Table of Contents
Advertisement
Note
f The single link is a setting to display one image with one input signal. The dual link is a setting to display one image with two input signals.
The quad link is a setting to display one image with four input signals.
f [SDI LINK] is fixed to [SINGLE] in the following cases.
g When the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] is set to anything other than [OFF]
g When the [MULTI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF] and displaying the four-screen display
f The [SDI LINK] setting cannot be changed when the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE]
is set as the combination used for the SDI input of the Interface Board.
f When [SDI LINK] is set to [AUTO], use the same format for the signal to be input to the <SDI 1 IN>/<SDI 2 IN/1 OUT>/<SDI 3 IN>/<SDI 4
IN/3 OUT> terminals. If different format signal is input to even one terminal, currently displayed image may not be projected correctly.
f [SDI MAPPING] and [3G-SDI MAPPING] cannot be set when [SDI LINK] is set to [AUTO].
f The content set is displayed in [SDI LINK SETTINGS].
Setting [RESOLUTION] in [SLOT IN] (SDI input)
1)
Press as to select [SLOT IN].
2)
Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3)
Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and
press the <ENTER> button.
f The [SINGLE LINK SETTING] screen, the [DUAL LINK SETTING] screen, or the [QUAD LINK SETTING]
screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] or [QUAD LINK SETTING] is selected.
4)
Press as to select [SDI1], [SDI2], [SDI3], or [SDI4], and press the <ENTER> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5)
Press as to select [RESOLUTION], and press the <ENTER> button.
f The [RESOLUTION] screen is displayed.
6)
Press as to select an item, and press the <ENTER> button.
f Select [AUTO], [720x480i], [720x576i], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF],
[2048x1080p], [3840x2160p], or [4096x2160p] when SDI1 input or SDI3 input is selected for [SINGLE LINK
SETTING].
f Select [AUTO], [720x480i], [720x576i], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], or
[2048x1080p] when SDI2 input or SDI4 input is selected for [SINGLE LINK SETTING].
f Select [AUTO], [1920x1080i], [1920x1080p], [1920x1080sF], [2048x1080p], [3840x2160p], or [4096x2160p]
when [DUAL LINK SETTING] is selected.
f Select [AUTO], [3840x2160p], [3840x2160sF], or [4096x2160p] when [QUAD LINK SETTING] is selected.
Setting [4K DIVISION] in [SLOT IN] (SDI input)
Set the transmission method in the 4K division when 4K image is displayed with SDI input.
1)
Press as to select [SLOT IN].
2)
Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3)
Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and
press the <ENTER> button.
f The [SINGLE LINK SETTING] screen, the [DUAL LINK SETTING] screen, or the [QUAD LINK SETTING]
screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] or [QUAD LINK SETTING] is selected.
4)
Press as to select [SDI1] or [SDI3], and press the <ENTER> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5)
Press as to select [4K DIVISION].
6)
Press qw to switch the item.
f The items will switch each time you press the button.
132 - ENGLISH
Chapter 4 Settings — [DISPLAY OPTION] menu
Advertisement
Table of Contents
