DFI G7S300-B User Manual
  1. Manuals
  2. Brands
  3. DFI Manuals
  4. Motherboard
  5. G7S300-B
  6. User manual

DFI G7S300-B User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
G7S300-B
System Board
User's Manual
935-G7S301-000G
A00200701

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G7S300-B and is the answer not in the manual?

Questions and answers

Related Manuals for DFI G7S300-B

Summary of Contents for DFI G7S300-B

  • Page 1 G7S300-B System Board User’s Manual 935-G7S301-000G A00200701...
  • Page 2 Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior writ- ten permission from the copyright holders. This publication is provided for informational purposes only.
  • Page 3 FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.

  • Page 4: Table Of Contents

    Table of Contents About this Manual................Warranty....................Static Electricity Precaution..............Safety Measures..................About the Package................Before Using the System Board............Chapter 1 - Introduction..............Specifications........................... Features.............................. Chapter 2 - Hardware Installation............ System Board Layout ......................System Memory.......................... CPU............................... Jumper Settings..........................Rear Panel I/O Ports......................

  • Page 5: About This Manual

    About this Manual An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click “User’s Manual”...

  • Page 6: Static Electricity Precaution

    Introduction Static Electricity Precautions It is quite easy to inadvertently damage your PC, system board, components or devices even before installing them in your system unit. Static electrical discharge can damage computer components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.

  • Page 7: About The Package

    Introduction About the Package The system board package contains the following items. If any of these items are missing or damaged, please contact your dealer or sales representative for assistance. The system board A user’s manual One IDE cable One FDD cable One Serial ATA data cable One Serial ATA power cable One bracket mounted with 1 serial port...

  • Page 8: Chapter 1 - Introduction

    Introduction Chapter 1 - Introduction Specifications Processor • Intel Prescott processor ® - Intel Pentium ® ® - Intel Pentium ® ® - Intel Celeron D ® - Hyper-Threading Technology - 800MHz/533MHz system data bus • Processor socket: Socket 775 Chipset •...
  • Page 9 Introduction Graphics • Graphics memory - Shares 1MB/4MB/8MB/16MB/32MB of the system memory in DOS mode - Uses Dynamic Video Memor y Technology (DVMT) in Windows mode • Graphics controller - Core frequency of 266MHz - 350MHz integrated 24-bit RAMDAC - Analog display up to 2048x1536 @ 60Hz refresh - 3D setup and render engine - Discrete, Triangles, Strips and fans - Per pixel perspective corrected texture mapping...
  • Page 10 Introduction I/O Connectors • 2 connectors for 4 additional external USB 2.0/1.1 ports • 1 connector for 1 external serial port • 1 Digital I/O connector • 1 Digital I/O power connector • 1 front audio connector for external line-out and mic-in jacks •...

  • Page 11: Features

    Introduction Features The Watchdog Timer function allows your watchdog timer application to regularly “clear” the system at the set time interval. If the system hangs or fails to function, it will reset at the set time interval so that your system will continue to operate.
  • Page 12 Introduction S/PDIF is a standard audio file transfer format that S/PDIF transfers digital audio signals to a device without having to be converted first to an analog format. This prevents the quality of the audio signal from degrading whenever it is converted to analog.
  • Page 13 Introduction The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 suppor ts 12Mb/second bandwidth while USB 2.0 suppor ts 480Mb/second bandwidth providing a marked improvement in device transfer speeds between your com- puter and a wide range of simultaneously accessible external Plug and Play peripherals.
  • Page 14 Introduction This function allows you to use a USB key- wake-on-USB board or USB mouse to wake up a system from the S3 (STR - Suspend To RAM) state. Important: If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the 5V_standby power source of your power sup- ply must support ≥...

  • Page 15: Chapter 2 - Hardware Installation

    Hardware Installation Chapter 2 - Hardware Installation System Board Layout...

