Hide thumbs Also See for DS3:

Advertisement

Quick Links

INSTALLATION GUIDE
DS3+ / DS4+
2005 Chrysler 300/300c. 933.CHRYSLER 7.34.195.3
Designed by Installers for Installers
© 2022 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Directechs DS3

  • Page 1 INSTALLATION GUIDE DS3+ / DS4+ 2005 Chrysler 300/300c. 933.CHRYSLER 7.34.195.3 Designed by Installers for Installers © 2022 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...
  • Page 2: Table Of Contents

    Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Wiring diagram Locating components in the vehicle Vehicle connections Module programming Key-Type vehicles Push-to-Start (PTS) vehicles Module programming for security-only installations Pairing remotes Connecting the module 8556T Temperature Sensor 8504D Combo Sensor RF Systems When used in conjunction with SmartStart D2D port configuration...
  • Page 3: Introduction

    Introduction This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on the DIRECTLINK text in the header for additional information.
  • Page 4: Vehicle Function Compatibilities

    Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart. Parking Lights Control Ignition Activation Heated Seats Activation RAP Shut Down (Retained ACC Power) Arm Factory Security Remote Start Takeover...
  • Page 5: Pre-Installation And Application Warnings

    Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. Keys T-Harness Keys required required for compatible for operation programming Š...
  • Page 6: Wiring Diagram

    Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( CAN B Low: White, pin 7 Sentry Key Module (black 8-pin conn., connector side view) CAN B High: (-) Ground: Black or White/Orange, Black Striped, pin 4...
  • Page 7: Locating Components In The Vehicle

    Locating components in the vehicle Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. 1A diode [1N4002+] (+) Ignition (-) Ground When Armed (GWA) Output: Red/White: 4 Refer to the Vehicle connections section for wire and Starter (conn.
  • Page 8: Vehicle Connections

    Vehicle connections The connection information listed below is specific to the 2005 Chrysler 300/300c. Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection...
  • Page 9 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/19 Blue (-) Trunk Input No Connection H2/20 Green (-) Door Input No Connection H2/21 Gray (-) Hood Input H2/22 Violet/White (AC) Tach Input No Connection Main harness, 12-pin black connector (H3) Module Connects To Conn./Pin...
  • Page 10 RF Port harness, 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 RF Loop H5/2 RF Loop D2D harness, 4-pin white (1) and black (2) connectors (H6) Module Conn./Pin Color Description H6/1 Blue (Data) TX H6/2 Black (-) Ground H6/3 Green (Data) RX H6/4...
  • Page 11: Module Programming

    Connect the 12-pin main power harness to the module. DS3+: Wait until the LED turns on solid red then proceed to the next step. DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication. Wait until the LED turns ON solid red, then proceed to the next step.
  • Page 12 933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c ©2022 VOXX•DEI LLC. All rights reserved.
  • Page 13: Push-To-Start (Pts) Vehicles

    Connect the 12-pin main power harness to the module. DS3+: Wait until the LED turns on solid red then proceed to the next step. DS4+: The LED turns ON solid blue for 1 second to confirm Bluetooth communication. Wait until the LED turns ON solid red, then proceed to the next step.
  • Page 14 You have successfully completed the module programming sequence. 933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c ©2022 VOXX•DEI LLC. All rights reserved.
  • Page 15: Module Programming For Security-Only Installations

    For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. Must connect 12-pin FIRST DS3+: Connect the 12-pin main power harness to the DS3+ module FIRST. DS3/DS3+ Wait until the LED turns ON solid orange before proceeding to the next step. Solid DS4+: Connect the 12-pin main power harness to the DS4+ module FIRST.
  • Page 16: Pairing Remotes

    Note: Connected devices become registered within 4 to 6 seconds. 8556T Temperature Sensor The 8556T Temperature Sensor is optional, but included with your DS3+/DS4+ module. When used, the Temperature Sensor must be plugged into the 2-pin black connector of your module.
  • Page 17: When Used In Conjunction With Smartstart

    Loops Pigtails DO NOT connect the Directed SmartStart ® 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the D2D connector on the module. Refer to the Directed SmartStart ® documentation for further details. D2D port configuration Caution! Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port.
  • Page 18: Manual Transmission

    S2000, Mazda Miata, and other such vehicles. This system supports manual transmission installations. Refer to “Directwire” section at www.directechs.com for further information on vehicle-specific wiring connections. When flashing the module for Manual Transmission on the Directechs website: In the Remote Start Features section, select the desired configurations for Manual Transmission Initialization & Manual Transmission Completion.
  • Page 19: Led Diagnostics And Troubleshooting

    LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power.
  • Page 20   External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
  • Page 21: Soft Reset

    If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin main 12-pin harness power harness. Press and hold the programming button, then connect the 12-pin harness to the module. DS3+: Wait 3 seconds until the LED turns ON solid orange then release the programming button. & &...
  • Page 22: Tach Learning Procedure (Not Needed With Virtual Tach)

    Tach learning procedure (not needed with Virtual Tach) Data Tach: The procedure is not required as the tach comes preprogrammed. However, it is strongly recommended to learn the exact value of the vehicle for the most consistent and reliable starting and functionality. Hardwired Tach: The procedure is required.
  • Page 23: Limited Lifetime Consumer Warranty

    Limited Lifetime Consumer Warranty VOXX DEI LLC (the Company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or work- manship within the Lifetime from the date of original purchase in the original vehicle, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company’s option) without charge for parts or repair labor.
  • Page 24: Quick Reference Guide

    Quick Reference Guide Sending commands to your vehicle Vehicle takeover with Push-to-Start (PTS) Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, Close the vehicle doors, hood and trunk, then send Press Remote there are 3 possible ways you can send commands to your vehicle, using the: Start button* the Remote Start command to start the vehicle.* •...
  • Page 25 List of available commands For more information, visit www.mysmartstart.com. Note that the information below is for many Viper, Clifford, Python, Autostart and AstroStart models. Icons and commands may differ depending on the model and Notes options purchased. Refer to your authorized installation center for more specific information.

This manual is also suitable for:

Ds3+Ds4Directed ds3+Directed ds4+

Table of Contents