Monogram ZIFS360NHRH Installation Instructions Manual
36” built-in all-refrigerators and all-freezers
Hide thumbs
Also See for ZIFS360NHRH:
- Owner's manual (20 pages) ,
- Installation instructions manual (52 pages)
Related Manuals for Monogram ZIFS360NHRH
Summary of Contents for Monogram ZIFS360NHRH
- Page 1 Installation Instructions 36” Built-In All-Refrigerators and All-Freezers monogram.com...
-
Page 2: Safety
This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance, 3 people are required for proper installation. For Monogram local service in your area, call 1.800.432-2737. For Monogram service in Canada, call 1.800.561.3344 For Monogram Parts and Accessories, call 1.877.959.8688. - Page 3 CONSIGNES DE SÉCURITÉ Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots « DANGER », «...
-
Page 4: Table Of Contents
Contents Safety 2, 3 Installation Instructions Tools, Hardware, Materials Instructions for Standard Installation 5-21 Grounding the Unit Planning Guide Step 1. Remove Packaging The Installation Space Step 2. Install Water Line Dimensions and Clearances Step 3. Install Side Panels Customization Basics Step 4. -
Page 5: Instructions For Standard Installation
Instructions for Standard Installation... -
Page 6: The Installation Space
Design Guide - Standard Installation DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35" Case Width 25-3/8" Case Depth * Shipping height. The product can be adjusted to fit into a cutout that is 84-1/2” max. height. Note that the top case *84"... - Page 7 Design Guide - Standard Installation CLEARANCES 25" 2" Min. to 15" 130° Door Wall Swing 130° Clearances for two products installed side-by-side These units are equipped with a 3-position door stop. with the same (left or right) door swing The factory set 115° door swing can be adjusted to 90° Allow 2”...
-
Page 8: Customization Basics
• Do not install the refrigerator in a location exposed to Optional Accessory Kits water (rain, etc.) or direct sunlight. • ZKHSS2: Monogram Tubular Stainless Steel handles • Install it on a floor strong enough to support it fully designed to fit 3/4” overlay panels. -
Page 9: 1/4" Framed Panel Dimensions
Design Guide - Standard Installation 1/4” FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to 5/16" the dimensions shown. The panels will slide into the frame Trim on the door and grille. Door Reveal If the custom panel is less than 1/4”... -
Page 10: Side Panels
Design Guide - Standard Installation SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the unit The ZUG2 unified grille panel kit provides for the will be exposed. The 1/4” side panels will slip into the installation of a framed or overlay grille panel. -
Page 11: 130° Door Swing
Design Guide - Standard Installation Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. Top View 130°... -
Page 12: Installation Instructions
Installation Instructions - Standard Installation TOOLS AND MATERIALS REQUIRED GROUNDING THE UNIT • Tin snips to cut banding WARNING Electrical Shock Hazard. • #2 Phillips screwdriver • Stepladder Failure to follow these instructions can result in death, • Drill and 1/2”, 3/16” bits fire, or electrical shock. -
Page 13: Step 1 Remove Packaging
Installation Instructions - Standard Installation STEP 1 REMOVE PACKAGING • The unit is secured to the skid WARNING Tip Over Hazard. with 4 slotted tie-down straps. Product is much heavier at the top than at the bottom Remove the four 5/16” bolts –... -
Page 14: Step 4. Anti-Tip Procedures
Installation Instructions - Standard Installation STEP 4 INSTALL ANTI-TIP BRACKET STEP 4 INSTALL ANTI-TIP BRACKET (cont.) WARNING • The anti-tip wall bracket has a series of holes. Select 2 Tip Over Hazard. holes that match with the located studs. Make sure the The unit is top-heavy and must be secured to prevent the holes selected are on the center of the studs. - Page 15 Installation Instructions - Standard Installation STEP 4 INSTALL ANTI-TIP BRACKET (cont.) Install Wall Toggles: Install Screws and Bolts: The wall toggles and bolts can be ordered as Service Kit • Have someone hold the wall bracket centered in place #WR49X10193. Wall toggles are installed in the drywall with each of the holes aligned with the correct opening in and metal studs for stability.
- Page 16 Installation Instructions - Standard Installation STEP 4 INSTALL ANTI-TIP BRACKET (cont.) Remove Grilles for Access to Anti-Tip Locking Hooks Power Cord Locate the power cord inside the left cavity. If it has Fresh Food Unit not been adjusted so the plug is easily accessible, do •...
