Page 1 1662/ 1664 Barcode Scanner Set up barcodes included. Version 2.22...
Page 2 Also, you m ay visit our web sit e for m ore inform at ion. The CipherLab logo is a regist ered t radem ark of CI PHERLAB CO., LTD. All brand, product and service, and t radem ark nam es are t he propert y of t heir regist ered owners.
Page 3: For Canada
IMPORTANT NOTICES FOR USA This equipm ent has been t est ed and found t o com ply wit h t he lim it s for a Cla ss B digit al device, pursuant t o Part 15 of t he FCC Rules. These lim it s are designed t o provide reasonable prot ect ion against harm ful int erference in a resident ial inst allat ion.
Page 4 (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. (antennas are less than 20 cm of a person's body). Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils portables. (les antennes sont moins de 20 cm du corps d'une personne).
Page 5: For Hand-Held Product With Rf Functions
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS The 1662/ 1664 unit ( FCC I D: Q3N- 1662/ 1664) com plies wit h FCC radiat ion exposure lim it s set fort h for uncont rolled environm ent and m eet s t he FCC radio frequency ( RF) Exposure Guidelines in Supplem ent C t o OET65.
Page 6: Declaration Conformity
DECLARATION CONFORMITY...
Page 8: Release Notes
RELEASE NOTES Version Date Notes  Modified: Sym bologie s Su ppor t e d – GS1 Dat aBar Fam ily enabled 2.22 Oct . 08, 2019 by default ; UPCA Addon 2/ Addon 5 appended  Modified: Se t u p QR Code – QR Code lim it ed ...
Page 9  New: 5 .2 .2 M u lt iple Ch a r a ct e r s Su bst it u t ion  Modified: Appe n dix I - Fir m w a r e Upgr a de – Low bat t ery warning when t he scanner get s int o download m ode ...
Page 10  New: 1 .2 0 – Serial Num ber St am p 2.17 May 09, 2014  New: 1 .2 0 .1 – Separat or bet ween Serial Num ber and Dat a  New: 2 .1 .1 0 – BT HI D Slave/ Mast er Swit ching ...
Page 11 Apr. 10, 2012 Modified: 1.10 rem ove Reading Redundancy – Three t im es 2.00 Mar. 20, 2012 Add: 1662 m odel and Set Up Drivers License 1.03 Feb. 06, 2012 Add: Chapt er 6 Fields of Tim e St am p 1.02...
Page 12: Table Of Contents
I N TROD UCTI ON ..................1 Get Fam iliarized wit h 1662/ 1664 and 3610 ..........2 I nst all t he Bat t ery int o 1662/ 1664 ............2 Charge t he Bat t ery ................3 Charge t he Bat t ery via Charger ............
Page 13 1.7.5 Mult i- Barcode Mode ..............40 1.7.6 Cont inuous Mode ( 1662 Only) ............ 41 1.7.7 Alt ernat e Mode ( 1662 Only) ............41 1.7.8 Mult icode Mode ( 1664 Only) ............42 1.7.9 Release Mode ................43 1.8 Scanning Tim eout ................
Page 14 1662/1664 Barcode Scanner User Guide 1.18.1 Rest ore Syst em Default s ............55 1.18.2 Reset Connect ion ..............55 1.18.3 Disable Hardware Reset ............55 1.19 Mobile Phone/ Display Mode ............. 56 1.20 Serial Num ber St am p ..............56 1.20.1 Separat or bet ween Serial Num ber St am p and Dat a ......
Page 15 1662/1664 Barcode Scanner User Guide 2.6.1 Act ivat e USB HI D & Select Keyboard Type ........93 2.6.2 Keyboard Set t ings ..............95 2.6.3 I nt er- Charact er Delay .............. 101 2.6.4 I nt er- Funct ion Delay ............... 101 2.6.5 HI D Charact er Transm it Mode ...........
Page 16 1662/1664 Barcode Scanner User Guide 4.8 Triopt ic Code 39 ................138 4.9 Code 93 ..................139 4.9.1 Code Lengt h Qualificat ion ............140 4.10 Code 128 ................... 141 4.11 GS1- 128 ( EAN- 128) ..............142 4.11.1 Transm it Code I D ..............142 4.11.2 Field Separat or ( GS Charact er) ..........
Page 17 1662/1664 Barcode Scanner User Guide 4.21.1 Com posit e CC- A/ B ..............168 4.21.2 Com posit e CC- C ..............168 4.21.3 Com posit e TLC- 39 ..............169 4.21.4 UPC Com posit e Mode ............. 169 4.21.5 GS1- 128 Em ulat ion Mode for UCC/ EAN Com posit e Codes .... 170 4.21.6 Field Separat or ( GS Charact er) ..........
Page 18 6.6.2 Exam ple I I ................247 SPECI FI CATI ON S .................. 249 FI RM W ARE UPGRAD E ................251 How t o Upgrade 1662/ 1664 Firm ware ........... 251 Using 3610 ..................251 Use Direct USB Virt ual COM .............. 253 ®...
Page 19 1662/1664 Barcode Scanner User Guide Key St at us ..................268 Exam ple .................... 269 N UM ERAL SYSTEM S ................271 Decim al Syst em ................. 271 Hexadecim al Syst em ................272 ASCI I Table ..................273 Ent ering PI N Code for Aut hent icat ion ............. 274 Use Preset PI N ................
Page 20: Introduction
10 m et ers and a prolonged bat t ery life t o keep business running. 1662/ 1664 is a new ordering opt ion provided for adapt ing a advanced scan engine t o read bot h 1D and 2D barcodes.
Page 21: Get Familiarized With 1662/1664 And 3610
1662/1664 Barcode Scanner User Guide GET FAMILIARIZED WITH 1662/1664 AND 3610 INSTALL THE BATTERY INTO 1662/1664 1) Hold t he scanner face down in one hand, press t he bat t ery cover, and slide t he bat t ery cover.
Page 22: Charge The Battery
1) I nst all t he bat t ery t o 1662/ 1664. 2) Connect 1662/ 1664 t o host com put er or not ebook via t he USB cable. 3) The scanner LED will flash red during charging.
Page 23: Charge The Battery Via Charger
1662/1664 Barcode Scanner User Guide CHARGE THE BATTERY VIA CHARGER The bat t ery charger is provided for charging t he bat t ery out side of t he scanner. You m ay purchase t he charger separat ely. I t t akes approxim at ely 3 hours t o charge t he bat t ery t o full.
Page 24: Use 3610
USE 3610 The CipherLab Dongle ( 3610) is specifically designed for t he scanner t o com m unicat e wit h a host com put er cordless. The connect ion bet ween t he scanners and 3610 is m ade easy and reliable.
Page 25: Inside The Package
Support different scan m odes, including Aim ing Mode ( 1664 only) , Alt ernat e Mode Not e ( 1662 only) and Mult i- Barcode Mode  Program m able feedback via LED indicat or, beeper and vibrat or.
Page 26: Symbologies Supported
Refer t o Chapt er 4 Change Sym bology Set t ings for det ails of each sym bology. Symbologies Supported: Enable/Disable 1D Laser (1662) 2D (1664) Enabled Enabled Coda ba r...
Page 27 1662/1664 Barcode Scanner User Guide ( RSS) GS1 Dat aBar Truncat ed Enabled Enabled GS1 Dat aBar St acked Enabled GS1 Dat aBar St acked Om nidirect ional Enabled GS1 Dat aBar Lim it ed ( RSS Lim it ed)
Page 28: Quick Start
QUICK START The configurat ion of t he scanner can be done by reading t he set up barcodes cont ained in t his m anual or via t he ScanMast er soft ware. This sect ion describes t he procedure of configuring t he scanner by reading t he set up barcodes and provides som e exam ples for dem onst rat ion.
Page 29 1662/1664 Barcode Scanner User Guide Working Mode Upon powering up, t he scanner will t ry t o est ablish a connect ion wit h 3610 or a com put er wit h ® Bluet oot h wireless t echnology. Refer t o Chapt er 3 - Set up a WPAN Connect ion for det ails.
Page 30: Enter Configuration Mode
Quick Start ENTER CONFIGURATION MODE For t he scanner t o ent er t he configurat ion m ode, read t he " Ent er Set up" barcode, which can be locat ed at t he bot t om of alm ost every even page of t his m anual. ...
Page 31: Default Settings
1662/1664 Barcode Scanner User Guide DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For t he scanner t o keep t he cust om ized set t ings as user default s, you m ust read t he “ Save as User Default s” barcode. This is a norm al set up barcode, and t he scanner will respond wit h t wo beeps ( low- high t one) .
Page 32: Read A Setup Barcode
Quick Start READ A SETUP BARCODE CONFIGURE PARAMETERS For m ost of t he scanner param et ers, only one read is required t o set t hem t o new values. The scanner will respond wit h t wo beeps ( low- high t one) when each param et er is set successfully.
Page 33 1662/1664 Barcode Scanner User Guide The exam ple below shows how t o save your set t ings as “ User Default ” so t hat you m ay rest ore user default s at a lat er t im e:...
Page 34 Quick Start The exam ple below shows how t o set num eric param et ers: Steps Action Scanner Feedback if Successful Power on t he scanner... The scanner will respond wit h a long beep ( high t one) and it s LED indicat or will becom e solid red and go off.
Page 35 1662/1664 Barcode Scanner User Guide The exam ple below shows how t o set st ring param et ers: Steps Action Scanner Feedback if Successful Power on t he scanner... The scanner will respond wit h a long beep ( high t one) and it s LED indicat or will becom e solid red and go off.
Page 36: List The Current Settings
Quick Start LIST THE CURRENT SETTINGS The current set t ings of all scanner param et ers can be sent t o t he host com put er for user inspect ion. The list ing includes pages as shown below. You can select t he page of int erest by having t he scanner read t he “...
Page 37 1662/1664 Barcode Scanner User Guide List set t ings regarding Edit ing Form at 1 List Page 11 ( 1/ 2) List set t ings regarding Edit ing Form at 1 List Page 12 ( 2/ 2) List set t ings regarding Edit ing Form at 2...
Page 38: Create One-Scan Setup Barcodes
Quick Start CREATE ONE-SCAN SETUP BARCODES The fact is m ost of t he scanner param et ers require only one read for set t ing new values. To facilit at e configuring t he scanner, you m ay creat e One- Scan set up barcodes for use. 1D ONE-SCAN SETUP BARCODE The requirem ent s of a 1D One- Scan set up barcode are: ...
Page 39: Setup Qr Code
1662/1664 Barcode Scanner User Guide SETUP QR CODE Users can also scan a single QR Code com bining wit h a series of serial com m ands t o configure t he scanner. For exam ple, if you want t o change t he suffix charact er t o ‘# ’, you...
Page 40: Understanding The Barcode Scanner
Not e: ( 1) The rechargeable bat t ery for 1662/ 1664 m ay not be fully charged when shipped.
Page 41: Power Level
1662/1664 Barcode Scanner User Guide 1.1.1 POWER LEVEL Scan t he barcode below t o get t he bat t ery capacit y inform at ion wit h each increm ent of 20 in percent age t erm s. Remaining Battery Capacity 1.1.2 HOW TO OPERATE THE SCANNER...
Page 42: Auto Power Off & Power-Saving
Chapter 1 Understanding the Barcode Scanner 1.1.3 AUTO POWER OFF & POWER-SAVING The scanner will st ay act ive at power- on, which m ay be followed by a t ransit ion from full CPU speed t o low CPU speed ( Power- Saving) t o aut o shut down ( Aut o Power Off) . ...
