Table of Contents
Advertisement
Available languages
Available languages
Anti-Tip
Bracket
Range Foot
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Tape measure
■
Level
■
Phillips screwdriver
■
Flat-blade screwdriver
■
Parts supplied
Check that all parts are included.
3 - 10-32 hex nuts (attached to terminal block)
■
3 - Terminal lugs
■
Oven racks
■
2 - #12 x 1
/
" (4.1 cm) screws (for mounting anti-tip bracket)
5
■
8
Anti-tip bracket (taped inside upper oven with package
■
containing literature)
Anti-tip bracket must be securely mounted to back wall or
floor. Thickness of floor may require longer screws to anchor
bracket to subfloor. Longer screws are available from your
local hardware store.
Parts needed
If using a power supply cord:
A UL Listed power supply cord kit marked for use with ranges.
■
The cord should be rated at 250 V minimum, 40 A or
50 A that is marked for use with nominal 1
diameter connection opening and must end in ring terminals
or open-end spade terminals with upturned ends.
A UL Listed strain relief.
■
Check local codes. Check existing electrical supply. See the
"Electrical Requirements" section.
It is recommended that all electrical connections be made by
a licensed, qualified electrical installer.
2
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
INSTALLATION REQUIREMENTS
Wrench or pliers
■
3/8" (9.5 mm) nut driver
■
Hand or electric drill
■
1/8" (3.2 mm) drill bit
■
/
" (3.5 cm)
3
8
WARNING
Tip Over Hazard
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
It is the installer's responsibility to comply with installation
■
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the control panel.
To eliminate the risk of burns or fire by reaching over heated
■
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
Cabinet opening dimensions that are shown must be used.
■
Given dimensions are minimum clearances.
The floor anti-tip bracket must be installed. To install the
■
anti-tip bracket shipped with the range, see the "Install
Anti-Tip Bracket" section.
Grounded electrical supply is required. See the "Electrical
■
Requirements" section.
IMPORTANT: To avoid damage to your cabinets, check
■
with your builder or cabinet supplier to make sure that the
materials used will not discolor, delaminate or sustain other
damage. This range has been designed in accordance with
the requirements of UL and CSA International and complies
with the maximum allowable wood cabinet temperatures of
194°F (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD Part 280). When such
standard is not applicable, the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
Mobile home installations require:
When this range is installed in a mobile home, it must be
■
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.
Four-wire power supply cord or cable must be used in a
■
mobile home installation. The appliance wiring will need to
be revised. See the "Electrical Connection" section.
Advertisement
Table of Contents
