Johnson Controls YORK YK MaxE Operation Manual page 174

printers
YORK SetpOintS
ChilleR id 0
(c) 1997 – 2001 YORK INTERNATIONAL CORPORATION
Mon 22 Nov 1999 8:48:27 AM
Software Versions
----------------------------------------------------------------------------------
Controls
BIOS
Kernel
GUI
SIO
GPIC
Ext I/O
0110112091996
[Skip if External I/O board is not activated]
VSD [Skip if Motor Type is not VSD]
SSS [Skip if Motor Type is not Mod B SSS] = C.SSS.01.01
System Information
----------------------------------------------------------------------------------
System Language
Data Display Mode
Control Source
Remote Analog Input Range
Clock
Jumper Settings
----------------------------------------------------------------------------------
Pre-Run
Coastdown
Chilled Liquid Pump Operation
Refrigerant Selection
Anti-Recycle
Power Failure Restart
Liquid Type
Motor Type
Printer Setup
----------------------------------------------------------------------------------
Automatic Printer Logging
Log Start Time
Output Interval
Printer Type
Baud
Data Bits
Parity
Stop Bits
COM 2 Setup
----------------------------------------------------------------------------------
Baud
Data Bits
Parity
Stop Bits
Evaporator
----------------------------------------------------------------------------------
Leaving Chilled Local Setpoint
Leaving Chilled ISN Setpoint
Leaving Chilled Modem Setpoint
Leaving Chilled Analog Setpoint
Leaving Chilled Digital Setpoint
fig. 46– SAMPLE PRINTOUT (SETPOINTS)
174
Remote Range
Sensitivity
Restart Offset
Restart Setpoint
Shutdown Offset
Shutdown Setpoint
Brine Low Evaporator Cutout
Smart Freeze
= C.MLM.01.04
Refrigerant
= C.MLM.00.00
= 0.18
Condenser
= 0.28
----------------------------------------------------------------------------------
= 0.23
High Pressure Warning Threshold
= 0.04
Drop Leg
=
Oil Sump
----------------------------------------------------------------------------------
= C.VSD.00.00
Oil Pump Package
Standby Lube
[Skip the following section if Variable Speed Oil Pump
is not installed]
= English
Variable Speed Oil Pump
= English
----------------------------------------------------------------------------------
= Local
Pressure Setpoint
= 0–10 Volts
Control Period
= Enabled
Proximity Probe
----------------------------------------------------------------------------------
High Speed Thrust Bearing Proximity Referenc = 41 Mils
= Standard
= Standard
[Skip the following section if Liquid Level is not
= Standard
= R22
Refrigerant Level Control
= Enabled
----------------------------------------------------------------------------------
= Auto
Level Control
= Water
Setpoint
= Fixed Speed
Period
Proportion Limit Open
Proportion Limit Close
Rate Limit Open
= Disabled
Rate Limit Close
= 12:00 am
= 60 Min
[Skip the following section if Hot Gas Bypass is not
= Okidata
enabled]
= 9600 Baud
Hot Gas
= 8 Bits
----------------------------------------------------------------------------------
= None
Hot Gas
= 1 Bit
Hold Period
Close Percentage
Minimum Load
Maximum Open
= 19200 Baud
= 8 Bits
Surge
= Odd
----------------------------------------------------------------------------------
= 1 Bit
Surge Sensitivity
Shutdown
Extended Run
Count Limit
= 45.0 ~F
Count Window
= 45.0 ~F
= 45.0 ~F
= 45.0 ~F
= 45.0 ~F
FORM 160.54-O1
= 10.0 ~F
= Normal
= 0.0 ~F
= 45.0 ~F
= 4.0 ~F
= 41.0 ~F
= 54.3 Psig
= Off
= Enabled
= 246.3 Psig
= Enabled
= Variable Speed
= On
= 35 Psid
= 0.9 Sec
enabled]
= On
= 50 %
= 3.5 Sec
= 15 %
= 45 %
= 10 %
= 10 %
= Enabled
= 30 Min
= 5 %
= 1 ~F
= 80 %
= 0.3
= Enabled
= Disabled
= 15
= 5 Min
JOHNSON CONTROLS