BENDIX Wingman Advanced FLR20 Service Data page 21

Table of Diagnostic Trouble Codes (DTCs), Causes and Recommended Actions for FLR20 Radars
DTC SPN FMI
140 886 14
141 886 14
142 886 14
143 886 14
144 886 14
145 886 14
146 886 14
147 886 14
148 886 14
149 886 14
150 886 14
158 886 14
159 886 14
160 886 14
161 886 14
162 886 14
163 886 14
164 886 14
165 886 14
166 886 14
167 886 14
168 886 14
169 886 14
170 886 14
171 886 14
172 886 14
173 886 14
174 886 14
175 886 14
176 886 14
177 886 14
178 886 17
179 886 14
181 886 14
182 886 14
183 886 14
184 886 14
185 886 14
186 886 14
187 898 13
188 898 13
189 898 13
190-193 886 14
TABLE 6A - REFER TO COLUMN ONE FOR EACH DTC CODE FOUND AND FIND ITS SERVICE ACTION CODE.
J1939 Signal Error: Error in EEC1 engine speed
J1939 Signal Error: Not available EEC1 engine speed
J1939 Signal Error: Invalid EEC1 driver torque
J1939 Signal Error: Error in EEC1 driver torque
J1939 Signal Error: Not available EEC1 driver torque
J1939 Signal Error: Invalid EEC1 actual torque
J1939 Signal Error: Error in EEC1 actual torque
J1939 Signal Error: Not available EEC1 actual torque
J1939 Signal Error: Invalid EEC2 accelerator pedal position
J1939 Signal Error: Error in EEC2 accelerator pedal position
J1939 Signal Error: Not available EEC2 accelerator pedal position
J1939 Signal Error: Error in VDC1 Roll Over Protection (ROP) brake control
J1939 Signal Error: Not available VDC1 ROP brake control
J1939 Signal Error: Error in VDC1 ROP engine control
J1939 Signal Error: Not available VDC1 ROP engine control
J1939 Signal Error: Error in VDC1 YC brake control
J1939 Signal Error: Not available VDC1 yaw control (YC) brake control
J1939 Signal Error: Error in VDC1 YC engine control
J1939 Signal Error: Not available VDC1 YC engine control
J1939 Signal Error: Invalid VDC2 steer angle
J1939 Signal Error: Error in VDC2 Steer Angle Sensor (SAS)
J1939 Signal Error: Not available VDC2 steer angle
J1939 Signal Error: Invalid VDC2 yaw rate
J1939 Signal Error: Error in VDC2 yaw rate
J1939 Signal Error: Not available VDC2 yaw rate
J1939 Signal Error: Invalid VDC2 long acceleration
J1939 Signal Error: Error in VDC2 long acceleration
J1939 Signal Error: Not available VDC2 long acceleration
J1939 Signal Error: Invalid TSC1 requested torque limit
J1939 Signal Error: Error in TSC1 requested torque limit
J1939 Signal Error: Not available TSC1 requested torque limit
Wingman antenna dirty or partially blocked
Vehicle cruise control and ACC out of sync
J1939 Signal Error: EBC1 ABS not fully operational
J1939 Signal Error: VDC1 VDC not fully operational
J1939 Signal Error: Error in VDC1 VDC fully operational
J1939 Signal Error: Not available VDC1 VDC fully operational
ABS tire size needs recalibration using Bendix
Internal radar sensor error
J1939 Signal Error: Error in ACC1 ACC mode
J1939 Signal Error: Not available ACC1 ACC mode
J1939 Signal CCVS3: Engine not properly confi gured for Wingman Advanced
Internal radar sensor error
Description
ACom
®
Go to the Service
Action Code List
in Table 6B
® Diagnostics
N
O
P
N
O
P
N
O
P
N
O
N
O
N
O
N
O
N
O
P
N
O
P
N
O
P
P
O
P
N
O
C
K
R
S
N
O
T
A
N
O
G
A
21