  • Page 16: System Memory

    Hardware Installation Warning: Electrostatic discharge (ESD) can damage your system board, proces- sor, disk drives, add-in boards, and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protec- tion by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis.
  • Page 17 Hardware Installation The two DDR DIMM sockets on the system board are divided into 2 channels: Channel A - DDR 1 Channel B - DDR 2 The system board supports the following memory interface. Single Channel (SC) Data will be accessed in chunks of 64 bits (8B) from the memory channels.
  • Page 18 Hardware Installation Installing the DIMM A DIMM simply snaps into a DIMM socket on the system board. Pin 1 of the DIMM must correspond with Pin 1 of the socket. Notch Pin 1 1. Pull the “tabs” which are at the ends of the socket to the side. 2.

  • Page 19: Cpu

    Hardware Installation Overview The system board is equipped with a surface mount LGA 775 socket. This socket is exclusively designed for installing a LGA 775 packaged Intel CPU. Important: 1. Before you proceed, make sure (1) the LGA775 1. Before you proceed, make sure (1) the LGA775 1.
  • Page 20 Hardware Installation Important: The CPU socket must not come in contact with anything other than the CPU. Avoid unnecessary exposure. Remove the protective cap only when you are about to install the CPU. 4. The CPU socket comes with a cover that is attached with a re- movable protective cap.
  • Page 21 Hardware Installation 7. Now lift the cover. Cover 8. Position the CPU above the socket. The gold mark on the CPU must align with pin 1 of the CPU socket. Important: Handle the CPU by its edges and avoid touching the pins. Gold mark Pin 1 of the socket...
  • Page 22 Hardware Installation 9. Insert the CPU into the socket until it is seated in place. The CPU will fit in only one orientation and can easily be inserted without exerting any force. Important: Do not force the CPU into the socket. Forcing the CPU into the socket may bend the pins and damage the CPU.
  • Page 23 Hardware Installation 11. Push the lever down to lock the socket. The lever should hook onto the side tab to indicate that the CPU is completely se- cured in the socket. Installing the Fan and Heat Sink The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circulation across the CPU and heat sink, the CPU will overheat damaging both the CPU and system board.
  • Page 24 Hardware Installation 2. Place the heat sink on top of the CPU. The 4 studs around the heat sink which are used to secure the heat sink onto the sys- tem board must match the 4 mounting holes around the socket. Position each stud so that the groove faces the heat sink then push it down firmly until it clicks into place.

  • Page 25: Jumper Settings

    Hardware Installation Jumper Settings Clear CMOS Data Parallel 1-2 On: Normal (default) 2-3 On: Clear CMOS Data If you encounter the following, a) CMOS data becomes corrupted. b) You forgot the supervisor or user password. c) You are unable to boot-up the computer system because the processor’s ratio was incorrectly set in the BIOS.
  • Page 26 Hardware Installation 4. After powering-on the system, press <Del> to enter the main menu of the BIOS. 5. Select the Frequency/Voltage Control submenu then press <Enter>. 6. Set the processor’s ratio to its default setting or an appropriate clock ratio. Refer to the Frequency/Voltage Control section in chapter 3 for more information.
  • Page 27 Hardware Installation PS/2 Power Select 1-2 On: 5V 2-3 On: (default) 5V_standby Parallel JP1 is used to select the power of the PS/2 keyboard/mouse port. Selecting 5V_standby will allow you to use the PS/2 keyboard or PS/2 mouse to wake up the system. BIOS Setting Configure the PS/2 keyboard/mouse wake up function in the Integrated Peripherals submenu (“Super IO Device”...
  • Page 28 Hardware Installation USB Power Select Parallel USB 0-3 (JP2) 1-2 On: 5V 2-3 On: (default) 5V_standby USB 4-7 (JP3) 1-2 On: 5V 2-3 On: (default) 5V_standby JP2 and JP3 are used to select the power of the USB ports. Select- ing 5V_standby will allow you to use the USB keyboard or USB mouse to wake up the system.

