Panasonic PX380G-BS300 Operating Instructions Manual page 164

Corresponding button
<STOP> button
[SET03:MON OUT SETUP]
Sets the output setting of the <SDI OUT2/IN> terminal, the <HDMI> terminal, and the <GL IN/VIDEO OUT> terminal.
Corresponding button
<%/REW> button
<STOP> button
<FF/)> button
[SET04:LCD]
Sets the display settings of SmartUI.
Corresponding button
<FF/)> button
<PLAY/PAUSE> button
<RESET> button
<MONITOR SEL> button
Chapter 7 SmartUI operation — SmartUI menu list
[D.CON]
Sets the aspect for the down-conversion output signal in the
HD mode. This item is not displayed in the SD mode.
[OUT]
Sets whether to output from the <SDI OUT2/IN> terminal, the
<HDMI> terminal, and the <GL IN/VIDEO OUT> terminal.
When the remote control unit (AJ-RC10G), the extension control unit (AG-EC4G), or the remote operation panel (AK-HRP200G)
is connected, the signal is always output from the <GL IN/VIDEO OUT> terminal regardless of this setting.
[CHR]
Specifies whether characters are superimposed over the
output from the <SDI OUT2/IN> terminal, <HDMI> terminal, the
<GL IN/VIDEO OUT> terminal, and the <REMOTE> terminal.
f The video signal output from the <SDI OUT1> terminal will
be a candidate for selection when [MON CHAR] is selected
in the main menu → [IN/OUT SEL] → [SDI OUT1 CHAR].
This setting is disabled when the remote control unit (AJ-RC10G), the extension control unit (AG-EC4G), or the remote operation
panel (AK-HRP200G) is connected, and the setting on the remote control unit, the extension control unit, or the remote operation
panel will be applied.
[ZBR]
Specifies whether zebra pattern are superimposed over the
output from the <SDI OUT2/IN> terminal, <HDMI> terminal, the
<GL IN/VIDEO OUT> terminal, and the <REMOTE> terminal.
f This setting is not available when the setting menu on the
viewfinder is open.
f The video signal output from the <SDI OUT1> terminal will
be a candidate for selection when [MON ZEBRA] is selected
in the main menu → [IN/OUT SEL] → [SDI OUT1 ZEBRA].
[−]
Decreases the setting value of the selected item. Press and hold this button to continuously decrease the setting value.
[+]
Increases the setting value of the selected item. Press and hold this button to continuously increase the setting value.
[RST]
Resets the setting value of the selected item to its factory setting value.
[→]
Moves the item selection to the right. When the item selection moves to the right edge, it moves back to the left edge.
[BACK LIGHT]
Sets the luminance of SmartUI.
[CONTRAST]
Sets the contrast of SmartUI.
f The SmartUI screen may be hidden depending on the
setting value.
In such a case, press the <HOME> to return to the [HOME]
screen and hold down the <LIGHT> and <RESET> buttons.
The setting value of [CONTRAST] is reset to the factory
setting.
Setting details and setting value
[CROP]
Side-crop mode (Crops the left and right edges.)
[L.BOX]
Letterbox mode (Adds black bands at the top and bottom of
the image.)
[SQU]
Squeeze mode (Squeezes images horizontally.)
f Factory setting: [L.BOX]
Setting details and setting value
[ON], [OFF]
f Factory setting: [ON]
[ON], [OFF]
f Factory setting: [ON]
[ON], [OFF]
f Factory setting: [OFF]
Setting details and setting value
[1]...[5]
f Factory setting: [3]
[0]...[63]
f Factory setting: [33]
– 164 –