IN> terminal. The video format is 1080i, 720P, 480P,
or 576P, in accordance with the setting in the main menu → [SYSTEM MODE] → [LINE&FREQ].
f Factory setting: [MON]
Audio is not output when it is set to [VF] or [SDI IN].
Selects if the <GL IN/VIDEO OUT> terminal to be used as the genlock input or to be used as the video
output.
[GENLOCK IN]: Uses as the genlock input.
[VIDEO OUT]: Uses as the video output.
f Factory setting: [VIDEO OUT]
When in HD (1080P, 1080i, 720P) mode, selects the output signal of phase to be locked to the signal input
to the <GL IN/VIDEO OUT> terminal.
[HD SDI]: Locks the HD SDI output signal to genlock input.
[COMPOSITE]: Locks the down-converted composite output signal (480i or 576i signal from <GL IN/
VIDEO OUT> terminal) to genlock input.
f Factory setting: [HD SDI]
Adjusts the horizontal phase when the phase is to be locked to the signal input to the <GL IN/VIDEO
OUT> terminal.
[−512]...[512]
f Factory setting: [0]
Turns detail function for the down converter output signal [ON]/[OFF].
[ON], [OFF]
The down converter output signal contains detail components set during HD signal processing.
This setting superimposes the detail components exclusive to down converter output to that signal.
f Factory setting: [ON]
Sets horizontal detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [8]
Sets vertical detail correction level for the down converter output signal.
[0]...[31]
f Factory setting: [4]
Sets the detail noise removal level.
[0]...[15]
f Factory setting: [1]
Selects the horizontal detail frequency.
[2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz]
f Factory setting: [3.5MHz]
Selects whether the zebra pattern is superimposed over the output video signals from the monitor output
terminals (<HDMI>, <SDI OUT2/IN>, and <GL IN/VIDEO OUT>).
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
The video signal output from the <SDI OUT1> terminal will be a candidate for selection when [MON
ZEBRA] is selected in the main menu → [IN/OUT SEL] → [SDI OUT1 ZEBRA].
Selects whether to use the <TC IN/OUT> terminal for input or for output.
[TC OUT]: Uses as output.
[TC IN]: Uses as input.
f Factory setting: [TC OUT]
Sets the type of time code output from the <TC IN/OUT> terminal.
[TCG]: Outputs the time code generator value of the camera at all times.
[TCG/TCR]: Outputs the time code generator value for camera image output, and the time code value of
the video being played back for video playback output.
f Factory setting: [TCG]
Sets the output delay of time code output from the <TC IN/OUT> terminal.
[RECORDING]: Outputs the recorded time code with no delay. This is used when performing simultaneous
recording on two cameras with the time code of this camera as the master.
[MON OUT]: Matches to output image.
f Factory setting: [MON OUT]
– 145 –
Description of settings
Advertisement
Table of Contents
