Table of Contents
Advertisement
During thumbnail and menu operation
Display
[AUTHENTICATION ERROR!]
[CANNOT ACCESS!]
[CANNOT CHANGE!]
[CANNOT DELETE!]
[CANNOT FORMAT!]
[CANNOT RE-CONNECT!]
[CANNOT REPAIR IN SELECTION!]
[CANNOT REPAIR!]
[CANNOT SAVE!][FILE NAME IN USE]
[CARD FULL!]
[COPY IMPOSSIBLE. TOO LARGE CLIP
CONTAINED!] [CLIP NAME:] (clip name)
[INVALID VALUE!]
[INVALID DELETE]
[LACK OF CAPACITY!]
[MISSING CLIP!]
[NO CARD!]
[NO COPY TO SAME CARD!]
[NO FILE!]
[NO INPUT!]
[NO SD CARD!]
[NOT SELECTED!]
[SAME CLIP IS SELECTED!]
[TOO MANY CLIPS!]
[UNKNOWN CONTENTS FORMAT!]
[UNKNOWN DATA!]
[USER CLIP NAME MODIFIED!]
[WRITE PROTECTED!]
[CANNOT OPERATE THIS MENU, WHILE
"REC DURING UPLOAD" ENABLED.]
During soft keyboard operation
Display
[AUTHENTICATION ERROR!]
[CANNOT CHANGE!]
[CANNOT SET!]
[INVALID VALUE!]
[CANNOT SET!]
[NO INPUT!]
[CANNOT SET!]
[RETRY PASSWORD IS DIFFERENT!]
Chapter 11 Maintenance — Warning system
Description
Manual authentication failed.
Data cannot be accessed due to a content defect or
some other reason.
For a clip with the
mark, where a thumbnail cannot
be generated, the thumbnail cannot be modified in the
text memo position.
The content versions do not match. Cannot delete.
A P2 card problem or some other reason prevents
formatting.
Clips cannot be remerged because either clips not
recorded across multiple P2 cards are selected or other
reasons.
Some of the selected clips cannot be repaired.
Content that cannot be repaired is selected.
A settings file of the same name exists on the SD
memory card.
The P2 card or SD memory card is full.
Files exceeding 4 GB cannot be copied to P2 memory
cards or microP2 memory card with 32 GB or smaller
capacity.
The data value you entered is invalid.
The clip recorded last cannot be deleted with the last
clip delete function.
There is not enough recording capacity left on the card.
Shot marks cannot be attached to the clips unless all
clips recorded over multiple P2 cards are present.
No P2 or SD memory card is inserted.
A clip cannot be copied to the card storing the original
clip.
The specified file does not exist.
No data is entered.
No SD memory card.
Attempted to delete without selecting clips.
Multiple instances of the same clip (copies) are included
in the clips selected.
Too many clips are selected.
This is a warning of the contents for the version that is
not supported by the camera.
You cannot write back only proxy recording clips from
the FTP server to the P2 card.
The metadata character code is invalid.
There is a problem with data in the file.
When adding a counter value to the clip name,
characters must be deleted.
The P2 card or SD memory card is write-protected.
The menu cannot be executed.
Description
Manual authentication failed.
An attempt is made to enter the [PERSON] item (user
who enters the memo) when there is no text memo.
The entered value is invalid.
There is not input to the software keyboard.
The re-entered password is different.
– 216 –
Behavior and cause
Enter the correct password.
Ensure the health of the media and the clips.
Correct the settings and content to enable display of the
thumbnail.
Match the device and contents version.
Check the P2 card.
Check the selected content.
Check the selected content.
Check the selected content.
Use another name to save the file.
Insert a card with free space available.
Copy to a microP2 memory card with 32 GB or larger
capacity.
Enter data within the normal range.
To close the dialog, press the [SET] button.
For details on conditions that clip cannot be deleted,
refer to "Final clip delete function" (page 108).
Insert a card with sufficient recording capacity.
Insert all P2 cards over which recording extended.
Insert the relevant media.
Copy the selected clip to a card that does not contain
the original clip.
Check the file.
Enter data and then set.
Insert an SD memory card.
Select clips to delete.
Multiple instances of the same clip (copies) cannot be
copied simultaneously. Remove instances of the same
clip from selected items.
Reduce the number of selected clips.
Match the device and content versions.
Write back (import) proxy recording clips to an SD
memory card.
The metadata character code is UTF-8. Enter valid
characters using a viewer.
Create the file again.
For the counter addition setting, the user clip name plus
the counter value can only contain up to 100 bytes.
Characters in the clip name are automatically deleted
when the total number of characters exceeds this limit.
Insert write-accessible media.
Set [DISABLE] in the main menu → [NETWORK
SETUP] → [FTP CLIENT SERVICE] → [REC DURING
UPLOAD] before execution.
Behavior and cause
Enter the correct password.
Enter the [TEXT] (text information) first.
Change the input value.
Enter the password.
Enter the correct reference password.
Advertisement
Table of Contents