  • Page 29: Rear Panel I/O Ports

    Hardware Installation Rear Panel I/O Ports PS/2 Parallel Mouse Mic-in USB 3 Line-in Line-out COM 1 USB 2 USB 0-1 PS/2 The rear panel I/O ports consist of the following: • PS/2 mouse port • PS/2 keyboard port • Parallel port •...
  • Page 30 Hardware Installation PS/2 Mouse and PS/2 Keyboard Ports PS/2 Mouse PS/2 Keyboard Parallel The onboard PS/2 mouse (Green) and PS/2 keyboard (Purple) ports are at location CN1 of the system board. The PS/2 mouse port uses IRQ12. If a mouse is not connected to this port, the system will reserve IRQ12 for other expansion cards.
  • Page 31 Hardware Installation • BIOS Setting: Configure the PS/2 wake up function in the Integrated Peripherals submenu (“Super IO Device” section) of the BIOS. Refer to chapter 3 for more information. Important: The 5V_standby power source of your power supply must sup- port ≥...
  • Page 32 Hardware Installation Parallel Port Parallel Parallel The standard parallel port (Burgundy) at location CN7 is for inter- facing your PC to a parallel printer. It supports SPP, ECP and EPP. Setting Function Allows normal speed operation but (Standard Parallel Port) in one direction only.
  • Page 33 Hardware Installation Serial Ports Parallel COM 1 COM 2 The system board is equipped with an onboard serial port (COM 1) at location CN4. It is also equipped with a 9-pin connector at location J16 (COM 2). The serial ports are RS-232 asynchronous communication ports with 16C550A-compatible UARTs that can be used with modems, serial printers, remote display terminals, and other serial devices.
  • Page 34 Hardware Installation VGA Port Parallel The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable connector to the VGA port (Blue) at location CN2. After you plug the monitor’s cable connector into the VGA port, gently tighten the cable screws to hold the connector in place.
  • Page 35 Hardware Installation RJ45 Fast-Ethernet Port Parallel The onboard RJ45 LAN port is at location CN6. This port allows the system board to connect to a local area network by means of a network hub. BIOS Setting Configure the onboard LAN in the Integrated Peripherals submenu (“Onboard Device”...
  • Page 36 Hardware Installation Universal Serial Bus Connectors USB 3 USB 2 Parallel USB 1 USB 0 USB 4-5 USB 6-7 The system board supports 8 USB 2.0/1.1 ports. USB allows data exchange between your computer and a wide range of simultane- ously accessible external Plug and Play peripherals.
  • Page 37 Hardware Installation Driver Installation You may need to install the proper drivers in your operating system to use the USB device. Refer to your operating system’s manual or documentation for more information. Refer to chapter 4 for more information about installing the USB 2.0 driver.
  • Page 38 Hardware Installation Audio Rear audio Parallel Mic-in Line-in Line-out Front audio Rear Audio The system board is equipped with 3 audio jacks at location CN3. A jack is a one-hole connecting interface for inserting a plug. • Mic-in Jack (Pink) This jack is used to connect an external microphone.
  • Page 39 Hardware Installation Front Audio The front audio connector (J2) allows you to connect to the line-out and mic-in jacks that are at the front panel of your system. Using the line-out and mic-in jacks will disable the rear audio’s line-out and mic- in functions.

