Contents Introduction Product Specification Safety Instructions Explanation of Graphic Symbols Power Supply and Low Battery Operation: Basic Functions Operation: Advanced Functions Setting the Date Using the Scale with a Printer Using the Scale with Bluetooth EMC Guidance and Manufacturer’s Declaration Recommended Separation Distance Error Messages Manufacturer’s Declaration of Conformity...
Thank you for purchasing a Marsden professional medical scale. This is a precision Class III Weighing Instrument and considerate use will result in many years of accurate weighing. The scale has a maximum load capacity of 300kg which must not be exceeded.
Before putting the device into use, please read with care the information given in this user manual, which contains important instructions for proper installation, use and maintenance of the device. Marsden/the manufacturer shall not be liable for damages arising from failure to heed the following instructions: ...
This product must be disposed of at a communal collection point. Carefully read this operation manual before setup and commissioning, even if you are already familiar with Marsden scales. Transport and storage temperature limit indicating the upper and lower limit (transport and storage temperature on packaging).
Power Supply & Low Battery The indicator uses a rechargeable battery pack, or can be powered from the mains via the AC adaptor. Make sure the battery pack is installed in the battery box of the indicator. Alternatively, plug the AC adaptor (12V 1A) into the port on the side of the indicator.
Operation: Basic Functions Switching on the Scale Press the ON/OFF button firmly. The scale will first test all of the display segments. The scale will now show its current software version number. The scale will now go into weighing mode and should show 0.0 on the display.
Page 8
Switching off the Scale Press the ON/OFF button when the scale is turned on. The scale will now power down. Setting the Scale to Zero If for any reason the display shows a reading other than 0.0 when there is nothing on the scale it can be reset to zero.
Operation: Advanced Functions Hold Function Press the HOLD button once. Allow the patient to get on the scale. After a few seconds the scale will lock on the person’s weight. When the patient leaves the scale, the weight will remain on the display.
Page 10
Body Mass Index (BMI) Function In normal mode, press BMI to enter BMI mode. The display will show the last height entered and the extreme left digit will flash. Enter the height by using the numeric keys. Press ZERO to confirm the height.
Page 11
Tare and Pre-Set Tare Functions Press TARE for three seconds to enter Pre- set Tare setting mode. The display will show the last pre-set tare entered and the extreme left digit will flash. Enter the pre-set tare value by using the numeric keys, then press TARE again to confirm the value.
Setting the Date Press HOLD for three seconds to access the time setting mode. The time period digit that is flashing can be changed by entering the appropriate number using the numeric keys. The time period to be edited is selected by pressing HOLD. E.g.
Using the Scale with a Printer An optional Marsden external printer (model TP-2100) is available for all models. With the printer fitted, the patient’s weight, height, and BMI result can be printed. Once the person has been weighed and their BMI calculated, simply press PRINT to produce...
(procedure may vary depending on device or system) The scale will appear on the Bluetooth device list as “MARSDEN BT”. Connect your device to “MARSDEN BT”, and the scale is ready to transmit data wirelessly via Bluetooth. Page 14...
EMC Guidance and Manufacturer’s Declaration Guidance and manufacturer’s declaration – electromagnet emissions. The M-800 is intended for use in the electromagnetic environment specified below. The customer or user of this scale should ensure that it is used in such environment.
Page 16
recommended that this scale is powered from an uninterruptable power supply or a battery. Power frequency (50/60 3 A/m 3 A/m The scale’s power frequency Hz) magnetic field IEC magnetic fields should be at 61000-4-8 levels characteristic of a typical location in a typical commercial or hospital environment.
B) Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Recommended separation distance between portable and mobile RF communications equipment and the M-800. This scale is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
Error Messages Low Battery The scale’s alkaline AA type batteries are flat; please replace the batteries. Overload This indicates that the scale’s load sensor(s) have been overloaded. Reduce the loading and retry. Counting Error 1. The signal from the load cells is too high.
ROHS Compliance EU Directive 2011/65/EU restrict the use of the 6 substances below in the manufacture of specified types of electrical equipment. The product does not contain any of the restricted substances in concentrations and applications banned by the directive; and for components, the product is capable of being worked on at higher ...