Page 43 1662/1664 Barcode Scanner User Guide After establishing a WPAN connection successfully… Once a WPAN connect ion is est ablished successfully, t he scanner will st ay act ive for a specified period of t im e ( 2 m inut es by default ) for dat a t ransm ission. I t s CPU is running at full speed, and t he LED is flashing blue ( On/ Off rat io 0.02 s: 3 s) .
Page 44 Chapter 1 Understanding the Barcode Scanner Auto Off after 0~254 min. (*10) 1) Read t he barcode above t o specify t he t im e int erval in m inut es before t he scanner aut om at ically t urns off. 2) Read t he “...
Page 45: Memory
1662/1664 Barcode Scanner User Guide 1.2 MEMORY The scanned dat a can be sent t o a host com put er im m ediat ely via t he WPAN connect ion or st ored in flash m em ory when t he scanner is set t o Mem ory m ode.
Page 46: Memory Mode
When t he scanner is in m em ory m ode, it m eans any real- t im e connect ion est ablished wit h t he host is disabled. 1662/ 1664 scanner keeps 4MB flash m em ory for m em ory m ode operat ion, which can st ore over 240,000 scans based on EAN- 13 barcodes.
Page 47 WPAN connect ion wit h t he host , if t here is any. I f 1662/ 1664 has never been connect ed t o t he host cordless, it will not be able t o send dat a unt il it...
Page 48: Free Memory
Chapter 1 Understanding the Barcode Scanner Clear Data Confirm 1.2.3 FREE MEMORY You can scan t he barcode below t o show t he available capacit y of t he flash m em ory in percent age t erm s. Available Memory 1.2.4 RECORD COUNT OF MEMORY You can scan t he barcode below t o show t he dat a record count of t he flash m em ory.
Page 49: Led Indicator
1662/1664 Barcode Scanner User Guide 1.3 LED INDICATOR The t riple- color LED on t op of t he scanner is used t o provide feedback. For exam ple, t he LED becom es solid red and goes off upon powering on or running out of t ransm it buffer.
Page 50: Good Read Led
Chapter 1 Understanding the Barcode Scanner t o t ry and re- connect . Red, - - - - - - Flashing red ( On/ Off rat io 0.2 s: 0.2 s) indicat es t he scanner has flashing failed t o t ransm it dat a st ored in m em ory. Press any key t o st op flashing.
Page 51: Beeper
1662/1664 Barcode Scanner User Guide 1.4 BEEPER The scanner has a buzzer t o provide feedback in various operat ing condit ions. Beeping Meaning One long beep, high t one Power on, wit h red LED on ( 1 second) and off quickly ...
Page 52: Beeper Volume
Chapter 1 Understanding the Barcode Scanner from low t o high  WPAN connect ion resum ed, wit h blue LED flashing 1.4.1 BEEPER VOLUME Mute Minimum Volume Medium Volume *Maximum Volume Update...
Page 53: Good Read Beep
1662/1664 Barcode Scanner User Guide 1.4.2 GOOD READ BEEP Frequency 8 kHz *4 kHz 2 kHz 1 kHz Duration *Shortest Shorter Longer Longest Enter Setup...
Page 54: Low Battery Alarm
Chapter 1 Understanding the Barcode Scanner 1.4.3 LOW BATTERY ALARM By default , t he beeper is enabled t o give a warning when t he bat t ery charge get s low. I n order t o prevent dat a loss, you are advised t o replace t he bat t ery im m ediat ely when you hear t wo short beeps ( high t one) .
Page 55: Vibrator
1662/1664 Barcode Scanner User Guide 1.5 VIBRATOR 1.5.1 GOOD READ VIBRATOR Enable Good Read Vibrator *Disable Good Read Vibrator 1.5.2 GOOD READ VIBRATOR DURATION By default , t he Good Read Vibrat or st ays on for 1 second. Specify a value, ranging from 1 t o 254 in unit s of 100 m illiseconds.
Page 56: Send "Nr" To Host
Chapter 1 Understanding the Barcode Scanner 1.6 SEND “NR” TO HOST The scanner can send a “ NR” st ring t o t he host t o not ify a No Read event . Enable *Disable Update...
Page 57: Scan Modes
1662/1664 Barcode Scanner User Guide 1.7 SCAN MODES Different scan m odes are support ed – select t he scan m ode t hat best suit s t he requirem ent s of a specific applicat ion. Refer t o t he com parison t able below.
Page 58: Laser Mode
Chapter 1 Understanding the Barcode Scanner 1.7.1 LASER MODE The scanner will st art scanning once t he t rigger is held down.  The scanning won't st op unt il ( 1) a barcode is decoded, ( 2) t he pre- set t im eout expires, or ( 3) you release t he t rigger.
Page 59: Aiming Mode (1664 Only)
1662/1664 Barcode Scanner User Guide 1.7.4 AIMING MODE (1664 ONLY) The scanner will aim at a barcode once t he t rigger is pressed, and st art scanning when t he t rigger is pressed again wit hin one second.
Page 60: Continuous Mode (1662 Only)
Chapter 1 Understanding the Barcode Scanner 1.7.6 CONTINUOUS MODE (1662 ONLY) The scanner is always scanning.  Aft er a successful decoding, t he rem oval of barcode is required. I t is not allowed t o proceed t o decode unt il t he decoding delay t im e has passed.
Page 61: Multicode Mode (1664 Only)
1662/1664 Barcode Scanner User Guide 1.7.8 MULTICODE MODE (1664 ONLY) This m ode is designed t o decode m ult iple barcodes at one t im e. The scanning st art s as long as t he t rigger is pressed down, capable of decoding m ult iple barcodes based on t he arranged m ult icode set t ings ( refer t o ScanMast er user guide) .
Page 62: Release Mode
Chapter 1 Understanding the Barcode Scanner Two Times Three Times Scan t he barcode below t o enable t he Sa m e Ba r code Allow a nce funct ion which increases decoding by one t im e aut om at ically. Enable Same Barcode Allowance *Disable Same Barcode Allowance 1.7.9 RELEASE MODE...
Page 63: Scanning Timeout
1662/1664 Barcode Scanner User Guide 1.8 SCANNING TIMEOUT Specify t he scanning t im e int erval ( 1~ 254 sec.; 0= Disable) when t he scan m ode is set t o any of t he following – ...
Page 64: Delay Between Re-Read
Aut o Power Off m ode  Cont inuous m ode ( 1662 only)  Alt ernat e m ode ( 1662 only)  Laser m ode ( 1664 only wit h t he Aut o- sense funct ion working) 100 ms...
Page 65: Read Redundancy For All Symblogies
1662/1664 Barcode Scanner User Guide 1.10 READ REDUNDANCY FOR ALL SYMBLOGIES Select t he level of reading securit y. For exam ple,  I f " No Redundancy" is select ed, one successful decoding will m ake t he reading valid and induce t he "...
Page 66: Addon Security For Upc/Ean Barcodes
Chapter 1 Understanding the Barcode Scanner 1.11 ADDON SECURITY FOR UPC/EAN BARCODES The scanner is capable of decoding a m ix of UPC/ EAN barcodes wit h or wit hout addons. The read redundancy ( 2~ 30 t im es) allows changing t he num ber of t im es t o decode a UPC/ EAN barcode before t ransm ission.
Page 67: Use Direct Usb Cable
User Guide 1.13 USE DIRECT USB CABLE 1662/ 1664 support s Direct USB int erface for charging t he bat t ery and/ or sending dat a t o t he host in m em ory m ode. Refer t o 1.2.2 Mem ory...
Page 68: Picklist Mode (1664 Only)
HI D profile: Press any one of t he following keys “ Scroll Lock” , “ Num ber Bluet oot h Lock” or “ Caps Lock” on t he host com put er t o t rigger t he waking up of 1662/ 1664. ...
Page 69: Time Stamp
1662/1664 Barcode Scanner User Guide 1.16 TIME STAMP Specify t im e st am p form at added t o t he prefix or suffix of a dat a. Up t o t hree set t ings can be configured: ...
Page 70 Chapter 1 Understanding the Barcode Scanner Date Output *Enable Date Output Disable Hour Output *Enable Hour Output Diable Minute Output *Enable Minute Output Disalbe Second Output *Enable Second Output Diable Update...
Page 71: Separator For Date And Time
1662/1664 Barcode Scanner User Guide Decoding Data and Time Year Setup Date Setup Time Setup 1) Read t he barcode above t o apply t im e or dat e code separat ely, and follow st eps 2~ 3. 2) Read t he “...
Page 72: Date Format
Chapter 1 Understanding the Barcode Scanner 1.16.3 DATE FORMAT The dat e form at includes year, m ont h and day. There are t hree kinds of com binat ions can be configured t o specify Year, Mont h and Day: ...
Page 73: Decode Setting (1664 Only)
1662/1664 Barcode Scanner User Guide 1.17 2D DECODE SETTING (1664 ONLY) 1.17.1 AIMING PATTERN Enable/ Disable t he aim ing pat t ern during scanning. *Enable Disable 1.17.2 DECODING ILLUMINATION Enable/ Disable illum inat ion during scanning.  Enabling illum inat ion usually result s in superior im ages. The effect iveness of t he illum inat ion decreases as t he dist ance t o t he t arget increases.
Page 74: Hardware Reset
Chapter 1 Understanding the Barcode Scanner 1.18 HARDWARE RESET 1.18.1 RESTORE SYSTEM DEFAULTS I n addit ion t o scanning t he “ Rest ore Syst em Default s” barcode, t he following procedure using key com binat ions, can be used t o rest ore t he syst em default s during operat ion. 1) Hold down t he [ Power/ Delet e] key.
Page 75: Mobile Phone/Display Mode
1662/1664 Barcode Scanner User Guide 1.19 MOBILE PHONE/DISPLAY MODE By default t his m ode is disabled. There is a big im provem ent in reading barcodes displayed on m obile phones and elect ronic displays when t his m ode is enabled.
Page 76: Selecting Output Interface
Chapter 2 SELECTING OUTPUT INTERFACE I n order t o est ablish a proper connect ion bet ween host com put er and t he scanner, we suggest following t hese inst ruct ions – 1) I nst all bat t ery and hold down t he [ Power/ Delet e] key for 2 seconds t o t urn on t he scanner.
Page 77: Bluet Oot H Hi D
1662/1664 Barcode Scanner User Guide 2.1 BLUETOOTH ® ® For Bluet oot h HI D, refer t o Chapt er 3 – Set t ing up a WPAN Connect ion for relat ed connect ion set t ings. The scanned dat a will be t ransm it t ed t o t he com put er. To capt ure t he dat a run any t ext edit or on your com put er.
Page 78: Activate Bluetooth Hid & Select Keyboard Type
Chapter 2 Selecting Output Interface 2.1.1 ACTIVATE BLUETOOTH ® HID & SELECT KEYBOARD TYPE ® When Bluet oot h HI D int erface is act ivat ed, you will have t o select a keyboard t ype t o ® com plet e t his set t ing.
Page 79: Reset Connection
1662/1664 Barcode Scanner User Guide The following keyboard t ypes are support ed for Apple — Keyboard Type (Apple) Keyboard Type (Apple) Apple ( US) Apple ( Swiss Germ an) Apple ( French) Apple ( Danish) Apple ( Germ an)
Page 80: Keyboard Settings
Chapter 2 Selecting Output Interface 2.1.3 KEYBOARD SETTINGS  Alphabet Layout  Num eric Layout  Capit al Lock Type  Capit al Lock Set t ing  Alphabet Transm ission  Num eric Transm ission  Kanj i Transm ission ...