  • Page 40: I/O Connectors

    Hardware Installation I/O Connectors CD-in Internal Audio Connector Parallel Ground Ground Left audio Right audio channel channel The CD-in connector (J4) is used to receive audio from a CD-ROM drive, TV tuner or MPEG card.
  • Page 41 Hardware Installation S/PDIF Connector Parallel SPDIF out SPDIF in The system board is equipped with a S/PDIF connector. One card- edge bracket, mounted with S/PDIF ports, may be provided with the system board. Install the card-edge bracket to an available slot at the rear of the system chassis then connect the audio cable con- nector to J6.
  • Page 42 Hardware Installation Speaker-Out Connector Parallel Audio Lout+ Audio Rout- Audio Audio Lout- Rout+ The speaker-out connector (J3) is used to connect external amplified speakers.
  • Page 43 Hardware Installation Floppy Disk Drive Connector Parallel The floppy disk drive connector supports two standard floppy disk drives. To prevent improper floppy cable installation, the floppy disk header has a keying mechanism. The 34-pin connector on the floppy cable can be placed into the header only if pin 1 of the connector is aligned with pin 1 of the header.
  • Page 44 Hardware Installation Serial ATA Connectors Parallel SATA 1 SATA 0 The two Serial ATA connectors are for connecting Serial ATA devices. Connect one end of the Serial ATA cable to J15 (SATA 0) or J14 (SATA 1) connector and the other end to your Serial ATA device. BIOS Setting Configure the Serial ATA drives in the Integrated Peripherals submenu (“OnChip IDE Device”...
  • Page 45 Hardware Installation IDE Disk Drive Connectors Parallel IDE 1 IDE 2 The two shrouded PCI IDE headers are used to interface four En- hanced IDE (Integrated Drive Electronics) disk drives. To prevent im- proper IDE cable installation, each shrouded PCI IDE header has a keying mechanism.
  • Page 46 Hardware Installation Note: Refer to your disk drive user’s manual for information about selecting proper drive switch settings. Adding a Second IDE Disk Drive When using two IDE drives, one must be set as the master and the other as the slave. Follow the instructions provided by the drive manufacturer for setting the jumpers and/or switches on the drives.
  • Page 47 Hardware Installation Cooling Fan Connectors Sense Power N. C. Ground Parallel CPU fan Sense Power Ground 2nd fan Power Sense Ground System fan Connect the CPU fan’s cable connector to the CPU fan connector (J11) on the system board. The system fan connector (J19) and 2nd fan connector (J22) are used to connect additional cooling fans.
  • Page 48 Hardware Installation Wake-On-LAN Connector Parallel Ground +5VSB Your LAN card package should include a cable. Connect one end of the cable to the wakeup header on the card and the other end to location J13 on the system board. The network will detect Magic Packet and assert a wakeup signal to power-up the system.
  • Page 49 Hardware Installation Power Connectors 1 3 1 +3.3VDC +3.3VDC -12VDC +3.3VDC Ground Ground Parallel +5VDC PS_ON# Ground Ground Ground +5VDC Ground Ground PWR_OK +5VSB +5VDC +5VDC +12VDC +12VDC +5VDC +3.3VDC Ground Ground Ground +12V +12V Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1.
  • Page 50 Hardware Installation Digital I/O and Digital I/O Power Connectors Parallel 5VDU +12V Digital I/O power Digital I/O The Digital I/O connector (J7) and Digital I/O power connector (J8) provide powering-on function to an external device that is connected to these connectors. The Digital I/O bus provides 8-bit write and 8- bit read.
  • Page 51 Hardware Installation Chassis Open Parallel Chassis signal Ground The system board supports the chassis intrusion detection function. Connect the chassis intrusion sensor cable from the chassis to J1. Whenever a chassis component has been removed, the sensor sends signal to J1 alerting you of a chassis intrusion event. Hardware Monitor for Windows The Hardware Monitor for Windows utility allows you to enable the chassis intrusion detection function.
  • Page 52 Hardware Installation DRAM Power LED and Standby Power LED DRAM Power LED Parallel Standby Power LED DRAM Power LED This LED will light when the system’s power is on. Standby Power LED This LED will light when the system is in the standby mode. Important: If the DRAM Power LED or Standby Power LED is lighted, you must power-off the system then turn off the power supply’s...
  • Page 53 Hardware Installation Front Panel Connectors Parallel RESET SW HDD-LED PWR-LED PWR-BTN HDD-LED - HDD LED This LED will light when the hard drive is being accessed. RESET SW - Reset Switch This switch allows you to reboot without having to power off the system.
  • Page 54 Hardware Installation Battery Parallel The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of power when the main power is shut off. Safety Measures • Danger of explosion if battery incorrectly replaced. • Replace only with the same or equivalent type recommend by the manufacturer.

