Digital Watchdog MegaPix Pano DWC-PZ21M69T Quick Start Manual

DWC-PZ21M69T
Username: admin Password: admin
WHAT'S IN THE BOX
Quick Manual & Screw & Plastic
Screw &
1 Set
Download Guide Torx Wrench Anchor – 4pcs Plastic Anchor-4pcs
Screw & Quick Manual &
Torx Wrench Plastic Anchor-4pcs Download Guide
Screw & Quick Manual &
Torx Wrench Plastic Anchor-4pcs Download Guide
Screw & Quick Manual &
Torx Wrench
Torx Wrench Plastic Anchor-4pcs Download Guide
Template Sheet 1 Set Torx Wrench
Moisture absorber - 2pcs
Template Sheet Waterproof cap & Gasket
& Absorber Guide
Moisture absorber - Waterproof cap
1 Set
2pcs & Absorber Guide & Gasket
Moisture absorber - 2pcs
Template Sheet
Moisture absorber - 2pcs
& Absorber Guide
Template Sheet Waterproof cap & Gasket
Moisture absorber - 2pcs
& Absorber Guide
Template Sheet Waterproof cap & Gasket
PoE Injector and & Absorber Guide
Template Sheet
1 Set
power cable
Attention: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper camera usage.
Tel: 866-446-3595 / 813-888-9555
Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday
Quick Start Guide
STEP 1 – PREPARING TO MOUNT THE CAMERA
1. Mounting surface must withstand three times the weight of the camera.
2. Do not let the cables get caught in improper places or the electric line cover to be damaged. This may cause a short or fire.
3. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.
4. For the installation process, remove the dome cover by loosening the screws on the dome. Use the wrench provided with the camera.
STEP 2 – POWERING THE CAMERA
Connect the camera to the PoE injector included in the box. Connect the PoE injector to an adequate power source. See table
below for power source requirements. Refer to the user manual for more options to power up the camera.
Power Requirements
DC12V, PoE IEEE 802.3at PoE+ class 4
(High power PoE injector included)
NOTE: When using the PoE+ injector, do not connect the PoE injector to the
PoE/PoE+ switch or PoE/PoE+ enabled port of PoE/PoE+ switch.
STEP 3 – INSTALLING THE CAMERA
1. To use the camera's water proof wiring:
Quick Manual & (1). Install the LAN cable into (a).
1 Set
Download Guide
(2). (b) will be assembled to (a) with a 1/4 turn.
Screw & Quick Manual &
Plastic Anchor-4pcs Download Guide
(3).
Thread (c) tightly to (b).
1 Set
Screw &
Quick Manual &
NOTE: When using the waterproof cap, crimp the RJ45 connector after
Torx Wrench Plastic Anchor-4pcs Download Guide
passing the cable through the waterproof cap.
1 Set
2. Your camera comes with a moisture absorber included in the package. This
Waterproof cap & Gasket
Moisture absorber - 2pcs absorber needs to be installed inside the camera, next to the lens, to prevent
Waterproof cap & Gasket
& Absorber Guide
moisture build-up on the camera's dome that reduces image quality.
(1).
Remove the moisture absorber from the packaging.
Moisture absorber - 2pcs
Template Sheet Waterproof cap & Gasket
& Absorber Guide (2). Follow the diagram to place the absorber in the appropriate location.
3. The camera's four individual sensors can be rotated and tilted to adjust the camera's views. Max tilt and rotation:
- Rotation: 20º
digital-watchdog.com - Tilt: 18º
4 . Assemble the dome cover over the camera body and detach the protecting film to complete the installation.
Power Consumption
power cable,
connected to
adequate
power source.
DC12V Max 21.5W
Ethernet
PoE Max 23.4W
cable
PoE
Injector
Ethernet Switch
c
b
a
Please attach 2 card type
absorbers to attachment
points as the picture.
4
5
6
7
Reset Button
To reset the camera, press the reset button. Pressing the button for five (5) seconds will initiate a
camera-wide reset of all the settings, including network settings.
Quick Start Guide
Template Sheet