-
Page 17: Step 5 Level Unit
Installation Instructions - Standard Installation STEP 5 LEVEL UNIT STEP 6 SECURE UNIT TO WALL All models have 4-point leveling. The front is supported • The “L” rods can be found in the upper left and right by leveling legs; the rear is supported by adjustable corners of the unit in the access compartment. -
Page 18: Step 7 Adjust Door Swing
Installation Instructions - Standard Installation STEP 7 ADJUST DOOR SWING STEP 8 INSTALL GRILLE PANEL NOTE: This appliance has a 3-position door stop. When • Raise the access panel to the stop position. space does not allow the door to swing open fully to 115°, you may change the door swing to a 90°... -
Page 19: Step 9 Install Framed Panels
Installation Instructions - Standard Installation STEP 9 INSTALL FRAMED PANELS Right hand models shown. Use the same instructions for left hand models. IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 10A. Handle Door Trim Trim Door Use Front Holes to Secure Trim Use Rear Holes to Secure Handle... -
Page 20: Step 9A Install Overlay Panels
Installation Instructions - Standard Installation STEP 9A INSTALL OVERLAY PANELS Right hand models shown. Use the same instructions for left hand models. Door Trim Handle Trim Door Move Forward For 3/4" Panel Use Front Holes to Secure Handle Use Rear Holes to Secure Trim Supplied handle shown in the overlay panel position. -
Page 21: Step 10 Connect Water Supply
Installation Instructions - Standard Installation STEP 11 START ICEMAKER STEP 10 CONNECT WATER SUPPLY (FREEZER MODELS ONLY) (FREEZER MODELS ONLY) Icemaker House Freezer Water Supply Water Supply Power Feeler Arm Switch • Locate and bring the tubing to the front of the cabinet. •... -
Page 22: Instructions For Flush Installation
Instructions for Flush Installation... -
Page 23: The Installation Space
Design Guide - Flush Installation DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35" 39” Case Width Finished Width 25-3/8" Case Depth 4-5/16” Wall View * Shipping height. The product can be adjusted 5-1/2” to fit into a cutout that is 85” max. height. Use Electrical 9”... -
Page 24: Custom Handle Design Guide
Design Guide - Flush Installation CLEARANCES 4" Min. to Wall 1" 15" 15" 115° Door 115° Door Min. to Min. to 90° Door Swing Swing Swing Wall Wall 38-3/4" These units are equipped with a 3-position door stop. Clearances for Multiple Single Door Installations The factory set 115°... -
Page 25: 1/2" Overlay Panel Dimensions
Design Guide - Flush Installation 1/2” OVERLAY PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be Door 1/2" secured to a 1/4” thick backer panel which slides into the Overla trim. -
Page 26: 3/4" Decorative Panel Dimensions
Design Guide - Flush Installation 3/4” DECORATIVE PANEL DIMENSIONS IMPORTANT NOTE: Maximum total weight for the assembled panels: For a more custom appearance, overlay panels may be • • Door panel – 67 lbs. Grille Panel – 18 lbs. installed to give a flush appearance with surrounding cabinets. -
Page 27: 3/4" Raised Door Panel Routing
Design Guide - Flush Installation 3/4” RAISED DOOR PANEL ROUTING For 3/4” raised door panel, routing is required. The router depth is 1/4” all the way around the panel back. Additional panel width reductions are required per the diagrams below. This will create a “picture frame” routing that will slide onto the attached door trim. -
Page 28: 3/4" Raised Grille Panel Routing
Design Guide - Flush Installation 3/4” RAISED GRILLE PANEL ROUTING For 3/4” raised grille panel, routing is required. The router depth is 1/4” all the way around the panel back. Additional panel width reductions are required per the diagrams below. This will create a “picture frame” routing that will slide onto the attached grille trim. -
Page 29: Side Panels
Design Guide - Flush Installation SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be 24" The ZUG2 unified grille panel kit provides for the used whenever the installation of a framed or overlay grille panel. sides of the unit will be exposed. -
Page 30: Installation Instructions
Installation Instructions - Flush Installation TOOLS AND MATERIALS REQUIRED GROUNDING THE UNIT • Tin snips to cut banding WARNING Electrical Shock Hazard. • #2 Phillips screwdriver • Stepladder Failure to follow these instructions can result in death, • Drill and 1/2”, 3/16” bits fire, or electrical shock. -
Page 31: Step 1 Remove Packaging
Installation Instructions - Flush Installation STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. Product is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only. Risque de basculement AVERTISSEMENT Le produit est beaucoup plus lourd en haut qu’en bas. -
Page 32: Step 4 Install Case Trim
Installation Instructions - Flush Installation STEP 4 INSTALL CASE TRIM STEP 5 INSTALL ANTI-TIP BRACKET (cont.) The unit arrives with case trim for standard installation attached. Flush installation case trim is provided. Remove • The kit supplied with the unit contains 2 lag bolts and 4 the factory installed case trim. - Page 33 Installation Instructions - Flush Installation STEP 5 INSTALL ANTI-TIP BRACKET (cont.) • Mark an additional hole at each end of the bracket. If one Install Screws and Bolts: of the studs is closer to the end of the bracket, mark an •...
