Johnson Controls YORK YK MaxE Operation Manual page 168

printers
A printer can be connected to the Control Center's
Microboard to print the following reports. The screen
from which each report can be generated is listed in pa-
renthesis.
•
Status - Present system parameters (Printer,
Home)
•
Setpoints - Present programmed values of all set-
points (Printer, Setpoints)
•
Schedule - Present value of programmed daily
schedule (Printer, Schedule)
•
Sales Order - Information on Sales Order Screen
(Printer, Sales Order)
•
History - System parameters at the time of the last
normal stop, last fault while running and last 10
faults, whether running or not (Printer, History)
•
Cycling or Safety shutdown initiated Print - Snap-
shot of all system parameters at instant of shutdown.
Automatically occurs if printer is connected at time
of shutdown.
•
Adaptive Capacity Control (ACC) surge Map
- System conditions at instant all surge points were
mapped. (Compressor Motor Variable Speed Drive
applications; requires SERVICE access level)
(Printer, ACC)
•
T r e n d ( F l a s h M e m o r y c a r d v e r s i o n
C.MLM.01.05.xxx and later) - Prints a snapshot
of the existing trend screen data or prints new data
collected after the trend print key is pressed.
The printer can be permanently connected to the Control
Center or connected as required to produce a report. If
permanently connected, a DATA LOggIng feature
can produce a Status report automatically, beginning
at an Operator selected start time and occurring at an
Operator selected interval thereafter.
The following figures are examples of the different print
reports. Solid State Starter application print reports
shown. Electro-Mechanical starter and Variable Speed
Drive reports are similar but print parameters applicable
to those devices.
•
FIG. 45 - Status
•
FIG. 46 - Setpoints
•
FIG. 47 - Schedule
•
FIG. 48 - Sales Order
•
FIG. 49 - History
•
FIG. 50 - Security Log (Flash Memory Card ver-
sion C.MLM.01.06.xxx and later and
"P" compressors C.MLM.04.02.xxx
and later)
168
priNters
•
Figure 51 - Trend (Flash Memory Card version
•
Figure 52 - Custom Screen (If compressor other
•
Figure 53 - Adaptive Capacity Control New Map
•
Figure 54 - Adaptive Capacity Control Existing
priNters
The following Printers can be used. Printers must be
equipped with an RS-232 Serial interface.
•
Okidata –
Models: 182,182 turbo, 184 turbo
Dimensions: 14 in. wide x 10.5 in. deep
Paper: 8.5 in. wide
Type: Dot matrix impact
Purchase: 800-OKIDATA
•
Weigh-Tronix –
Models: 2600, 1220
Dimensions: 2.3 in. wide x 2.8 in. deep
Paper: 2.25 in. wide
Type: Dot matrix impact
Purchase: USA 800-982-6622
•
Seiko –
Printer: DPU414-30B
Dimensions: 6.3 in. wide x 6.7 in. deep
Paper: 4.4 in. wide
Type: Thermal
Power Supply: PW4007I (required)
Battery Pak (Ni-Mh): BP4005
Thermal paper: SS112-025A
Purchase: Jaco Electronics (formally Reptron
Purchase Contact: Katy Buelow
kbuelow@jacoelect.com
FORM 160.54-O1
C.MLM.01.05.xxx and later)
than "P", applies only to Flash Memory
Card C.MLM.01.04 and later)
point Report
Map points Report
International 707-527-5555
acquired by Jaco)
13710 Reptron Blvd
Tampa, Florida 33626
Phone: 800-800-5441
Fax: 813-891-4056
www.jacoelectronics.com
JOHNSON CONTROLS