Page 81 1662/1664 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout , which is norm ally used in west ern count ries.  Select “ Lower Row” for t he “ Num eric Layout ” set t ing because t he upper row is for special charact ers.
Page 82 Chapter 2 Selecting Output Interface Numeric Layout Select a proper layout t hat m at ches t he alphabet layout . The scanner will m ake adj ust m ent s according t o t his set t ing. Options Description Norm al Depends on t he [ Shift ] key or [ Shift Lock] set t ing...
Page 83 1662/1664 Barcode Scanner User Guide Capital Lock Capital Lock State Description Capit al Lock OFF Assum ing t hat t he st at us of Caps Lock on t he keyboard is OFF, t ransm it t ed charact ers are exact ly t he sam e as in t he barcode ( when "...
Page 84 Chapter 2 Selecting Output Interface Alphabet Transmission By default , t he alphabet t ransm ission is case- sensit ive, m eaning t hat t he alphabet will be t ransm it t ed according t o t he original case, t he st at us of Caps Lock on t he k eyboard, as well as t he Capit al Lock set t ing.
Page 85 1662/1664 Barcode Scanner User Guide Numeric Transmission By default , t he alphanum eric keypad is used for t ransm it t ing digit s. Select “ Num eric Keypad” if you wish t o use t he keys on t he num eric keypad.
Page 86: Inter-Character Delay
Chapter 2 Selecting Output Interface ALT Composing By default , Alt ernat e key com posing is disabled. Select [ Yes] t o allow em ulat ing Alt ernat e key code of a specific keyboard charact er. For exam ple, [ Alt ] + [ 065] will be sent t o host for t he charact er “...
Page 87: Inter-Function Delay
1662/1664 Barcode Scanner User Guide 2.1.5 INTER-FUNCTION DELAY By default , t he int er- funct ion delay is set t o zero. Specify a value, ranging from 0 t o 254 in unit s of m illiseconds, t o m at ch t he com put er response t im e of t he keyboard int erface.
Page 88: Hid Character Transmit Mode
Chapter 2 Selecting Output Interface 2.1.6 HID CHARACTER TRANSMIT MODE By default , HI D int erface sends dat a t o t he host charact er by charact er. You m ay have t he scanner read t he “ Bat ch Processing” barcode t o process dat a in bat ch. Batch Processing *By Character Not e: “...
Page 89: Keypad Support For Iphone/Ipad
1662/1664 Barcode Scanner User Guide 2.1.8 KEYPAD SUPPORT FOR IPHONE/IPAD When t he scanner has been successfully connect ed t o iPhone or iPad for dat a collect ion, t he onscreen keypad of iPhone or iPad will disappear. Read t he “ Use POWER Key t o Show or Hide Keypad”...
Page 90: Transmit Speed
Chapter 2 Selecting Output Interface 2.1.10 TRANSMIT SPEED By default , t he BT HI D t ransm it speed is set t o fast t o have t he scanner work in quicker t ransm it speed. Normal *Fast 2.1.11 BT HID SLAVE/MASTER SWITCHING By default , t he BT HI D role is set t o m ast er.
Page 91: Bluet Oot H Spp Slave
1662/1664 Barcode Scanner User Guide 2.2 BLUETOOTH ® SPP SLAVE ® For Bluet oot h SPP Slave, refer t o Chapt er 3 – Set t ing up a WPAN Connect ion for relat ed connect ion set t ings.
Page 92: Ack/Nak Timeout
Chapter 2 Selecting Output Interface 2.2.3 ACK/NAK TIMEOUT By default , t he scanner sends dat a t o t he host wit hout wait ing for an ACK/ NAK response before sending m ore dat a. Specify a value, ranging from 1 t o 99 in unit s of 0.1 second. I f no response wit hin t he specified period of t im e, t he scanner will at t em pt t o send t he sam e dat a t wo m ore t im es.
Page 93: Bluet Oot H ® Spp Mast Er
1662/1664 Barcode Scanner User Guide 2.3 BLUETOOTH ® SPP MASTER As a SPP m ast er device, t he scanner will be able t o resum e connect ion wit h t he host upon powering on again, as long as t he host applicat ion is running. I f t he scanner fails t o resum e connect ion, it will t ry every 5 seconds t o re- connect t o t he host unless you read t he “...
Page 94 Users can also scan a QR Code t hat com bines t he “ Set Connect ion” and “ MAC I D” set up barcodes t o connect wit h t he t arget device. The exam ple below is a 2D barcode cont aining codes ‘# @CipherLab’, ‘88686471166254’...
Page 95: Inter-Function Delay
1662/1664 Barcode Scanner User Guide The concat enat ion of set up barcodes can be com bined t o creat e a single 2D barcode as below: Setup QR Code for connecting with a target device Exit SPP Master Mode To st op such re- connect ion, read “...
Page 96: Ack/Nak Timeout
Chapter 2 Selecting Output Interface 2.3.3 ACK/NAK TIMEOUT By default , t he scanner sends dat a t o t he host wit hout wait ing for an ACK/ NAK response before sending m ore dat a. Specify a value, ranging from 1 t o 99 in unit s of 0.1 second. I f no response wit hin t he specified period of t im e, t he scanner will at t em pt t o send t he sam e dat a t wo m ore t im es.
Page 97: Bt Spp Master Hardware Flow Control
1662/1664 Barcode Scanner User Guide 2.3.5 BT SPP MASTER HARDWARE FLOW CONTROL By default , t he dat a sending via Bluet oot h SPP doesn’t em ploy hardware flow cont rol. I n som e cases users m ay want t o enable hardware flow cont rol t o prevent dat a loss during t ransm ission.
Page 98: Usb Hid Via 3610
Chapter 2 Selecting Output Interface 2.4 USB HID VIA 3610 For USB HI D, connect 3610 t o t he USB port of PC, and t hen connect t he scanner t o 3610. The scanned dat a will be t ransm it t ed t o t he com put er. To capt ure t he dat a run any t ext edit or on your com put er.
Page 99: Activate Usb Hid & Select Keyboard Type
1662/1664 Barcode Scanner User Guide 2.4.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HI D int erface is act ivat ed, you will have t o select a keyboard t ype t o com plet e t his set t ing.
Page 100: Keyboard Settings
Chapter 2 Selecting Output Interface 2.4.2 KEYBOARD SETTINGS  Alphabet Layout  Num eric Layout  Capit al Lock Type  Capit al Lock Set t ing  Alphabet Transm ission  Num eric Transm ission  Kanj i Transm ission Alphabet Layout By default , t he alphabet layout is set t o norm al m ode, also known as t he st andard English layout .
Page 101 1662/1664 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout , which is norm ally used in west ern count ries.  Select “ Lower Row” for t he “ Num eric Layout ” set t ing because t he upper row is for special charact ers.
Page 102 Chapter 2 Selecting Output Interface Numeric Layout Select a proper layout t hat m at ches t he alphabet layout . The scanner will m ake adj ust m ent s according t o t his set t ing. Options Description Norm al Depends on t he [ Shift ] key or [ Shift Lock] set t ing...
Page 103 1662/1664 Barcode Scanner User Guide Capital Lock Capital Lock State Description Capit al Lock OFF Assum ing t hat t he st at us of Caps Lock on t he keyboard is OFF, t ransm it t ed charact ers are exact ly t he sam e as in t he barcode ( when "...
Page 104 Chapter 2 Selecting Output Interface Alphabet Transmission By default , t he alphabet t ransm ission is case- sensit ive, m eaning t hat t he alphabet will be t ransm it t ed according t o t he original case, t he st at us of Caps Lock on t he k eyboard, as well as t he Capit al Lock set t ing.
Page 105 1662/1664 Barcode Scanner User Guide Numeric Transmission By default , t he alphanum eric keypad is used for t ransm it t ing digit s. Select “ Num eric Keypad” if you wish t o use t he keys on t he num eric keypad.
Page 106: Inter-Character Delay
Chapter 2 Selecting Output Interface 2.4.3 INTER-CHARACTER DELAY By default , t he int er- charact er delay is set t o zero. Specify a value, ranging from 0 t o 254 in unit s of m illiseconds, t o m at ch t he com put er response t im e of t he keyboard int erface.
Page 107: Hid Character Transmit Mode
1662/1664 Barcode Scanner User Guide 2.4.5 HID CHARACTER TRANSMIT MODE By default , HI D int erface sends dat a t o t he host charact er by charact er. You m ay have t he scanner read t he “ Bat ch Processing” barcode t o process dat a in bat ch.
Page 108: Usb Virtual Com Via 3610
Chapter 2 Selecting Output Interface 2.5 USB VIRTUAL COM VIA 3610 Connect 3610 t o t he USB port of PC, and t hen connect t he scanner t o 3610. You m ay run HyperTerm inal.exe on t he com put er t o view and capt ure t he dat a t ransm ission from t he scanner.
Page 109: Ack/Nak Timeout
1662/1664 Barcode Scanner User Guide 2.5.4 ACK/NAK TIMEOUT By default , t he scanner sends dat a t o t he host wit hout wait ing for an ACK/ NAK response before sending m ore dat a. Specify a value, ranging from 1 t o 99 in unit s of 0.1 second. I f no response wit hin t he specified period of t im e, t he scanner will at t em pt t o send t he sam e dat a t wo m ore t im es.
Page 110: Usb Vcom Via 3610 Auto-Reconnection
Chapter 2 Selecting Output Interface 2.5.5 USB VCOM VIA 3610 AUTO-RECONNECTION Users can decide whet her t o have t he scanner aut om at ically reconnect t o a paired device aft er disconnect ion, and t he occasion for reconnect ing. *Auto reconnect immediately Auto reconnect on...
Page 111: Direct Usb Hid
1662/ 1664 support s “ Direct ” USB HI D int erface for m em ory m ode. Use t he provided USB cable t o connect 1662/ 1664 t o t he USB port of PC. Run any t ext edit or on a com put er t o view and capt ure t he scanned dat a being t ransm it t ed t o t he com put er.
Page 112: Activate Usb Hid & Select Keyboard Type
Chapter 2 Selecting Output Interface 2.6.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HI D int erface is act ivat ed, please select a keyboard t ype t o com plet e t his set t ing. Activate Direct USB HID &...
Page 113 1662/1664 Barcode Scanner User Guide The following keyboard t ypes are support ed for Apple — Keyboard Type (Apple) Keyboard Type (Apple) Apple ( US) Apple ( Swiss Germ an) Apple ( French) Apple ( Danish) Apple ( Germ an)
Page 114: Keyboard Settings
Chapter 2 Selecting Output Interface 2.6.2 KEYBOARD SETTINGS  Alphabet Layout  Num eric Layout  Capit al Lock Type  Capit al Lock Set t ing  Alphabet Transm ission  Num eric Transm ission  Kanj i Transm ission Alphabet Layout By default , t he alphabet layout is set t o norm al m ode, also known as t he st andard English layout .
Page 115 1662/1664 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout , which is norm ally used in west ern count ries.  Select “ Lower Row” for t he “ Num eric Layout ” set t ing because t he upper row is for special charact ers.
Page 116 Chapter 2 Selecting Output Interface Numeric Layout Select a proper layout t hat m at ches t he alphabet layout . The scanner will m ake adj ust m ent s according t o t his set t ing. Options Description Norm al Depends on t he [ Shift ] key or [ Shift Lock] set t ing...