  • Page 55: Chapter 3 - Bios Setup

    BIOS Setup Chapter 3 - BIOS Setup Award BIOS Setup Utility The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and pe- ripherals. In addition, the BIOS also contains codes for various ad- vanced features found in this system board.
  • Page 56 BIOS Setup Standard CMOS Features Use the arrow keys to highlight “Standard CMOS Features” then press <Enter>. A screen similar to the one below will appear. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Tuei, Dec 26 2006 Date <mm:dd:yy> Item Help Time <hh:mm:ss>...
  • Page 57 BIOS Setup IDE Channel 0 Master, IDE Channel 0 Slave, IDE Channel 1 Master and IDE Channel 1 Slave To configure the IDE drives, move the cursor to a field then press <Enter>. The following screen will appear. Phoenix - AwardBIOS CMOS Setup Utility IDE Channel 0 Master IDE HDD Auto-Detection Press Enter...
  • Page 58 BIOS Setup Capacity Displays the approximate capacity of the disk drive. Usually the size is slightly greater than the size of a formatted disk given by a disk checking program. Cylinder This field displays the number of cylinders. Head This field displays the number of read/write heads. Precomp This field displays the number of cylinders at which to change the write timing.
  • Page 59 BIOS Setup Video This field selects the type of video adapter used for the primary system monitor. Although secondary monitors are supported, you do not have to select the type. The default setting is EGA/VGA. EGA/VGA Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA, SVGA and PGA monitor adapters.
  • Page 60 BIOS Setup Extended Memory Displays the amount of extended memory detected during boot-up. Total Memory Displays the total memory available in the system.
  • Page 61 BIOS Setup Advanced BIOS Features The Advanced BIOS Features allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features Item Help...
  • Page 62 BIOS Setup CPU Feature This field is used to configure the CPU that is installed on the sys- tem board. Move the cursor to this field then press <Enter>. Phoenix - AwardBIOS CMOS Setup Utility CPU Feature Delay Prior to Thermal 16 Min Item Help Thermal Management...
  • Page 63 BIOS Setup Limit CPUID MaxVal The CPUID instruction of some newer CPUs will return a value greater than 3. Problems will occur only in certain operating systems. The default is Disabled because this problem does not exist in the Windows series operating systems. If you are using an operating system other than Windows, this problem may occur.
  • Page 64 BIOS Setup Hard Disk Boot Priority This field is used to select the boot sequence of the hard drives. Move the cursor to this field then press <Enter>. Use the Up or Down arrow keys to select a device then press <+> to move it up or <->...
  • Page 65 BIOS Setup CPU L1 and L2 Cache This field is used to speed up the memory access. Enable the exter- nal cache for better performance. Hyper-Threading Technology ® This field is used to enable the functionality of the Intel Processor with Hyper-Threading Technology and will appear only when using this processor.
  • Page 66 BIOS Setup Boot Up Floppy Seek When enabled, the BIOS will check whether the floppy disk drive in- stalled is 40 or 80 tracks. Note that the BIOS cannot distinguish be- tween 720K, 1.2M, 1.44M and 2.88M drive types as they are all 80 tracks.
  • Page 67 BIOS Setup Typematic Delay (Msec) This field allows you to select the delay between when the key was first depressed and when the acceleration begins. Security Option This field determines when the system will prompt for the password - everytime the system boots or only when you enter the BIOS setup.
  • Page 68 BIOS Setup Advanced Chipset Features Phoenix - AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD Item Help CAS Latency Time Menu Level Active to Precharge Delay DRAM RAS# to CAS# Delay DRAM RAS# Precharge Memory Frequency For Auto System BIOS Cacheable Enabled...
  • Page 69 BIOS Setup Manual If you want better performance for your system other than the one “by SPD”, select “Manual” then select the best option in fields that follow. CAS Latency Time This field is used to select the local memory clock periods. Active to Precharge Delay This item controls the number of DRAM clocks used for the DRAM parameters.
  • Page 70 BIOS Setup Memory Hole At 15M-16M In order to improve system performance, certain space in memory can be reserved for ISA cards. This memory must be mapped into the memory space below 16MB. When enabled, the CPU assumes the 15-16MB memory range is allocated to the hidden ISA address range instead of the actual system DRAM.
  • Page 71 BIOS Setup Integrated Peripherals Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals Press Enter OnChip IDE Device Item Help Press Enter Onboard Device Menu Level Super IO Device Press Enter ↑↓→← : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults...
  • Page 72 BIOS Setup IDE HDD Block Mode Enabled The IDE HDD uses the block mode. The system BIOS will check the hard disk drive for the maximum block size the system can transfer. The block size will depend on the type of hard disk drive. Disabled The IDE HDD uses the standard mode.
  • Page 73 BIOS Setup IDE Primary Master/Slave UDMA and IDE Secondary Master/ Slave UDMA These fields allow you to set the Ultra DMA in use. When Auto is selected, the BIOS will select the best available option after checking your hard drive or CD-ROM. Auto The BIOS will automatically detect the settings for you.
