evoheat EVO270-1 Installation & Operation Manual
Hot water heat pump
Hide thumbs
Also See for EVO270-1:
- Installation & operation manual (21 pages) ,
- Quick start manual (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for evoheat EVO270-1
Summary of Contents for evoheat EVO270-1
-
Page 2: Table Of Contents
Page 1 Evo270-1 Manual Contents 1. Introduction ............................... 2 2. Dimensions ............................... 2 3. Quick Start Guide ............................. 3 4. Safety Instructions ............................ 4 5. Installation ..............................5 5.1 System Installation ..........................5 5.2 Handing & Transportation ........................5 5.3 Location of Installation ........................6 5.3.1 Indoor Installation ......................... -
Page 3: Introduction
EvoHeat unit. Instructions in this manual must always be followed. Failure to comply with these recommendations will invalidate the warranty. Should you have any questions or require technical support, call the EvoHeat office on 1300 859 933 to speak to our team. -
Page 4: Quick Start Guide
Page 3 Evo270-1 Manual 3. Quick Start Guide DO NOT DRILL Do not drill any fixings or attachments into the outer casing of the tank. Drilling into the outer casing of the tank may damage the heating coil and WILL VOID WARRANTY. -
Page 5: Safety Instructions
EvoHeat. • • The Evo270-1 must be installed to conform to all relevant In order to use the unit correctly, run the unit at environment temperature -5°C - 43°C Australian Standards and Industry Codes including but not limited to: Electrical &... -
Page 6: Installation
Evo270-1 Manual 5. Installation 5.1 System Installation Upon receiving the unit, check the packaging for any obvious signs of damage. Inform EvoHeat immediately if there is any evidence of rough handling. Do not drill any fixings or attachments into the outer The P&T valve attached with the unit must be installed. -
Page 7: Location Of Installation
Evo270-1 Manual 5.3 Location of Installation The Evo270-1 is designed for external installation, however, where possible installing the unit under the house eaves or in a sheltered environment may help prolong the life of the system. Heat pumps operate most efficiently with warmer air temperatures, and the outlet air from the unit will always be colder than the inlet air. -
Page 8: Operation
Page 7 Evo270-1 Manual 6. Operation 6.1 The Controller ON/OFF Turn the unit on or off. Select options to increase values DOWN Select options to decrease values CLOCK Set the clock or the timer. HYDROBOOST Turn on/off the electric heater... -
Page 9: Operating Functions
Page 8 Evo270-1 Manual 6.2 Operating Functions EvoHeat have developed a YouTube Channel with video walkthroughs of the different controller functions. Scan the QR code or head to our channel to view the videos we have available https://www.youtube.com/evoheat 6.2.1 Startup & Shutdown Press and hold for 0.5 seconds in the... -
Page 10: Setting & Checking The Target Temperature
Page 9 Evo270-1 Manual 6.2.4 Setting & Checking the Target Temperature In the standby or running interface, press once to check the target temperature of the outlet water. Press again to change the target temperature. After making changes to the desired temperature, press... -
Page 11: Sanitech System
Page 10 Evo270-1 Manual 6.2.7 Sanitech System The Sanitech feature’s purpose is to keep the water free of bacteria such as Legionella by heating the tank water to 70°C for one 30-minute period every week at midnight. An instance when you may want to alter the Sanitech function is if you have solar and would prefer the Sanitech to run during the day, for example at 12pm, rather than midnight. -
Page 12: Setting & Cancelling Timers
Page 11 Evo270-1 Manual 6.2.9 Setting & Cancelling Timers Timers can be set in standard mode, economic mode, auto mode & fast heating mode. They can be set by using buttons or using the touch timing circle. The unit will run during the lit time periods and stop in the dim areas. -
Page 13: Vacation Mode
Page 12 Evo270-1 Manual 6.2.10 Vacation Mode Vacation Mode allows you to turn the unit off to conserve power for an extended period of time, and restart operation on a date you specify. This ensures you have hot water waiting for you upon your return. -
Page 14: Troubleshooting
Page 13 Evo270-1 Manual 7. Troubleshooting Fault Malfunction Reason Elimination Methods Display The water bottom temp. sensor is Check or change the water bottom Bottom water temp. failure open or short circuit. temp. sensor Top tank water temp. The water top tank temp. sensor... -
Page 15: Appendix
Page 14 Evo270-1 Manual 8. Appendix 8.1 Wiring Diagram COMP OUT6 DI06 DI05 OUT2 DI04 DI03 OUT1 DI01 485-B 485-A RESET AT：Ambient temperature BTT：Bottom of tank temperature COMP：Compressor CT：Coil temperature 4V： 4 way valve EEV：Electronic expand valve BRN BLU Y/G FM：Fan motor... -
Page 16: Use Of The P&T Valve
A thermal cut-out could indicate a possibly dangerous situation. Do not reset the thermal cutout until the unit has been serviced by a qualified technician. Contact EvoHeat for a service if this occurs before attempting to reset. Remove the screws and open the cover... -
Page 17: Maintenance
Page 16 Evo270-1 Manual 9. Maintenance Your Evo270-1 will operate most efficiently if regularly inspected as part of your home maintenance schedule. MINOR ANNUAL MAINTENANCE It is recommended that the minor maintenance be performed every 12 months by the dwelling occupant. -
Page 18: Warranty
REGISTER YOUR WARRANTY EvoHeat highly recommend customers complete their warranty details online to ensure efficient warranty claim processing. To register your warranty, scan our QR Code or head to our website and fill in the Warranty Registration Form: https://evoheat.com.au/warranty-registration/...
Need help?
Do you have a question about the EVO270-1 and is the answer not in the manual?
Questions and answers