Page 117 1662/1664 Barcode Scanner User Guide Capital Lock Capital Lock State Description Capit al Lock OFF Assum ing t hat t he st at us of Caps Lock on t he keyboard is OFF, t ransm it t ed charact ers are exact ly t he sam e as in t he barcode ( when "...
Page 118 Chapter 2 Selecting Output Interface Alphabet Transmission By default , t he alphabet t ransm ission is case- sensit ive, m eaning t hat t he alphabet will be t ransm it t ed according t o t he original case, t he st at us of Caps Lock on t he k eyboard, as well as t he Capit al Lock set t ing.
Page 119 1662/1664 Barcode Scanner User Guide Numeric Transmission By default , t he alphanum eric keypad is used for t ransm it t ing num erics. Select “ Num eric Keypad” if want t o use t he keys on t he num eric keypad.
Page 120: Inter-Character Delay
Chapter 2 Selecting Output Interface 2.6.3 INTER-CHARACTER DELAY By default , t he int er- charact er delay is set t o zero. Specify a value, ranging from 0 t o 254 in unit s of m illiseconds, t o m at ch t he com put er response t im e of t he keyboard int erface.
Page 121: Hid Character Transmit Mode
1662/1664 Barcode Scanner User Guide 2.6.5 HID CHARACTER TRANSMIT MODE By default , HI D int erface sends dat a t o t he host charact er by charact er. You m ay have t he scanner read t he “ Bat ch Processing” barcode t o process dat a in bat ch.
Page 122: Direct Usb Virtual Com
2.7 DIRECT USB VIRTUAL COM 1662/ 1664 support s “ Direct ” USB Virt ual COM int erface for m em ory m ode. Use t he provided USB cable t o connect 1662/ 1664 t o t he USB port of PC. You m ay run HyperTerm inal.exe on a com put er t o view and capt ure t he scanned dat a being...
Page 123: Ack/Nak Timeout
1662/1664 Barcode Scanner User Guide 2.7.3 ACK/NAK TIMEOUT By default , t he scanner sends dat a t o t he host wit hout wait ing for an ACK/ NAK response before sending m ore dat a. Specify a value, ranging from 1 t o 99 in unit s of 0.1 second. I f no response wit hin t he specified period of t im e, t he scanner will at t em pt t o send t he sam e dat a t wo m ore t im es.
Page 124 Chapter 2 Selecting Output Interface Update...
Page 125: Set Up A Wpan Connection
Chapter 3 SET UP A WPAN CONNECTION The scanner can be configured t o send dat a t o a host com put er wirelessly via t he 3610 ® dongle, or t o a not ebook com put er or PDA wit h Bluet oot h wireless t echnology.
Page 126: Connecting Via 3610
Users can also scan a QR Code t hat com bines t he “ Set Connect ion” and “ Serial Num ber” set up barcodes t o connect t o 3610. The ex am ple below is a QR Code cont aining codes ‘# @CipherLab’, ‘88686471166254’...
Page 127 1662/1664 Barcode Scanner User Guide is t o m ake t hem m ore readable. # @CipherLab88686471166254BS6065535 Command Purpose # @CipherLab Ent er set up Set connect ion 88686471166254 BS6065535 Serial num ber of 3610 The concat enat ion of set up barcodes can be com bined t o creat e a single 2D barcode as below:...
Page 128: Change Interface
Chapter 3 Set up a WPAN Connection 3.1.2 CHANGE INTERFACE I f you want t o change t he int erface of 3610, use one of t he connect ed scanners t o configure t he int erface- relat ed set t ings and it will pass t he new set t ings t o 3610, which will t hen init ialize and pass t he set t ings t o any ot her connect ed scanners.
Page 129: Configure Related Settings
1662/1664 Barcode Scanner User Guide 3.1.3 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default , t his feat ure is enabled, m eaning t he scanner will list en t o t he wireless net work at a reduced rat e.
Page 130: Configure Related Settings
Chapter 3 Set up a WPAN Connection 3.2.2 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default , t his feat ure is enabled, m eaning t he scanner will list en t o t he wireless net work at a reduced rat e.
Page 131 1662/1664 Barcode Scanner User Guide Change Bluetooth Local Hostname 1) Read t he barcode above t o configure t he device nam e. 2) Read t he “ Hexadecim al Value” barcode on page 272 for t he desired charact er st ring.
Page 132 Chapter 3 Set up a WPAN Connection Authentication When any changes are m ade t o aut hent icat ion and PI N code on t he scanner side, you will have t o rem ove t he scanner from t he paired device list ( called unpairing) and go t hrough t he whole process t o re- est ablish t he connect ion.
Page 133 1662/1664 Barcode Scanner User Guide Use random PIN No PIN required ® Not e: When using Bluet oot h HI D, som e device driver m ay not support pre- defined PI N code for aut hent icat ion. I n t his case, m ake sure you have t he scanner set t o “ No PI N or use random PI N”...
Page 134: Connect To Dongle
Chapter 3 Set up a WPAN Connection 3.2.3 CONNECT TO DONGLE The procedure goes t hrough associat ing devices for est ablishing a WPAN connect ion, which is pret t y m uch t he sam e except for t he soft ware you are using. I f your com put er is ®...
Page 135 1662/1664 Barcode Scanner User Guide ® ® Turn on t he scanner wit h correct WPAN set t ings, such as select Bluet oot h SPP or Bluet oot h HI D, broadcast ing enabled, aut hent icat ion enabled, and PI N code specified, et c. Select t he check box of [ My device is set up and ready t o be found] on your com put er.
Page 136 Chapter 3 Set up a WPAN Connection Click [ Next ] . Ent er t he passkey for aut hent icat ion, which m ust be exact ly t he sam e as configured for t he scanner. Update...
Page 137 1662/1664 Barcode Scanner User Guide Click [ Next ] . Wait for a few seconds for Windows t o exchange passkeys. Enter Setup...
Page 138 Chapter 3 Set up a WPAN Connection Not e: When Bluet oot h securit y is enabled wit hout providing a pre- set PI N code, dynam ic input of PI N code is support ed. Click [ Finish] . ®...
Page 139 1662/1664 Barcode Scanner User Guide Now t he t arget scanner will be list ed as shown below. You can have up t o seven scanners connect ed t o one com put er at t he sam e t im e.
Page 140 Chapter 3 Set up a WPAN Connection ® Bluetooth SPP Connected ® Bluetooth SPP Disconnected Update...
Page 141: Secure Simple Pairing (Ssp)
1662/1664 Barcode Scanner User Guide 3.2.4 SECURE SIMPLE PAIRING (SSP) ® Secure Sim ple Pairing ( SSP) , int roduced in Bluet oot h Core Specificat ion 2.1 + EDR, is a new feat ure designed t o ease t he pairing process while keeping up t he com m unicat ion ®...
Page 142: An Ge Sym Bology Setti N Gs
Chapter 4 CHANGE SYMBOLOGY SETTINGS I n t his chapt er, a brief on t he sym bology set t ings is provided for your reference. For users’ convenience, t he t wo set t ing barcodes below allows disabling/ enabling support ed sym bologies all at once.
Page 143: Codabar
1662/1664 Barcode Scanner User Guide 4.1 CODABAR *Enable Disable 4.1.1 START/STOP TRANSMISSION Decide whet her t o include t he st art / st op charact ers in t he dat a being t ransm it t ed. Transmit Start/Stop...
Page 144: Code Length Qualification
Chapter 4 Change Symbology Settings 4.1.3 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h. ...
Page 145: Code 25 - I Ndust Rial 25
1662/1664 Barcode Scanner User Guide 4.2 CODE 25 – INDUSTRIAL 25 *Enable Disable Enter Setup...
Page 146: Code Length Qualification
Chapter 4 Change Symbology Settings 4.2.1 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h. ...
Page 147: Code 25 - I Nt Erleaved 25
1662/1664 Barcode Scanner User Guide 4.3 CODE 25 – INTERLEAVED 25 *Enable Disable 4.3.1 VERIFY CHECK DIGIT Decide whet her t o verify t he check digit . When desired, select one of t he algorit hm s, USS or OPCC. I f incorrect , t he barcode will not be accept ed.
Page 148: Convert To Ean-13
Chapter 4 Change Symbology Settings 4.3.3 CONVERT TO EAN-13 Decide whet her t o convert a 14- charact er barcode int o EAN- 13 if t he following requirem ent s are m et :  The barcode m ust have a leading 0 and a valid EAN- 13 check digit . ...
Page 149: Code Length Qualification
1662/1664 Barcode Scanner User Guide 4.3.4 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h.
Page 150: Code 25 - Mat Rix 25
Chapter 4 Change Symbology Settings 4.4 CODE 25 – MATRIX 25 Enable *Disable 4.4.1 VERIFY CHECK DIGIT Decide whet her t o verify t he check digit . I f incorrect , t he barcode will not be accept ed. Verify Matrix 25 Check Digit *Do Not Verify...
Page 151: Code Length Qualification
1662/1664 Barcode Scanner User Guide 4.4.3 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h.
Page 152: Code 25 - Chinese 25
Chapter 4 Change Symbology Settings 4.5 CODE 25 – CHINESE 25 Enable *Disable Update...
Page 153: Italian Pharmacode (Code 32)
1662/1664 Barcode Scanner User Guide 4.6 ITALIAN PHARMACODE (CODE 32) Enable *Disable Not e: Code 39 m ust be enabled first . Enter Setup...
Page 154: Code 39
Chapter 4 Change Symbology Settings 4.7 CODE 39 *Enable Disable 4.7.1 VERIFY CHECK DIGIT Decide whet her t o verify t he check digit . I f incorrect , t he barcode will not be accept ed. Verify Code 39 Check Digit *Do Not Verify 4.7.2 TRANSMIT CHECK DIGIT...
Page 155: St Andard/ Full Asci I Code 39
1662/1664 Barcode Scanner User Guide 4.7.3 STANDARD/FULL ASCII CODE 39 Decide whet her t o support Code 39 Full ASCI I t hat includes all t he alphanum eric and special charact ers. Code 39 Full ASCII *Standard Code 39 Not e: Triopt ic Code 39 and Code 39 Full ASCI I cannot be enabled at t he sam e t im e.
Page 156: Code Length Qualification
Chapter 4 Change Symbology Settings 4.7.4 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h. ...
Page 157: Triopt Ic Code 39
1662/1664 Barcode Scanner User Guide 4.8 TRIOPTIC CODE 39 Decide whet her t o decode Triopt ic Code 39.  Triopt ic Code 39 is a variant of Code 39 used in t he m arking of com put er t ape cart ridges.
Page 158: Code 93
Chapter 4 Change Symbology Settings 4.9 CODE 93 *Enable Disable Update...
Page 159: Code Length Qualification
1662/1664 Barcode Scanner User Guide 4.9.1 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h.
Page 160: Code 128
Chapter 4 Change Symbology Settings 4.10 CODE 128 *Enable Disable Update...
Page 161: Gs1-128 (Ean-128)
1662/1664 Barcode Scanner User Guide 4.11 GS1-128 (EAN-128) *Enable Disable Not e: GS1- 128 barcodes can be decoded only when t his set t ing is enabled. 4.11.1 TRANSMIT CODE ID Decide whet her t o include t he Code I D ( “...
