Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IFM ecomatDisplay CR1077
Summary of Contents for IFM ecomatDisplay CR1077
- Page 1 Operating instructions Process and dialogue module ecomatDisplay CR1077...
-
Page 2: Table Of Contents
CR1077 Contents Preliminary note ............. Symbols used . -
Page 3: Preliminary Note
CR1077 1 Preliminary note You will find instructions, technical data, approvals and further information using the QR code on the unit / packaging or at www.ifm.com. 1.1 Symbols used Requirement Instructions Reaction, result [...] Designation of keys, buttons or indications Cross-reference Important note Non-compliance may result in malfunction or interference. -
Page 4: Safety Instructions
CR1077 2 Safety instructions • The unit described is a subcomponent for integration into a system. – The system architect is responsible for the safety of the system. – The system architect undertakes to perform a risk assessment and to create documentation in accordance with legal and normative requirements to be provided to the operator and user of the system. -
Page 5: Intended Use
If required, take appropriate EMC screening measures. The unit is not approved for safety-related tasks in the field of operator protection. 3.1 Application example Fig. 1: Networking of 4 analogue cameras with an ecomatDisplay ecomatDisplay CR1077 analogue cameras (e.g. 4 x O2M200) 3.2 Properties •... - Page 6 Feature CR1077 Touch screen ● Freely programmable, backlit buttons Navigation keys with button Ethernet interfaces CAN interfaces ifm plug&play (CAN based) USB 2.0 interfaces Analogue video inputs Digital inputs B Digital outputs 2.5 A Line In Speaker output Headphone output Controller Quad core with GPU, 1.2 GHz...
-
Page 7: Installation
EC0731, installation kit for panel mounting • EC1410...EC1414, RAM® mount system for surface mounting More information about available accessories at www.ifm.com 4.2 General installation instructions The following applies to all types of mounting: The responsibility for the compliance with the requirements concerning mounting of the device in the application with regard to shock, vibration, acceleration and weight lies with the system architect. -
Page 8: Light Sensor And Status Led
CR1077 38,1 ® 4 x M5 threaded hole for RAM mount system / for the fixing profile of the installation kit pressure compensation element ATTENTION The device is equipped with a pressure compensation element. Sealing or closing the corresponding ventilation ducts with elastic materials may damage the device. u Do not use any sealing materials in the area around the pressure compensation elements. -
Page 9: Panel Mounting / Control Cabinet Installation
CR1077 4.3 Panel mounting / control cabinet installation 4.3.1 Safety instructions for panel mounting / control cabinet installation The specifications for the operating temperature apply in front of and behind the installation surface. The dimensions for the control panel cut-out are a basic prerequisite for the requirements concerning electrical protection, fire protection and protection rating of the device / system. -
Page 10: Installation With Installation Kit
CR1077 4.3.2 Installation with installation kit The installation kit enables horizontal, vertical or overhead mounting of the device in a panel cut-out. This type of mounting is suited for materials with a thickness from 1 to 10 mm. Longer set screws have to be used for material thicknesses >10 mm. They are not supplied with the mounting accessories. - Page 11 CR1077 Fig. 5: Damping strips u Insert the device into the cut-out. u Insert the spacer suitable for the panel thickness. The thickness of the spacers corresponds to the panel thickness. If necessary, use several spacers on top of each other. u Screw the fixing profile to the back of the device.
-
Page 12: Surface Mounting With Ram® Mount System
2: mounting plate with ball head ® You will find more information about the available RAM mount components at: www.ifm.com 4.4.1 Mounting steps u Screw the mounting plate to the back of the device. Usable M5 thread depth: ≤ 8 mm ±0.5... -
Page 13: Other Installation Types
CR1077 38,1 38 (1,5") Fig. 10: Mounting plate with ball head Fig. 11: Hole dimensions ±0.5 Tightening torque: 5 u Slightly loosen the fastening screw of the mounting arm. u Place the mounting arm onto the ball heads and tighten the fastening screw. 4.5 Other installation types Permissible installation types: Panel mounting / control cabinet installation (Ò / 9) -
Page 14: Electrical Connection
5.1 Wiring Wiring: Technical data: www.ifm.com The terminals may only be supplied with the signals specified in the technical data or on the device label Unconnected pins must not be connected to the cable harness and its individual cores must be sealed. -
Page 15: General Wiring Information
Use twisted-pair cables for the CAN / IFM connection. The CAN bus is internally protected against short circuit to VBB and GND. For CAN / IFM cables ≥ 30 m, ensure appropriate protection against surge (e. g. shielded cables). - Page 16 CR1077 Fig. 12: Connectors (back of the device) supply, inputs/outputs, video, audio, CAN, ifm, service USB0 USB1 ETH0 ETH1 ATTENTION Wrong connection may cause damage to the device. u Observe the safety instructions. ATTENTION The short-circuit / reverse polarity protection of the device applies to the operating voltage connections.
-
Page 17: Operating Voltage And Circuit Breakers
CR1077 5.5 Operating voltage and circuit breakers u The individual electric circuits must be protected in order to protect the whole system. Automotive spade-type fuses are recommended. Required triggering Designation Connector 1 Operating voltage Nominal value fuse characteristics Pin 119 8...16 V DC and 16… ≤... -
Page 18: Ethernet Interface
75 ohms impedance. 5.9 USB interfaces Wiring: Technical data: www.ifm.com This USB interface is connected to a USB connector in the control panel or in the dashboard. It is used for the connection of USB 2.0 devices. -
Page 19: Short-Circuit Protection
CR1077 u If self-assembling cables, please only use cables according to USB 2.0 specification. Keep length "B" as short as possible and position the USB connector in the immediate vicinity of the dialogue module. The length "B" considerably influences the quality of the USB data transmission. -
Page 20: Set-Up
In addition to the CODESYS programming system, the following documents are required for programming and set-up of the device: • Programming manual ecomatDisplay Manuals as well as online help CODESYS and ecomatDisplay are available for download on the internet: www.ifm.com... -
Page 21: Function Of The Internal Temperature Sensor
Current consumption (display illumination etc.) The device heats up considerably under demanding operating conditions. The device temperature must not exceed the maximum permissible value (Technical data: www.ifm.com). The value provided by the internal temperature sensor can e.g. be used for the following actions: •... -
Page 22: Maintenance, Repair And Disposal
Remove the battery and replace it with a new one. Observe the polarity: positive side up Battery type (Technical data: www.ifm.com) u Check sealing areas and sealing for soiling. Clean them, if necessary. u Screw the service cover with 3.0 Nm to restore the protection rating (width across flats 13 or ¼“). -
Page 23: Cleaning The Display Surface
CR1077 7.2 Cleaning the display surface Unsuitable cleaning agents and chemicals may damage the display surface. The following agents are not suited for cleaning the display: • Chemicals dissolving plastics such as methylated spirit, benzine, thinner, alcohol, acetone or ammonia. • paper towels, crepe paper etc.