-
Page 34: Step 6 Level Unit
Installation Instructions - Flush Installation STEP 5 INSTALL ANTI-TIP BRACKET (cont.) Remove Grilles for Access to Anti-Tip Locking Hooks Power Cord Fresh Food Unit Locate the power cord inside the left cavity. If it has not • Open the access door. been adjusted so the plug is easily accessible, do so now. -
Page 35: Step 7 Adjust Door Swing
Installation Instructions - Flush Installation STEP 7 ADJUST DOOR SWING STEP 8 INSTALL GRILLE PANEL NOTE: This appliance has a 3-position door stop. When • Raise the access panel to the stop position. space does not allow the door to swing open fully to 115°, you may change the door swing to a 90°... -
Page 36: Step 9 Install Overlay Panels
Installation Instructions - Flush Installation STEP 9 INSTALL OVERLAY PANELS Custom Handles • Custom handles must be used for flush installation. The handle must be properly secured to the overlay panel before sliding the panel into the trim. • The cabinet manufacturer will supply the custom handle and hardware. -
Page 37: Step 10 Connect Water Supply
Installation Instructions - Flush Installation STEP 10 CONNECT WATER SUPPLY STEP 11 START ICEMAKER (FREEZER MODELS ONLY) (FREEZER MODELS ONLY) Icemaker House Freezer Water Supply Water Supply Power Feeler Arm Switch • Locate and bring the tubing to the front of the cabinet. •... -
Page 38: Instructions For Stainless Steel Installation
Instructions for Stainless Steel Installation... -
Page 39: The Installation Space
Design Guide - Stainless Steel Installation DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 25-3/8" Framed Models 35" 25-3/4" Stainless Steel Models Case Width Case Depth * Shipping height. The product can be adjusted to fit into a cutout that is 84-1/2” max. height. *84"... - Page 40 Design Guide - Stainless Steel Installation CLEARANCES 25" 2" Min. to 15" 130° Door Wall Swing 130° Clearances for two products installed side-by-side These units are equipped with a 3-position door stop. with the same (left or right) door swing The factory set 115°...
-
Page 41: Customization Basics
• Install it on a floor strong enough to support it fully Stainless Steel wrapped models have wrapped doors loaded. and grille panel, beveled edges, and tubular stainless steel handles that coordinate with other Monogram appliances. These models are shipped ready for installation. Optional Accessory Kits •... -
Page 42: 130° Door Swing
Design Guide - Stainless Steel Installation Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips. Top View 130°... -
Page 43: Installation Instructions
Installation Instructions - Stainless Steel Installation GROUNDING THE UNIT TOOLS AND MATERIALS REQUIRED • Tin snips to cut banding WARNING Electrical Shock Hazard. • #2 Phillips screwdriver • Stepladder Failure to follow these instructions can result in death, fire, or electrical shock. •... -
Page 44: Step 1 Remove Packaging
Installation Instructions - Stainless Steel Installation STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. Product is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only. Risque de basculement AVERTISSEMENT Le produit est beaucoup plus lourd en haut qu’en bas. - Page 45 Installation Instructions - Stainless Steel Installation STEP4 INSTALL ANTI-TIP BRACKET (cont.) • The kit supplied with the unit contains 2 lag bolts and 4 Wall Bracket toggles with bolts. The wall bracket will be attached to Center the wall in 4 places. •...
- Page 46 Installation Instructions - Stainless Steel Installation STEP 4 INSTALL ANTI-TIP BRACKET (cont.) Remove Grilles for Access to Anti-Tip Locking Hooks • Gently pull back at the ends of the plastic straps to make the channel rest flush behind the wall. Fresh Food Unit •...
-
Page 47: Step 4. Anti-Tip Bracket
Installation Instructions - Stainless Steel Installation STEP 4 INSTALL ANTI-TIP BRACKET STEP 5 LEVEL UNIT (cont.) All models have 4-point leveling. The front is supported Move Unit into Final Position by leveling legs; the rear is supported by adjustable • Move appliance toward its final installed location. wheels. -
Page 48: Step 6 Secure Unit To Wall
Installation Instructions - Stainless Steel Installation STEP 7 ADJUST DOOR SWING STEP 6 SECURE UNIT TO WALL NOTE: This appliance has a 3-position door stop. When • The “L” rods can be found in the upper left and right space does not allow the door to swing open fully to corners of the unit in the access compartment. -
Page 49: Step 8 Connect Water Supply
Installation Instructions - Stainless Steel Installation STEP 9 START ICEMAKER STEP 8 CONNECT WATER SUPPLY (FREEZER MODELS ONLY) (FREEZER MODELS ONLY) Icemaker House Freezer Water Supply Water Supply Power Feeler Arm Switch • Locate and bring the tubing to the front of the cabinet. •... - Page 50 Notes...
- Page 51 Notes...
- Page 52 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.432-2737. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.