Page 162: Gs1 Formatting
Chapter 4 Change Symbology Settings 4.11.3 GS1 FORMATTING Decide whet her t o enable GS1 form at t ing for GS1- 128. When enabled, code I D t ransm it t ing will be disabled; however, t he field separat or and applicat ion I D m ark charact ers will be aut om at ically added t o t he out put dat a.
Page 163: I Sbt 128
1662/1664 Barcode Scanner User Guide 4.12 ISBT 128 *Enable Disable 4.12.1 ISBT CONCATENATION (1664 ONLY) Decide whet her t o decode and concat enat e pairs of I SBT barcodes.  Disable I SBT Concat enat ion I t will not concat enat e pairs of I SBT barcodes it encount ers. Only one single I SBT 128 barcode out put s.
Page 164: Isbt Concatenation Redundancy (1664 Only)
Chapter 4 Change Symbology Settings 4.12.2 ISBT CONCATENATION REDUNDANCY (1664 ONLY) Specify t he concat enat ion redundancy ( 2~ 20 t im es) when I SBT concat enat ion is enabled. ISBT Concatenation Redundancy 2~20 (*10) 1) Read t he barcode above t o specify t he concat enat ion redundancy. 2) Read t he “...
Page 165: Gs1 Databar (Rss Family)
1662/1664 Barcode Scanner User Guide 4.13 GS1 DATABAR (RSS FAMILY) I t is cat egorized int o t hree groups: Group I — GS1 DataBar Omnidirectional (RSS-14)  GS1 Dat aBar Om nidirect ional This group consist s of t he following: ...
Page 166: Gs1 Databar Omnidirectional (Rss-14)
Chapter 4 Change Symbology Settings 4.13.2 GS1 DATABAR OMNIDIRECTIONAL (RSS-14) *Enable RSS-14 & RSS Expanded (Groups I, II) Disable When GS1 form at t ing for GS1 Dat aBar Om nidirect ional is enabled, code I D t ransm it t ing will be disabled;...
Page 167: Gs1 Databar Expanded (Rss Expanded)
1662/1664 Barcode Scanner User Guide Enable *Disable 4.13.3 GS1 DATABAR EXPANDED (RSS EXPANDED) *Enable RSS-14 & RSS Expanded (Groups I, II) Disable When GS1 form at t ing for GS1 Dat aBar Expanded is enabled, code I D t ransm it t ing will be disabled.
Page 168: Gs1 Databar Limited (Rss Limited)
Chapter 4 Change Symbology Settings *Disable 4.13.4 GS1 DATABAR LIMITED (RSS LIMITED) *Enable RSS Limited (Group III) Disable When GS1 form at t ing for GS1 Dat aBar Lim it ed is enabled, code I D t ransm it t ing will be disabled;...
Page 169: Convert To Upc/Ean
1662/1664 Barcode Scanner User Guide *Disable 4.13.5 CONVERT TO UPC/EAN This only applies t o GS1 Dat aBar Om nidirect ional and GS1 Dat aBar Lim it ed barcodes not decoded as part of a Com posit e barcode. ...
Page 170: Application Id Mark
Chapter 4 Change Symbology Settings 4.13.7 APPLICATION ID MARK You m ay want t o add an applicat ion I D m ark ( 1 charact er long) t o t he left ( AI Mark1) or right ( AI Mark2) of an applicat ion I D ( AI ) for t he purpose of labeling it when form at t ing t he GS1 dat a.
Page 171: Msi
1662/1664 Barcode Scanner User Guide 4.14 MSI Enable *Disable 4.14.1 VERIFY CHECK DIGIT Select one of t he t hree calculat ions t o verify check digit ( s) when decoding barcodes. I f incorrect , t he barcode will not be accept ed.
Page 172: Code Length Qualification
Chapter 4 Change Symbology Settings 4.14.3 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h. ...
Page 173: 154
1662/1664 Barcode Scanner User Guide 4.15 EAN-8 EAN-8 *Enable EAN-8 (No Addon) Disable EAN-8 Addon 2 Enable EAN-8 Addon 2 *Disable EAN-8 Addon 5 Enable EAN-8 Addon 5 *Disable 4.15.1 TRANSMIT CHECK DIGIT Decide whet her t o include t he check digit in t he dat a being t ransm it t ed.
Page 174: 155
Chapter 4 Change Symbology Settings 4.16 EAN-13 EAN-13 *Enable EAN-13 (No Addon) Disable Decide whet her t o read EAN- 13 barcodes ending wit h Addon 2. EAN-13 Addon 2 Enable EAN-13 Addon 2 *Disable Decide whet her t o read EAN- 13 barcodes ending wit h Addon 5. EAN-13 Addon 5 Enable EAN-13 Addon 5 *Disable...
Page 175: Addon Modes
1662/1664 Barcode Scanner User Guide 4.16.1 EAN-13 ADDON MODES Decide whet her t o enable EAN- 13 414/ 419/ 434/ 439 Addon Mode. When enabled, barcodes st art ing wit h 414/ 419/ 434/ 439 won’t be decoded if t he scanned barcodes do not have t he Addon 2 or Addon 5 suffix.
Page 176 Chapter 4 Change Symbology Settings Decide whet her t o enable EAN- 13 978 Addon Mode. When enabled, barcodes st art ing wit h 978 won’t be decoded if t he scanned barcodes do not have t he Addon 2 or Addon 5 suffix.
Page 177 1662/1664 Barcode Scanner User Guide Decide whet her t o enable EAN- 13 529 Addon Mode. When enabled, barcodes st art ing wit h 529 won’t be decoded if t he scanned barcodes do not have t he Addon 2 or Addon 5 suffix.
Page 178: Convert To Isbn
Chapter 4 Change Symbology Settings 4.16.2 CONVERT TO ISBN Decide whet her t o convert t he EAN- 13 barcode, st art ing wit h 978, t o I SBN. Convert EAN-13 to ISBN *Do Not Convert 4.16.3 CONVERT TO ISSN (1664 ONLY) Decide whet her t o convert t he EAN- 13 barcode, st art ing wit h 977 t o I SSN.
Page 179: Ucc Coupon Extended Code
1662/1664 Barcode Scanner User Guide 4.17 UCC COUPON EXTENDED CODE Decide whet her t o decode t he following barcodes as Coupon Code.  UPC- A barcodes st art ing wit h digit “ 5”  EAN- 13 barcodes st art ing wit h digit s “ 99”...
Page 180: Upc-A
Chapter 4 Change Symbology Settings 4.18 UPC-A UPC-A *Enable UPC-A (No Addon) Disable UPC-A Addon 2 Enable UPC-A Addon 2 *Disable UPC-A Addon 5 Enable UPC-A Addon 5 *Disable Update...
Page 181: Convert To Ean-13
1662/1664 Barcode Scanner User Guide 4.18.1 CONVERT TO EAN-13 Decide whet her t o expand t he read UPC- A barcode, as well as it s addons, int o EAN- 13.  Aft er conversion, t he dat a follow s EAN- 13 form at and is affect ed by EAN- 13 program m ing select ions ( e.g.
Page 182: Upc-E
Chapter 4 Change Symbology Settings 4.19 UPC-E UPC-E *Enable UPC-E (No Addon) Disable UPC-E Addon 2 Enable UPC-E Addon 2 *Disable UPC-E Addon 5 Enable UPC-E Addon 5 *Disable Update...
Page 183: Select System Number
1662/1664 Barcode Scanner User Guide 4.19.1 SELECT SYSTEM NUMBER Decide whet her t o decode t he ordinary UPC- E barcodes only or bot h UPC- E0 and UPC- E1 barcodes.  Syst em num ber enabled for decoding UPC- E0 barcodes.
Page 184: Transmit System Number
Chapter 4 Change Symbology Settings 4.19.3 TRANSMIT SYSTEM NUMBER Decide whet her t o include t he syst em num ber in t he dat a being t ransm it t ed. Transmit UPC-E System Number *Do Not Transmit 4.19.4 TRANSMIT CHECK DIGIT Decide whet her t o include t he check digit in t he dat a being t ransm it t ed.
Page 185: Code 11
1662/1664 Barcode Scanner User Guide 4.20 CODE 11 Enable *Disable 4.20.1 VERIFY CHECK DIGIT Decide whet her t o verify t he check digit ( s) . I f incorrect , t he barcode will not be accept ed. Verify One...
Page 186: Code Length Qualification
Chapter 4 Change Symbology Settings 4.20.3 CODE LENGTH QUALIFICATION To prevent t he " short scan" error, define t he " Lengt h Qualificat ion" set t ings t o ensure t hat t he correct barcode is read by qualifying t he allowable code lengt h. ...
Page 187: Composite Code
1662/1664 Barcode Scanner User Guide 4.21 COMPOSITE CODE 4.21.1 COMPOSITE CC-A/B Decide whet her t o enable Com posit e CC- A/ B. Enable Composite CC-A/B *Disable Decide whet her t o enable GS1 form at t ing for Com posit e CC- A/ B. When enabled, t he field separat or and applicat ion I D m ark will be aut om at ically added t o t he out put dat a.
Page 188: Composite Tlc-39
Chapter 4 Change Symbology Settings 4.21.3 COMPOSITE TLC-39 Enable Composite TLC-39 *Disable 4.21.4 UPC COMPOSITE MODE UPC barcodes can be “ linked” wit h a 2D barcode during t ransm ission as if t hey were one barcode.  UPC Never Linked Transm it UPC barcodes regardless of whet her a 2D barcode is det ect ed.
Page 189: Gs1-128 Emulation Mode For Ucc/Ean Composite Codes
1662/1664 Barcode Scanner User Guide 4.21.5 GS1-128 EMULATION MODE FOR UCC/EAN COMPOSITE CODES Decide whet her t o t ransm it UCC/ EAN Com posit e Code dat a as if it was encoded in GS1- 128 barcodes. Enable GS1-128...
Page 190: Application Id Mark
Chapter 4 Change Symbology Settings 4.21.7 APPLICATION ID MARK You m ay want t o add an applicat ion I D m ark ( 1 charact er long) t o t he left ( AI Mark1) or right ( AI Mark2) of an applicat ion I D ( AI ) for t he purpose of labeling it when form at t ing t he GS1 dat a.
Page 191: Postal Code
1662/1664 Barcode Scanner User Guide 4.22 US POSTAL CODE 4.22.1 US POSTNET *Enable US Postnet Disable 4.22.2 US PLANET *Enable US Planet Disable 4.22.3 TRANSMIT CHECK DIGIT Decide whet her t o include t he check digit in t he dat a being t ransm it t ed.
Page 192: Postal Code
Chapter 4 Change Symbology Settings 4.23 UK POSTAL CODE 4.23.1 UK POSTAL *Enable UK Postal Disable 4.23.2 TRANSMIT CHECK DIGIT Decide whet her t o include t he check digit in t he dat a being t ransm it t ed. *Transmit UK Postal Check Digit Do Not Transmit...
Page 193: More Postal Code
1662/1664 Barcode Scanner User Guide 4.24 MORE POSTAL CODE 4.24.1 JAPAN POSTAL *Enable Japan Postal Disable 4.24.2 AUSTRALIAN POSTAL *Enable Australian Postal Disable 4.24.3 DUTCH POSTAL *Enable Dutch Postal Disable 4.24.4 USPS 4CB/ONE CODE/INTELLIGENT MAIL Enable USPS 4CB/ One Code/...
Page 194: Upu Fics Postal
Chapter 4 Change Symbology Settings 4.24.5 UPU FICS POSTAL Enable UPU FICS Postal *Disable Update...