  • Page 74 BIOS Setup Onboard Device Move the cursor to this field and press <Enter>. The following screen will appear. Phoenix - AwardBIOS CMOS Setup Utility Onboard Device USB Controller Enabled Item Help Enabled USB 2.0 Controller Menu Level USB Keyboard Support Disabled AC97 Audio Auto...
  • Page 75 BIOS Setup AC97 Audio Auto Select this option when using the onboard audio codec. Disabled Select this option when using a PCI sound card. Onboard LAN Control This field is used to enable or disable the onboard LAN.
  • Page 76 BIOS Setup Super IO Device Move the cursor to this field and press <Enter>. The following screen will appear. Phoenix - AwardBIOS CMOS Setup Utility Super IO Device Power On Function BUTTON ONLY Item Help KB Power On Password Enter Menu Level Hot Key Power ON Ctrl-F1...
  • Page 77 BIOS Setup KB Power On Password Move the cursor to this field and press <Enter>. Enter your pass- word. You can enter up to 5 characters. Type in exactly the same password to confirm, then press <Enter>. The power button will not function once a keyboard password has been set in this field.
  • Page 78 BIOS Setup Parallel Port Mode The options are SPP, EPP, ECP and ECP+EPP. These apply to a standard specification and will depend on the type and speed of your device. Refer to your peripheral’s manual for the best option. Allows normal speed operation but in one direction only. “ECP (Extended Capabilities Port)”...
  • Page 79 BIOS Setup Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy. Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled Item Help ACPI Suspend Type S1(POS) Menu Level Auto x Run VGABIOS if S3 Resume User Define...
  • Page 80 BIOS Setup Run VGABIOS if S3 Resume When this field is set to Auto, the system will initialize the VGA BIOS when it wakes up from the S3 state. This can be configured only if the “ACPI Suspend Type” field is set to “S3(STR)”. Power Management This field allows you to select the type (or degree) of power saving by changing the length of idle time that elapses before the “Suspend...
  • Page 81 BIOS Setup Suspend Mode When the system enters the Suspend mode, the CPU and onboard peripherals will be shut off. HDD Power Down This is selectable only when the Power Management field is set to User Define. When the system enters the HDD Power Down mode according to the power saving time selected, the hard disk drive will be powered down while all other devices remain active.
  • Page 82 BIOS Setup Wake-Up By PCI Card Enabled This field should be set to Enabled only if your PCI card such as LAN card or modem card uses the PCI PME (Power Management Event) signal to remotely wake up the system. Access to the LAN card or PCI card will cause the system to wake up.
  • Page 83 BIOS Setup PnP/PCI Configurations This section shows how to configure the PCI bus system. It covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. Phoenix - AwardBIOS CMOS Setup Utility PnP/PCI Configurations Reset Configuration Data Disabled...
  • Page 84 BIOS Setup IRQ Resources Move the cursor to this field and press <Enter>. Set each system interrupt to either PCI/ISA PnP or Legacy ISA. Phoenix - AwardBIOS CMOS Setup Utility IRQ Resources IRQ-3 assigned to PCI Device Item Help IRQ-4 assigned to PCI Device Menu Level IRQ-5 assigned to...
  • Page 85 BIOS Setup PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Current System Temp Item Help Current CPU Temperature Menu Level Current SYSTEM FAN Speed Current CPU FAN Speed Current SECOND FAN Speed CPU (V) 1.5(V) 3.3(V) +12V VBAT(V) 5VSB (V)
  • Page 86 BIOS Setup Frequency/Voltage Control Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control CPU Clock Ratio Item Help Disabled Spread Spectrum Menu Level ↑↓→← : Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults The settings on the screen are for reference only.
  • Page 87 BIOS Setup Load Fail-Safe Defaults The “Load Fail-Safe Defaults” option loads the troubleshooting de- fault values permanently stored in the ROM chips. These settings are not optimal and turn off all high performance features. You should use these values only if you have hardware problems. Highlight this option in the main menu and press <Enter>.
  • Page 88 BIOS Setup Load Optimized Defaults The “Load Optimized Defaults” option loads optimized settings from the BIOS ROM. Use the default values as standard values for your system. Highlight this option in the main menu and press <Enter>. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features...
  • Page 89 BIOS Setup Set Supervisor Password If you want to protect your system and setup from unauthorized entry, set a supervisor’s password with the “System” option selected in the Advanced BIOS Features. If you want to protect access to setup only, but not your system, set a supervisor’s password with the “Setup”...
  • Page 90 BIOS Setup Set User Password If you want another user to have access only to your system but not to setup, set a user’s password with the “System” option se- lected in the Advanced BIOS Features. If you want a user to enter a password when trying to access setup, set a user’s password with the “Setup”...
  • Page 91 BIOS Setup Save & Exit Setup When all the changes have been made, highlight “Save & Exit Setup” and press <Enter>. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password...
  • Page 92 BIOS Setup Exit Without Saving When you do not want to save the changes you have made, high- light “Exit Without Saving” and press <Enter>. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals...

