Page 1
O P E R A T I N G I N S T R U C T I O N S T-EASIC FTS Flow sensor...
Page 2
Germany Legal notes This work is protected by copyright. The associated rights are reserved by SICK AG. Reproduction of this document or parts of this document is only permissible within the limits of the legal determination of Copyright Law. No changes, abridgements or translations of this document may be made without the express written consent of SICK AG.
6.2.1 Overview of the electrical connections ...........22 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Page 4
Factory Reset ....................48 O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Page 5
License text ....................69 Notes ....................... 70 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
(e.g., type code and serial number, etc.) before calling. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
IMPORTANT Modifications and conversions to the sensor and/or the installation can result in unforeseeable dangers. Tampering with or modifying the sensor or the SICK software will void any warranty claims against SICK AG. This applies in particular to opening the housing, including during mounting and electrical installation. The prior written consent of the manufacturer must be obtained before making any technical modifications or conversions to the sensor.
Information about the housing Information identifying the sensor (serial number, part number, and type code) and the electrical connection are provided on the housing (see label) of the sensor. 3.1.2 Type code T-Easic FTS Position Description Product group T-Easic FTS (flow sensors) ®...
A detailed description of the buttons and their functions can be found in “7.2.1 Display, LEDs and operating buttons (industrial version only)”. NOTE Both versions of the T-Easic can be programmed using SICK SOPAS-ET via the IO-Link ® 1.1 communication interface. Information on IO-Link can be found in “7.2.4 IO-Link”.
Due to its high temperature resistance, the T-Easic ® is also suitable for use in SIP (Sterilization in Place) processes. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
25 mm 5. NOTE: If a Sick process connection adapter is used (see “14 Accessories”), the 60 mm probe cannot be used at process temperatures above 100 °C as the distances cannot be maintained.
Page 16
Mounting from above is only possible if the pipeline is completely filled with medium. O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
• When sealing the process connection and pipe, take into account the operating pres- sure so as to select the correct sealing method. Mounting the process connection adapter Only use original adapters from SICK. These are available as accessories (see “14 Accessories” on page 66). Fig. 9:...
Fig. 11: Removing a process connection adapter from the sensor probe 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
MOUNTING Mounting in a T-piece Use only original T-pieces from SICK. These are available as accessories (see “14 Accessories”). When mounting in these T-pieces, use the sensor variants with a permanently pre- mounted clamping ring (see “3.1.2 Type code” position 4). During installation, insert the sensor with pre-assembled clamping ring into the T-piece until the clamping ring is seated in the nozzle. Align the sensor so that the arrow on...
The cable connected to the M12 connection is screwed tight. If this is not the case, the device will not meet the specified IP enclosure rating. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
The above table shows only the standard pin assignment. Other pin assignments are possible. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
You can also use the down arrow key to open a submenu. O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
To the left of the display there are three LEDs that indicate the following: Fig. 17: LEDs for industrial version 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Start the system and make sure that the maximum flow rate is reached. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Page 28
O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
If required, configure the delay mode and time (see “7.4.10 Delay Mode Q1”). O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
If required, configure the delay mode and time (see “7.4.10 Delay Mode Q1”). 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
If required, configure the delay mode and time (see “7.4.10 Delay Mode Q1”). O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Fig. 26: Normally closed with empty tube detection O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
6. Increase or decrease the value using the arrow keys (up/down). 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
® O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Page 37
Fig. 29: Explanation of the Q2 digital input and Boolean logic 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Fig. 30: Behavior of the analog output O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Q1 (see “7.4.11 Delay Time Q1”) has elapsed. O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Page 45
Fig. 35: Delay mode Q1 with setting “Ton&Toff Delay”/Hysteresis - normally open 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Failure Failure Simulation is active and the status LEDs S1 and S2 flash simultaneously. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
− Reset All? Reset the values to the factory settings using the arrow keys (up/down). 7.4.21 Password This submenu is reserved for SICK service. 7.4.22 Close Menu Use this submenu to close the advanced configuration menu. The following value is available for selection: −...
MemoryInvalid Failure Device memory contains an invalid Please contact SICK. configuration. The sensor goes into the safe state. Outputdriver Error No.70 Warning Output driver for the switching out- Connect a suitable load (see puts is too warm.
Page 50
Reduce the ambient temperature output is too warm. The ambient according to the specification (see temperature may be too warm, or the “11 Technical data” on page 54) hardware is defective. or contact Sick if necessary. Q2 PulseConfig Warning The pulse output is not configured to Decrease the pulse width or increase match the flow rate. The pulse output the pulse valency.
(see “11 Technical data”). Internal error Failure Internal device error. The sensor Please contact SICK. goes into the safe state. Sensor is not taught Warning The sensor is in teach-in mode, but Correct the minimum and maximum there are no valid teach-in values.
REPAIR Repair Repair work on the sensor may only be performed by qualified and authorized per- sonnel from SICK AG. Tampering with or modifying the sensor will void any warranty claims against SICK AG. Maintenance The T-Easic operates maintenance-free. We recommend that the following measures ® be performed on a regular basis: •...
Dispose of the device components and packaging materials in accordance with the country-specific regulations for waste treatment and disposal applicable to the region. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
25 mm. If a Sick process connection adapter (see “14 Accessories”) is used, the 60 mm probe cannot be used at process temperatures above 100 °C because the distances cannot be maintained.
= 100 cm/s 11.3 Mechanics/materials Without process connection (adapter required for Process connection installation) or with permanently installed clamp- ing ring (only in conjunction with Sick T-pieces) Wetted parts Stainless steel 1.4404/316L Housing material Industrial version: VISTAL (PA66+PA6I GF50) ®...
Analog output available in electrical version B. O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
200(7.87) Fig. 37: Dimensional drawing for industrial version 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Fig. 39: Dimensional drawing for industrial version with clamping ring O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Fig. 40: Dimensional drawing for hygienic version with clamping ring 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Fig. 42: Dimensional drawing of 1/2" NPT adapter (P/N 5338775) O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Fig. 44: Dimensional drawing for clamp connection with weld end (P/N 2121340) 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
DN50 (2122455) with Rp thread O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Fig. 48: Caption: Dimensional drawing for T-piece DN15 (P/N 2123463) with Rp thread 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
0 °C O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Page 65
Deactivated Application-specific indicator Device-specific indicator 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® Subject to change without notice...
You can find further accessories online at www.sick.com O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
Supply Voltage 33.2 °C Sensor Temp 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® Subject to change without notice...
Page 68
Close Menu O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ® 8023072/1E22/2022-02-23 | SICK AG Subject to change without notice...
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 8023072/1E22/2022-02-23| SICK AG O P E R A T I N G I N S T R U C T I O N S | T - E A S I C ®...
Need help?
Do you have a question about the T-EASIC FTS and is the answer not in the manual?
Questions and answers