Page 195: Symbologies
1662/1664 Barcode Scanner User Guide 4.25 2D SYMBOLOGIES 4.25.1 PDF417 *Enable PDF417 Disable 4.25.2 MicroPDF417 Enable MicroPDF417 *Disable Enter Setup...
Page 196: Data Matrix
Chapter 4 Change Symbology Settings 4.25.3 DATA MATRIX *Enable Data Matrix Disable Data Matrix Mirror Decide whet her t o decode m irror im age Dat a Mat rix barcodes.  Never — do not decode Dat a Mat rix barcodes t hat are m irror im ages. ...
Page 197: Maxicode
1662/1664 Barcode Scanner User Guide 4.25.4 MAXICODE *Enable Maxicode Disable 4.25.5 QR CODE *Enable QR Code Disable 4.25.6 MicroQR *Enable MicroQR Disable 4.25.7 AZTEC *Enable Aztec Disable Enter Setup...
Page 198: Macro Pdf
Chapter 4 Change Symbology Settings 4.26 MACRO PDF Macro PDF is a special feat ure for concat enat ing m ult iple PDF barcodes int o one file, known as Macro PDF417 or Macro MicroPDF417. Not e: When print ing barcodes, keep each Macro PDF sequence separat e, as each has a unique ident ifier.
Page 199: Escape Characters
1662/1664 Barcode Scanner User Guide 4.26.2 ESCAPE CHARACTERS When enabled, it uses t he backslash " \ " as an Escape charact er for syst em s t hat can process t ransm issions cont aining special dat a sequences. I t will form at special dat a according t o t he Global Label I dent ifier ( GLI ) prot ocol, which only affect s t he dat a port ion of a Macro PDF sym bol t ransm ission.
Page 200: Defining Output Format
Chapter 5 DEFINING OUTPUT FORMAT You m ay configure t he form at of t he collect ed dat a out put t o t he host com put er. Barcodes read by t he scanner will be processed in t he following sequence – 1) Perform charact er subst it ut ion on t he dat a scanned.
Page 201: Character Substitution
1662/1664 Barcode Scanner User Guide 5.2 CHARACTER SUBSTITUTION Charact er subst it ut ion is perform ed on every occurrence of t he first charact er specified. I f only one charact er is specified, every occurrence of t hat charact er in t he barcode will be t aken away.
Page 202: Single Character Substituion
Chapter 5 Defining Output Format 5.2.1 SINGLE CHARACTER SUBSTITUION Configure Set 1 Configure Set 2 Configure Set 3 1) Read t he barcode above t o enable charact er subst it ut ion by set . For exam ple, read t he “ Set 1” barcode t o configure t he first set of charact er subst it ut ion.
Page 203: Multiple Character Substitution
1662/1664 Barcode Scanner User Guide 5.2.2 MULTIPLE CHARACTER SUBSTITUTION Users can replace a st ring up t o 16 charact ers wit h anot her one. Configure Set 1 Set 1 Set 1 Target String Replacement String Configure Set 2...
Page 204 Chapter 5 Defining Output Format KEY TYPE = NORMAL Replace t he charact er “ 0- 0” wit h “ * * * ” : Read t he Tar get St ring barcode. Read “ 3” , “ 0” , “ 2” , “ D” , “ 3” , and “ 0” barcodes t o specify t he t arget st ring “ 0- 0” ( zero, dash, zero) .
Page 205: Symbologies For Character Substitution (All 3 Sets)
1662/1664 Barcode Scanner User Guide 5.2.3 SYMBOLOGIES FOR CHARACTER SUBSTITUTION (ALL 3 SETS) By default charact er subst it ut ion will be perform ed on all sym bologies. I f t he charact er subst it ut ion is not desired wit h one or m ore sym bologies, read t he “ Do Not Apply”...
Page 206 Chapter 5 Defining Output Format Character Substitution for Code 128 *Apply Do Not Apply Character Substitution for GS1-128 *Apply Do Not Apply Character Substitution for ISBT 128 *Apply Do Not Apply Character Substitution for EAN-8 (No Addon) *Apply Do Not Apply Character Substitution for EAN-8 Addon 2 *Apply Update...
Page 207 1662/1664 Barcode Scanner User Guide Do Not Apply Character Substitution for EAN-8 Addon 5 *Apply Do Not Apply Character Substitution for EAN-13 (No Addon) *Apply Do Not Apply Character Substitution for EAN-13 Addon 2 *Apply Do Not Apply Character Substitution for EAN-13 Addon 5...
Page 208 Chapter 5 Defining Output Format Do Not Apply Character Substitution for Industrial 25 *Apply Do Not Apply Character Substitution for Interleaved 25 *Apply Do Not Apply Character Substitution for Matrix 25 *Apply Do Not Apply Character Substitution for Chinese 25 *Apply Do Not Apply Character Substitution for MSI...
Page 209 1662/1664 Barcode Scanner User Guide Do Not Apply Character Substitution for GS1 DataBar *Apply Do Not Apply Character Substitution for UPC-A (No Addon) *Apply Do Not Apply Character Substitution for UPC-A Addon 2 *Apply Do Not Apply Character Substitution for UPC-A Addon 5...
Page 210 Chapter 5 Defining Output Format Do Not Apply Character Substitution for UPC-E Addon 2 *Apply Do Not Apply Character Substitution for UPC-E Addon 5 *Apply Do Not Apply Character Substitution for UCC Coupon Extended Code *Apply Do Not Apply Character Substitution for Code 11 *Apply Do Not Apply Character Substitution for Composite CC-A/B...
Page 211 1662/1664 Barcode Scanner User Guide Do Not Apply Character Substitution for Composite CC-C *Apply Do Not Apply Character Substitution for Composite TLC-39 *Apply Do Not Apply Character Substitution for US Postnet *Apply Do Not Apply Character Substitution for US Planet...
Page 212 Chapter 5 Defining Output Format Do Not Apply Character Substitution for Japan Postal *Apply Do Not Apply Character Substitution for Australian Postal *Apply Do Not Apply Character Substitution for Dutch Postal *Apply Do Not Apply Character Substitution for USPS 4CB/One Code/Intelligent Mail *Apply Do Not Apply Character Substitution for UPU FICS Postal...
Page 213 1662/1664 Barcode Scanner User Guide Do Not Apply Character Substitution for PDF417 *Apply Do Not Apply Character Substitution for MicroPDF417 *Apply Do Not Apply Character Substitution for Data Matrix *Apply Do Not Apply Character Substitution for Maxicode *Apply Do Not Apply...
Page 214 Chapter 5 Defining Output Format Do Not Apply Character Substitution for MicroQR *Apply Do Not Apply Character Substitution for Aztec *Apply Do Not Apply Update...
Page 215: Prefix/Suffix Code
1662/1664 Barcode Scanner User Guide 5.3 PREFIX/SUFFIX CODE By default , t here is no prefix code, and [ ENTER] or [ CR] ( Carriage Ret urn) is configured t o be suffix code. Up t o 8 charact ers can be configured, for exam ple, “ Barcode_” , and...
Page 216: Code Id
Chapter 5 Defining Output Format 5.4 CODE ID Up t o t wo charact ers for Code I D can be configured for each sym bology. To m ake t he Code I D configurat ion easier, t he scanner provides five pre- defined Code I D set s t hat you can select one and m ake necessary changes on it .
Page 217 1662/1664 Barcode Scanner User Guide Code ID options Set 1 Set 2 Set 3 Set 4 Set 5 Code 39 Triopt ic Code 39 I t alian Pharm acode I ndust rial 25 I nt erleaved 25 Mat rix 25...
Page 218 Chapter 5 Defining Output Format MicroQR Azt ec I ATA Macro PDF417 Macro MicroPDF417 Update...
Page 219: Change Code Id
1662/1664 Barcode Scanner User Guide 5.4.2 CHANGE CODE ID 1) Read t he barcode below t o change code I D of a specific sym bology. 2) Read t he “ Hexadecim al Value” barcode on page 272 for t he desired charact er st ring.
Page 220 Chapter 5 Defining Output Format Configure Code ID for Interleaved 25 Configure Code ID for Matrix 25 Configure Code ID for Chinese 25 Configure Code ID for Configure Code ID for UPC-A Configure Code ID for UPC-E Configure Code ID for UCC Coupon Code Configure Code ID for Code 11...
Page 221 1662/1664 Barcode Scanner User Guide Configure Code ID for US Planet Configure Code ID for UK Postal Configure Code ID for Japan Postal Configure Code ID for Australian Postal Configure Code ID for Dutch Postal Configure Code ID for USPS 4CB / One Code /...
Page 222: Clear Code Id Settings
Chapter 5 Defining Output Format Configure Code ID for MicroQR Configure Code ID for Aztec Configure Code ID for IATA Configure Code ID for Macro PDF417 Configure Code ID for Macro MicroPDF417 5.4.3 CLEAR CODE ID SETTINGS Clear All Code ID Settings Update...
Page 223: Length Code
1662/1664 Barcode Scanner User Guide 5.5 LENGTH CODE A 4- digit code represent ing t he lengt h of barcode dat a ( charact er count ) can be insert ed in front of dat a being t ransm it t ed. Such " Lengt h" code can be individually enabled or disabled for each sym bology.
Page 224 Chapter 5 Defining Output Format Length Code for Code 128 Apply *Do Not Apply Length Code for GS1-128 & GS1 DataBar Apply *Do Not Apply Length Code for ISBT 128 Apply *Do Not Apply Length Code for EAN-8 Apply *Do Not Apply Length Code for EAN-13 Apply *Do Not Apply...
Page 225 1662/1664 Barcode Scanner User Guide Length Code for Italian Pharmacode Apply *Do Not Apply Length Code for Industrial 25 Apply *Do Not Apply Length Code for Interleaved 25 Apply *Do Not Apply Length Code for Matrix 25 Apply *Do Not Apply...
Page 226 Chapter 5 Defining Output Format Length Code for MSI Apply *Do Not Apply Length Code for UPC-A Apply *Do Not Apply Length Code for UPC-E Apply *Do Not Apply Length Code for UCC Coupon Extended Code Apply *Do Not Apply Length Code for Code 11 Apply *Do Not Apply...
Page 227 1662/1664 Barcode Scanner User Guide Length Code for Composite CC-A/B Apply *Do Not Apply Length Code for Composite CC-C Apply *Do Not Apply Length Code for Composite TLC-39 Apply *Do Not Apply Length Code for US Postnet Apply *Do Not Apply...
Page 228 Chapter 5 Defining Output Format Length Code for UK Postal Apply *Do Not Apply Length Code for Japan Postal Apply *Do Not Apply Length Code for Australian Postal Apply *Do Not Apply Length Code for Dutch Postal Apply *Do Not Apply Length Code for USPS 4CB/One Code/Intelligent Mail Apply *Do Not Apply...
Page 229 1662/1664 Barcode Scanner User Guide Length Code for UPU FICS Postal Apply *Do Not Apply Length Code for PDF417 Apply *Do Not Apply Length Code for MicroPDF417 Apply *Do Not Apply Length Code for Data Matrix Apply *Do Not Apply...
Page 230 Chapter 5 Defining Output Format Length Code for QR Code Apply *Do Not Apply Length Code for MicroQR Apply *Do Not Apply Length Code for Aztec Apply *Do Not Apply Update...