  • Page 93: Updating The Bios

    BIOS Setup Updating the BIOS To update the BIOS, you will need the new BIOS file and a flash utility, AWDFLASH.EXE. Please contact technical support or your sales representative for the files. 1. Save the new BIOS file along with the flash utility AWDFLASH.EXE to a floppy disk.
  • Page 94 BIOS Setup 6. The following will appear. Do You Want to Save BIOS (Y/N) This question refers to the current existing BIOS in your system. We recommend that you save the current BIOS and its flash utility; just in case you need to reinstall the BIOS. To save the current BIOS, press <Y>...

  • Page 95: Chapter 4 - Supported Softwares

    Supported Software Chapter 4 - Supported Software Drivers, Utilities and Software Applications The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board. Inser t the CD into a CD-ROM drive. The autorun screen (Mainboard Utility CD) will appear.
  • Page 96 Supported Software Intel Chipset Software Installation Utility The Intel Chipset Software Installation Utility is used for updating ® Windows INF files so that the Intel chipset can be recognized and configured properly in the system. To install the utility, click “Intel Chipset Software Installation Utility” on the main menu.
  • Page 97 Supported Software 4. Go through the readme document for system requirements and installa- tion tips then click Next. 5. Setup currently installing the driver. 6. Click “Yes, I want to restar t my computer now” then click Finish. Restarting the system will allow the utility to take effect.
  • Page 98 Supported Software Intel Graphics Drivers To install the driver, click “Intel Graphics Drivers” on the main menu. 1. Setup is now ready to install the graphics driver. Click Next. 2. Read license agreement then click Yes. 3. Follow the prompts on the screen to complete installation.
  • Page 99 Supported Software Audio Drivers To install the driver, click “Audio Drivers” on the main menu. 1. Setup is now ready to install the audio driver. Click Next. 2. Setup is intalling and configuring the new soft- ware installation. 3. Click “Yes, I want to restar t my computer now”...
  • Page 100 Supported Software USB 2.0 Drivers To install the driver, click “USB 2.0 Drivers” on the main menu. Go through the document for system requirements and installation notes. ® The chipset does not support USB 2.0 drivers for Windows 98 SE and ®...
  • Page 101 Supported Software LAN Drivers To install the driver, click “LAN Drivers” on the main menu. 1. Setup is now ready to install the LAN driver. Click Next. 2. Click Install to begin the installation. 3. Setup is currently installing the driver.
  • Page 102 Supported Software 4. After completing installa- tion, click Finish to exit setup.
  • Page 103 Supported Software Hardware Monitor for Windows The system board comes with the Hardware Monitor for Windows utility. This utility is capable of monitoring the system’s temperature, fan speed, voltage, etc. and allows you to manually set a range (Highest and Lowest Limit) to the items being monitored.
  • Page 104 Supported Software 3. Click Next to add the program icon to the Program Folder. 4. Installation has been completed. Click Finish. 5. Click Yes if you want to create Hardware Doctor shortcut at your desktop.
  • Page 105 Supported Software 6. Click “Yes, I want to restar t my computer now” then click Finish. Restarting the system will allow the driver to take effect.
  • Page 106 Supported Software Microsoft DirectX 9.0C Driver To install, click “Microsoft DirectX 9.0C Driver” on the main menu. 1. Click “I accept the agree- ment” then click Next. 2. You are now ready to in- stall DirectX. Click Next. 3. Click Finish. Reboot the system for DirectX to take effect.

