Digital Watchdog MEGAPIX PANO DWC-PZ21M69T Quick Start Manual

Quick Start Guide
DWC-PZ21M69T
Default Login Information
Username: admin Password: admin
WHAT'S IN THE BOX
Quick Screw &
manual & plastic
1
Download anchor –
Screw & Quick Manual &
Screw & Quick Manual &
Torx Wrench Torx Wrench Plastic Anchor-4pcs Plastic Anchor-4pcs Download Guide Download Guide
guide 4pcs
Screw &
Screw & Quick Manual & Torx Wrench Plastic Anchor-4pcs
Screw & Quick Manual &
Plastic Anchor-4pcs Torx Wrench Plastic Anchor-4pcs Download Guide Download Guide
Template Torque
1
sheet wrench
Moisture absorber - 2pcs
Template Sheet Waterproof cap & Gasket Torx Wrench
Moisture & Absorber Guide
absorber - Water-
2pcs & 1 Set proof cap
Absorber & Gasket
Moisture absorber - 2pcs Moisture absorber - 2pcs
guide
Template Sheet Waterproof cap & Gasket Waterproof cap & Gasket
& Absorber Guide Moisture absorber - 2pcs
& Absorber Guide Moisture absorber - 2pcs
Template Sheet Waterproof cap & Gasket Template Sheet
& Absorber Guide
& Absorber Guide
Poe injector
and 1
Power cable
Template Sheet
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
'Search by Product' search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click 'Search'. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
digital-watchdog.com
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
STEP 1 – PREPARING TO MOUNT THE
CAMERA
1. Mounting surface must withstand three times the weight of
the camera.
2. Do not let the cables get caught in improper places or the electric
line cover to be damaged. This may cause a short or fire.
3. CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric shock do
not perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power
Supply Unit marked "Class 2" or "LPS" or "PS2" and rated 12 Vdc,
1800 mA min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with
the output evaluated as a Limited Power Source as
defined in UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as
defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
8. Install the moisture packet at the top of the camera's cover.
a. Remove the moisture absorber from the packaging.
b. Cut the card and folder along the dotted line.
1 Set
c. Place the moisture absorber at the top of the camera's cover,
Quick Manual &
according to the diagram below.
Download Guide
1
Screw & Quick Manual &
Plastic Anchor-4pcs Download Guide
1 Set
Waterproof cap & Gasket
Absorbers attachment point
Moisture absorber - 2pcs
Waterproof cap & Gasket
& Absorber Guide
9. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
STEP 2 – POWERING THE CAMERA
Connect the camera to the PoE injector included in the box.
Connect the PoE injector to an adequate power source. See table
below for power source requirements. Refer to the user manual
for more options to power up the camera.
Power requirements Power consumption
DC12V, PoE IEEE 802.3at PoE+ DC12V : 21.5W
class 4 (High power PoE PoE IEEE802.3at Class4:
injector included) 23.2W
power cable,
connected to
adequate
power source.
Ethernet
cable
PoE
Injector
Ethernet Switch
NOTE: When using the PoE+ injector, do not connect the PoE
injector to the PoE/PoE+ switch or PoE/PoE+ enabled
port of PoE/PoE+ switch.
STEP 3 – INSTALLING THE CAMERA
1. Once all cables are connected, secure the camera to the
mounting surface using the included screws.
2. To use the camera's water proof wiring:
a. Install the LAN cable into .
a
b. will be assembled to
a
b
b
a
with a 1/4 turn.
c. Thread tightly to .
c
b
NOTE:
When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
3. The camera's four individual sensors can be rotated and tilted to
adjust the camera's views. Max tilt and rotation:
- Rotation: 20º
- Tilt: 18º
4 . Assemble the dome cover over the camera body and detach the
protecting film to complete the installation.
Template Sheet
2 1
Template Sheet
2
2
3 3
4
5
6
7
c
Resetting the camera: To reset the camera, use the tip of a
paper clip or a pencil and press the reset button. Pressing the
button for five (5) seconds will initiate a camera-wide reset of
all the settings, including network settings.
Quick Start Guide
Reset Button