Page 231: Multi-Barcode Editor
1662/1664 Barcode Scanner User Guide 5.6 MULTI-BARCODE EDITOR The Mult i- Barcode Edit or allows deciding t he out put sequence of a concat enat ion of barcodes. Up t o five barcodes can be specified. Enabling t his funct ion will force t he scanner t o apply Laser m ode as t he scan m ode.
Page 232: Edit A Concatenation Of Barcodes
Chapter 5 Defining Output Format 5.6.1 EDIT A CONCATENATION OF BARCODES Edit Output Sequence 1) Read t he barcode above t o st art edit ing a concat enat ion of barcodes. 2) Code Type set t ing – read t he “ Hexadecim al Value”...
Page 233 1662/1664 Barcode Scanner User Guide 79 ( y) Chinese 25 5A ( Z) N/ A 7A ( z) Azt ec 5B ( [ ) GS1 Dat aBar ( RSS) 7B ( { ) Micro QR 7C ( | ) USPS 4CB / One Code /...
Page 234: Activate The Concatenation Of Barcodes
Chapter 5 Defining Output Format 5.6.2 ACTIVATE THE CONCATENATION OF BARCODES By default , t he out put sequence edit ing of t he concat enat ion of barcodes is not applied. When “ Enforce Out put Sequence” is enabled, all barcodes read by t he scanner m ust m eet wit h t he crit eria for t he concat enat ion.
Page 235: Removal Of Special Character
1662/1664 Barcode Scanner User Guide 5.7 REMOVAL OF SPECIAL CHARACTER You can only specify 1 charact er, but it will rem ove every m at ching charact er encount ered from t he st art ing posit ion of barcode dat a unt il a different charact er is m et .
Page 236: Applyi N G Form Ats For D Ata Ed I Ti N G
For 1662/ 1664 t o apply any edit ing form at , t he m axim um out put dat a lengt h of a barcode is 7 KB aft er configurat ion. When t he dat a lengt h exceeds 7 KB, edit ing form at will not t ake effect .
Page 237: Activating Editing Formats
1662/1664 Barcode Scanner User Guide 6.1 ACTIVATING EDITING FORMATS 6.1.1 ACTIVATE EDITING FORMATS I f you have already configured any edit ing form at before, you m ay direct ly apply t he edit ing form at . I f not , you m ust st art wit h configuring an edit ing form at first , and t hen, act ivat e t he edit ing form at when it is desired in use.
Page 238: Exclusive Data Editing
Chapter 6 Applying Formats for Data Editing Editing Format 5 Enable *Disable 6.1.2 EXCLUSIVE DATA EDITING By default , only barcodes found m eet ing wit h t he crit eria are processed by t he edit ing form at s. Those found not m eet ing wit h t he crit eria are processed norm ally. When “...
Page 239: How To Configure Editing Formats
1662/1664 Barcode Scanner User Guide 6.2 HOW TO CONFIGURE EDITING FORMATS End Programming Format...
Page 240: Select Format To Configure
Chapter 6 Applying Formats for Data Editing 6.2.1 SELECT FORMAT TO CONFIGURE Start Programming Format Select one edit ing form at ( Form at 1~ 5) and t he param et ers pert aining t o t he edit ing form at can t hen be configured –...
Page 241: Restore Default Format
1662/1664 Barcode Scanner User Guide 6.2.2 RESTORE DEFAULT FORMAT You m ay select an exist ing edit ing form at and have t he default s rest ored. The default set t ings of an edit ing form at are list ed below.
Page 242: Configure Format - Define Data Criteria
Chapter 6 Applying Formats for Data Editing 6.3 CONFIGURE FORMAT — DEFINE DATA CRITERIA Three applicable condit ions can be configured t o check whet her t he dat a read by t he scanner can be processed by t he part icular edit ing form at . Not e: Dat a edit ing cannot be perform ed unless t he t hree condit ions are all m et .
Page 243 1662/1664 Barcode Scanner User Guide Editing Format for Codabar *Apply Do Not Apply Editing Format for Code 39 *Apply Do Not Apply Editing Format for Trioptic Code 39 *Apply Do Not Apply Editing Format for Code 93 *Apply Do Not Apply...
Page 244 Chapter 6 Applying Formats for Data Editing Editing Format for GS1-128 & GS1 DataBar *Apply Do Not Apply Editing Format for ISBT 128 *Apply Do Not Apply Editing Format for EAN-8 *Apply Do Not Apply Editing Format for EAN-8 Addon 2 *Apply Do Not Apply Editing Format for EAN-8 Addon 5...
Page 245 1662/1664 Barcode Scanner User Guide Editing Format for EAN-13 *Apply Do Not Apply Editing Format for EAN-13 Addon 2 *Apply Do Not Apply Editing Format for EAN-13 Addon 5 *Apply Do Not Apply Editing Format for Italian Pharmacode *Apply Do Not Apply...
Page 246 Chapter 6 Applying Formats for Data Editing Editing Format for Interleaved 25 *Apply Do Not Apply Editing Format for Matrix 25 *Apply Do Not Apply Editing Format for Chinese 25 *Apply Do Not Apply Editing Format for MSI *Apply Do Not Apply Editing Format for UPC-A *Apply Do Not Apply...
Page 247 1662/1664 Barcode Scanner User Guide Editing Format for UPC-A Addon 2 *Apply Do Not Apply Editing Format for UPC-A Addon 5 *Apply Do Not Apply Editing Format for UPC-E *Apply Do Not Apply Editing Format for UPC-E Addon 2 *Apply...
Page 248 Chapter 6 Applying Formats for Data Editing Editing Format for UCC Coupon Extended Code *Apply Do Not Apply Editing Format for Code 11 *Apply Do Not Apply Editing Format for Composite CC-A/B *Apply Do Not Apply Editing Format for Composite CC-C *Apply Do Not Apply Editing Format for Composite TLC-39...
Page 249 1662/1664 Barcode Scanner User Guide Editing Format for US Postnet *Apply Do Not Apply Editing Format for US Planet *Apply Do Not Apply Editing Format for UK Postal *Apply Do Not Apply Editing Format for Japan Postal *Apply Do Not Apply...
Page 250 Chapter 6 Applying Formats for Data Editing Editing Format for Dutch Postal *Apply Do Not Apply Editing Format for USPS 4CB/One Code/Intelligent Mail *Apply Do Not Apply Editing Format for UPU FICS Postal *Apply Do Not Apply Editing Format for PDF417 *Apply Do Not Apply Editing Format for MicroPDF417...
Page 251 1662/1664 Barcode Scanner User Guide Editing Format for Data Matrix *Apply Do Not Apply Editing Format for Maxicode *Apply Do Not Apply Editing Format for QR Code *Apply Do Not Apply Editing Format for MicroQR *Apply Do Not Apply Editing Format for Aztec...
Page 252: Data Length
Chapter 6 Applying Formats for Data Editing 6.3.2 DATA LENGTH The lengt h m ust include prefix, suffix ( 0x0d by default ) , lengt h code, et c. By default , barcodes of any lengt h ( charact er count ) are eligible for dat a edit ing. ...
Page 253: Matching String & Location
1662/1664 Barcode Scanner User Guide 6.3.3 MATCHING STRING & LOCATION By default , no m at ching st ring is specified, and t herefore, it is disabled. You m ay enable t his feat ure by specifying a m at ching st ring; up t o four charact ers are allowed.
Page 254: Configure Format - Define Data Field
Chapter 6 Applying Formats for Data Editing 6.4 CONFIGURE FORMAT — DEFINE DATA FIELD 6.4.1 START POSITION Dat a can be divided int o fields in one of t he following direct ion –  from head ( F1) t o t ail ( F5) ...
Page 255: Total Number Of Fields
1662/1664 Barcode Scanner User Guide 6.4.3 TOTAL NUMBER OF FIELDS Dat a can be divided int o at m ost 6 fields; each of t hem is num bered from F1 t o F6 accordingly. However, only F1~ F5 can be configured.
Page 256: Field Settings
Chapter 6 Applying Formats for Data Editing 6.4.4 FIELD SETTINGS Dat a eligible for edit ing form at s is divided int o fields by user- specified rules – eit her using t he field t erm inat ing st ring or specified field lengt h. By Terminating String Specify t he field t erm inat ing st ring.
Page 257 1662/1664 Barcode Scanner User Guide Field 2 Setting Read t he bar code below t o divide field 2 by a specified t erm inat ing st ring. Select Field Separator to Divide Field 2… Read t he “ Hexadecim al Value”...
Page 258 Chapter 6 Applying Formats for Data Editing Field 3 Setting Read t he bar code below t o divide field 3 by a specified t erm inat ing st ring. Select Field Separator to Divide Field 3… Read t he “ Hexadecim al Value”...
Page 259 1662/1664 Barcode Scanner User Guide Field 4 Setting Read t he bar code below t o divide field 4 by a specified t erm inat ing st ring. Select Field Separator to Divide Field 4… Read t he “ Hexadecim al Value”...
Page 260 Chapter 6 Applying Formats for Data Editing Field 5 Setting Read t he bar code below t o divide field 5 by a specified t erm inat ing st ring. Select Field Separator to Divide Field 5… Read t he “ Hexadecim al Value”...
Page 261 1662/1664 Barcode Scanner User Guide Additional Fields Up t o five addit ional fields can be creat ed for each edit ing form at ; each of t hem is num bered from AF1 t o AF5 accordingly.  ®...
Page 262: Pause Field Setting
Chapter 6 Applying Formats for Data Editing 6.4.5 PAUSE FIELD SETTING Pause Field Time You can lim it t he pause t im e int erval ( 1~ 16) . By default , it is set t o 1 second. Pause Field Time 1~16 sec.
Page 263: Configure Format - Define Transmission Sequence
1662/1664 Barcode Scanner User Guide 6.5 CONFIGURE FORMAT — DEFINE TRANSMISSION SEQUENCE Aft er configuring t he dat a fields and addit ional fields, you m ust now program t he t ransm ission sequence of t hese fields t hat com prise t he final dat a. This field t ransm ission sequence can be assigned in any desired order and fields can be assigned m ult iple t im es as well.
Page 264 Chapter 6 Applying Formats for Data Editing Additional Field 2 Additional Field 3 Additional Field 4 Additional Field 5 Pause Field Null Character Field 3) Read t he “ End” barcode t o com plet e t his set t ing. End Programming…...
Page 265: Programming Examples
1662/1664 Barcode Scanner User Guide 6.6 PROGRAMMING EXAMPLES 6.6.1 EXAMPLE I Extract data from the 10th character to the 19th character... The edit ing form at should be configured as follows: Read t he “ Ent er Set up” barcode t o ent er t he Configurat ion Mode.
Page 266: Exam Ple I I
Chapter 6 Applying Formats for Data Editing 6.6.2 EXAMPLE II Extract the date code, item number, and quantity information from barcodes. Dat a in a barcode is encoded like t his:  From t he 1 charact er t o t he 6 charact er is t he dat e code.
Page 267 1662/1664 Barcode Scanner User Guide End Programming Format...
Page 268: Specifications
SPECIFICATIONS Optical Characteristics 1662 1664 Scan Engine 1D Laser 2D I m ager Light Source Visible Laser Diode Visible Red LED RF Characteristics ® WPAN Module Class 2 com pliance Bluet oot h Coverage ( line- of- sight ) 20 m et ers wit h 3610 ...
Page 269 1662/1664 Barcode Scanner User Guide Electrical Characteristics Bat t ery Rechargeable Li- ion bat t ery — 3.7 V, 850 m Ah Power Adaptor I nput AC 100~ 240 V ( 50/ 60 Hz) Out put DC 5V 2A ( Bat t ery Charger) Operat ing Tem perat ure 0 °...