  • Page 107: Installation Notes

    Supported Software Installation Notes ® ® 1. "Autorun" ONLY supports the Windows 2000 and Windows XP operating systems. If after inserting the CD, "Autorun" did not automatically start (which is, the Main Board Utility CD screen did not appear), please go directly to the root directory of the CD and double-click "Setup".

  • Page 108: Appendix A - Enabling Hyper-Threading Technology

    Enabling Hyper-Threading Technology Appendix A - Enabling Hyper-Threading Technology Enabling Hyper-Threading Technology To enable the functionality of the Hyper-Threading Technology, please follow the requirements and steps below. Basically, the following ® ® presumes that you have already installed an Intel Pentium Processor with Hyper-Threading Technology.
  • Page 109 Enabling Hyper-Threading Technology Click the General tab. The processor shown under Computer should resemble the one shown below. Now click the Hardware tab then click Device Manager. The items shown under Computer and Processors should resemble the ones shown below.
  • Page 110 Enabling Hyper-Threading Technology Lastly, press the <Ctr l> <Alt> and <Del> keys simultaneously. The Windows Task Manager dialog box will appear. Click the Performance tab. The diagram under CPU Usage History should resemble the one shown below.

  • Page 111: Appendix B - Watchdog Timer

    Watchdog Timer Appendix B - Watchdog Timer Watchdog Timer The following parameters are references for setting the time interval of the Watchdog Timer function. The system will regularly be “cleared” according to the set time interval. If the system hangs or fails to function, it will also reset according to the time interval so that your system will continue to operate.

  • Page 112: Appendix C - System Error Messages

    System Error Message Appendix C - System Error Message When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in the information box at the bottom.
  • Page 113 System Error Message setting than indicated in Setup. Determine which setting is correct, either turn off the system and change the jumper or enter Setup and change the VIDEO selection. FLOPPY DISK(S) fail (80) Unable to reset floppy subsystem. FLOPPY DISK(S) fail (40) Floppy type mismatch.

  • Page 114: Appendix D - Troubleshooting

    Troubleshooting Appendix D - Troubleshooting Troubleshooting Checklist This chapter of the manual is designed to help you with problems that you may encounter with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple causes.
  • Page 115 Troubleshooting The picture seems to be constantly moving. 1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync. 2. Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display. 3.
  • Page 116 Troubleshooting Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootable (first) hard drive is configured as Master and the second hard drive is configured as Slave.
  • Page 117 Troubleshooting Serial Port The serial device (modem, printer) doesn’t output anything or is outputting garbled characters. 1. Make sure that the serial device’s power is turned on and that the device is on-line. 2. Verify that the device is plugged into the correct serial port on the rear of the computer.

Table of Contents