Page 270: Rm W Are Upgrad E
Updat e Not e: For 1662/ 1664, also choose t o use “ Direct ” USB Virt ual COM int erface. 4) Read t he following barcodes in sequence for t he scanner t o ent er download m ode.
Page 271 1662/1664 Barcode Scanner User Guide Enter Setup Download 5) Run t he download ut ilit y “ ProgLoad.exe” on your com put er. Kernel Program User Program K1664_V* .shx STD1664_V* .shx  For t he com m unicat ion set t ings, select “ RS- 232”...
Page 272: Use Direct Usb Virtual Com
Firmware Upgrade USE DIRECT USB VIRTUAL COM 1) Use t he provided USB cable t o connect 1662/ 1664 t o t he USB port of PC. You will need t o inst all it s driver first ! 2) Read t he following barcodes in sequence t o configure 1662/ 1664 t o use Direct USB Virt ual COM as t he download int erface ( read eit her barcode label ‘100008’...
Page 273: Use Bluetooth ® Dongle
Not e: Because 1662/ 1664 support s t he downloading of firm ware via Direct USB Virt ual COM int erface, t he out put int erface will be set t o t he previously used one upon com plet ion of firm ware upgrade.
Page 274 Appendix I Firmware Upgrade 3) Read t he following barcodes in sequence for t he scanner t o ent er t he download m ode. The scanner will respond wit h beeps t o indicat e it is ready for downloading. Enter Setup Down load 4) Run t he download ut ilit y “...
Page 275: How To Upgrade 3610 Firmware
1662/1664 Barcode Scanner User Guide HOW TO UPGRADE 3610 FIRMWARE Connect 3610 t o t he USB port of PC aft er inst alling it s driver. Refer t o 3.1.1 Connect t o 3610 for t he t arget scanner t o connect t o 3610.
Page 276: Upgrade 3610 Usb Bridge Firmware
Appendix I Firmware Upgrade 3) The 3610 will aut om at ically rest art it self when upgrading firm ware is com plet ed successfully. 4) Read t he “ Updat e” barcode for t he scanner t o resum e it s operat ion ( exit t he configurat ion m ode) .
Page 277 1662/1664 Barcode Scanner User Guide  For t he com m unicat ion set t ings, select “ RS- 232” and t he correct COM port for USB Virt ual COM int erface.  I gnore t he baud rat e set t ing.
Page 278: Host Serial Commands
Appendix II HOST SERIAL COMMANDS SERIAL COMMANDS Purpose To disable t he scanner. “D” Rem arks Purpose To enable t he scanner. “E” Rem arks #@nnnnnn<CR> Purpose To configure t he scanner. Rem arks nnnnnn – t he six digit s of com m and param et ers. For exam ple, “...
Page 279 1662/1664 Barcode Scanner User Guide #@TRIGOFF<CR> Purpose To disable t he soft ware t rigger “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x46” + Rem arks “0x46” + “0x0d” #@TRIGON<CR> Purpose To enable t he soft ware t rigger “0x23”...
Page 280: Example
Appendix II Host Serial Commands For exam ple, ‘# @GLED,09’ is t o have t he scanner blink for 9 t im es. “ 0x23” + “ 0x40” + “ 0x47” + “ 0x4c” + “ 0x45” + “ 0x44” + “ 0x2c” + “ 0x30” + “...
Page 281 1662/1664 Barcode Scanner User Guide #@////<CR>  For t he scanner t o save t he set t ings, send t he serial com m and “ # @109999” – #@101011<CR> #@109999<CR>  For t he scanner t o read t he serial num ber and beep - #@RDSN<CR>...
Page 282: 3610 Setup Barcodes & Serial Commands
Appendix II Host Serial Commands 3610 SETUP BARCODES & SERIAL COMMANDS Norm ally, configure t he 3610 dongle by having a connect ed scanner read 3610- relat ed set up barcodes. 1) Connect 3610 t o t he USB port of PC. You will need t o inst all it s driver first ! 2) Refer t o 3.1.1 Connect t o 3610 for t he t arget scanner t o connect t o 3610.
Page 283: 3610 Serial Commands And Equivalent Setup Barcodes
1662/1664 Barcode Scanner User Guide 3610 SERIAL COMMANDS AND EQUIVALENT SETUP BARCODES Config<CR> Purpose To configure 3610. Here is t he set up barcode for t his serial com m and: Config Rem arks A list of t he current set t ings will be displayed. Run HyperTerm inal.exe on your com put er and change t he set t ings one by one.
Page 284 Appendix II Host Serial Commands UseVariablePort<CR> Purpose To use variable Virt ual COM port when connect ing m ore t han one 3610 t o PC via USB. Here is t he set up barcode for t his serial com m and: UseVariablePort Version<CR>...
Page 285: Example
1662/1664 Barcode Scanner User Guide EXAMPLE Wit hout using t he scanner t o read t he above set up barcodes for configuring t he 3610 dongle, run HyperTerm inal.exe on t he host com put er t o send serial com m ands t o 3610 via USB Virt ual COM.
Page 286: Keyboard Wedge Table
Appendix III KEYBOARD WEDGE TABLE   I NS  "  Hom e    Down &  Left   Right PgUp Exec < PgDn > ENTER* Not e: ( 1) ~ : Digit s of num eric keypad. ( 2) CR* / ENTER* : ENTER key on t he num eric keypad.
Page 287: Key Type & Status
1662/1664 Barcode Scanner User Guide KEY TYPE & STATUS KEY TYPE ® I f “ Bluet oot h HI D” or “ USB HI D” is configured for int erface, Key Type and Key St at us will t hen becom e applicable.
Page 288: Example
Appendix III Keyboard Wedge Table EXAMPLE KEY TYPE = NORMAL For exam ple, if you want t o program t he charact er “ ! ” as t he prefix code: Read t he “ Configure Prefix” barcode. Read t he “ Hexadecim al Value”...
Page 289 1662/1664 Barcode Scanner User Guide Enter Setup...
Page 290: Numeral Systems
Appendix IV NUMERAL SYSTEMS DECIMAL SYSTEM Decimal Validate the Values Validate Update Abort...
Page 291: Hexadecimal System
1662/1664 Barcode Scanner User Guide HEXADECIMAL SYSTEM Hexadecimal Enter Setup...
Page 292: Ascii Table
Appendix IV Numeral Systems Validate the Values Validate ASCII TABLE " & < > Update Abort...
Page 293: Entering Pin Code For Authentication
1662/1664 Barcode Scanner User Guide ENTERING PIN CODE FOR AUTHENTICATION USE PRESET PIN 1) I n t he configurat ion m ode, read t he barcode below t o use a preset PI N for aut hent icat ion. Use Preset PIN 2) Read one of t he barcodes t o specify t he PI N code, in decim al or hexadecim al.
Page 294: Disable Authentication Or Use Random Pin
Appendix IV Numeral Systems DISABLE AUTHENTICATION OR USE RANDOM PIN I n t he configurat ion m ode, read t he barcode below t o disable aut hent icat ion ( = No PI N) or use a random PI N for aut hent icat ion. *No PIN or use random PIN ®...
Page 295 1662/1664 Barcode Scanner User Guide Read t he “ Validat e” barcode t o com plet e t his set t ing. Reject Random PIN Request When t he random PI N is displayed on t he t arget device while pairing, you can rej ect t he PI N request by having t he scanner read t he “...
Page 296: Set Up Driver License (1664 Only)
Appendix V SET UP DRIVER LICENSE (1664 ONLY) 1664 has t he capable of reading 2D driver’s licenses and ot her Am erican Associat ion of Mot or Vehicle Adm inist rat ors ( AAMVA) com pliant I D cards. For com pliant 2D licensed card scanning, it can decode t he inform at ion em bedded in t he I D cards t o a form at t ed dat a.
Page 297: License Data
1662/1664 Barcode Scanner User Guide LICENSE DATA 1664 allows you t o arrange t he sequences of license em bedded dat a via separat ors and fields. I n order t o present dat a in a consist ent form at , som e barcodes ( ex. First Nam e, Middle Nam e/ I nit ial, Last Nam e, Nam e suffix, Nam e Prefix, Birt h Dat e and so on) will ret urn dat a based on t he calculat ed act ual dat a cont ained in t he I D bar code.
Page 298 Appendix V Set up Driver License (1664 only) Mailing Address Postal Code Home Address Line1 Home Address Line2 Home Address City Home Address State Home Address Postal Code License ID Number License Class License Restrictions License Endorsements Height (Feet and/or Inches) Height (Centimeters) Update...
Page 299 1662/1664 Barcode Scanner User Guide Weight (Pounds) Weight (Kilograms) Eye Color Hair Color License Expiration Date Birth Date Gender License Issue Date Issue Timestamp Number of Duplicates Medical Codes Organ Donor Enter Setup...
Page 300 Appendix V Set up Driver License (1664 only) Nonresident Customer ID Social Security Number AKA Birth Date AKA Social Security Name AKA Full Name AKA Last Name AKA First Name AKA Middle Name/Initial AKA Name Suffix AKA Name Prefix Weight Range Update Abort...
Page 301 1662/1664 Barcode Scanner User Guide Document Discriminator Country Federal Commission Codes Place of Birth Audit Information Inventory Control Race/Ethnicity Std Vehicle Class Std Restrictions Std Endorsements Class Description Endorsement Description Enter Setup...
Page 302 Appendix V Set up Driver License (1664 only) Restrictions Description Permit Class Permit Expiration Date Permit ID Number Permit Issue Date Permit Restrictions Permit Endorsements Issuer ID Number Family Name Truncation First Name Truncation Middle Name Truncation Update Abort...
Page 303: Separators And Fields
1662/1664 Barcode Scanner User Guide SEPARATORS AND FIELDS You can define t he separat ors t o separat e Fields during t he t ransm ission sequence of dat a scanning. I n addit ion t o t he built - in dat a elem ent s, you can also specify up t o 5 Addit ional Fields wit h 4 byt es charact ers.
Page 304: Edit Separators
Appendix V Set up Driver License (1664 only) EDIT SEPARATORS All of t he driver license fields can be split wit h a pre- select ed separat or, for exam ple, “ - ” as First Nam e- Last Nam e or “ : ” as First Nam e: Last Nam e. Edit Separator 1 Edit Separator 2 Edit Separator 3...
Page 305: Edit Fields
1662/1664 Barcode Scanner User Guide EDIT FIELDS Up t o five addit ional fields can be creat ed for each edit ing form at ; each of t hem is num bered from Addit ional 1 t o Addit ional 5 accordingly.
Page 306: Keyboard Type One-Scan Barcode
Appendix VI Keyboard Type One-Scan Barcode Appendix VI KEYBOARD TYPE ONE-SCAN BARCODE REMOTE USB HID (VIA 3610) PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) Update Abort...
Page 307 1662/1664 Barcode Scanner User Guide PCAT (Spanish) PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) Enter Setup...
Page 308: Bluetooth Hid
Appendix VI Keyboard Type One-Scan Barcode BLUETOOTH HID PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) Update Abort...
Page 309 1662/1664 Barcode Scanner User Guide PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Dutch) PCAT (Brazilian Portuguese) Enter Setup...

This manual is also suitable for:

1664

CipherLab 1662 User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for CipherLab 1662

Summary of Contents for CipherLab 1662