GEZE Slimdrive SLT Installation And Service Instructions Manual
  1. Manuals
  2. Brands
  3. GEZE Manuals
  4. Door Opening System
  5. Slimdrive SLT
  6. Installation and service instructions manual
GEZE Slimdrive SLT Installation And Service Instructions Manual

GEZE Slimdrive SLT Installation And Service Instructions Manual

Hide thumbs Also See for Slimdrive SLT:
Table of Contents

Advertisement

Quick Links

Slimdrive SLT
EN Installation and service instructions
Product family
192483-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Slimdrive SLT and is the answer not in the manual?

Questions and answers

Related Manuals for GEZE Slimdrive SLT

Summary of Contents for GEZE Slimdrive SLT

  • Page 1 Slimdrive SLT EN Installation and service instructions Product family 192483-01...

  • Page 2: Table Of Contents

    Mechanical faults ......................................31 Replacing roller carriage ....................................31 Electrical faults........................................ 32 Drive type plate ..............................33 Inspection of the installed door system ....................... 34 10.1 Measures to prevent and secure hazardous areas ..........................34 10.2 Installation checklist Slimdrive SLT ................................. 34...

  • Page 3: Introduction

    If there are several actions to be taken, keep to the given order. Revisions and validity Version 01: valid for Slimdrive SLT product family from date of manufacture 2021 Product liability In compliance with the liability of the manufacturer for his products as defined in the German “Product Liability Act”, compliance with the information contained in this brochure (product information and intended use, misuse,...

  • Page 4: Fundamental Safety Notes

    à in the installation variants / types of installation documented by GEZE à within the tested/approved area of application (climate / temperature / IP rating) Any other use is considered non-intended and will lead to the exclusion of all liability and warranty claims to GEZE. Safety notes à...

  • Page 5: Safety-Conscious Working

    Slimdrive SLT product family Fundamental safety notes The product should be installed or incorporated in such a way that effortless access to the product is guaranteed during any repairs and/or maintenance, and that any removal costs do not stand out of economic proportion to the value of the product.

  • Page 6: About This Document

    3. 1 Overview These instructions describe the installation of automatic sliding door systems of the Slimdrive SLT product family without side panel. The installation of the side panels and the girder section installation is described in the instal- lation instructions “Girder section with side panel”.

  • Page 7: Overview

    Torque spanner Allen key 2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm Open-ended spanner 8 mm, 10 mm, 13 mm, 15 mm, 13 mm flat (GEZE specialised tool) Ring spanner 8 mm Screwdriver set Floor guide slit up to 6 mm, cross-slot PH2 and PZ2...

  • Page 8: Torques

    Installation Slimdrive SLT product family Torques The torques are given at the respective installation step. Components and assembly groups See the ep-drawing for the required installation situation and drive drawings. Installation WARNING! Risk of fatal injury due to electric shock! Do not loosen screw-fitted electrical protective earth connections.
  • Page 9 Slimdrive SLT product family Installation View from above Fastening drill holes Mounting profile Track Sealing profiles Wall strips Determine the installation height of the mounting profile (2). Take unevenness of wall and floor into account. Align the mounting profile (2) horizontally.
  • Page 10 Installation Slimdrive SLT product family Clamping the track with clamping strips WARNING! Risk of injury! Unsecured components may fall when under load. Remove the cap with side plate. The track (3) is clamped to the mounting profile (1) using clamping strips (2) so that the track (3) is attached so as to be prevented from twisting.

  • Page 11: Mounting The Floor Guide

    Slimdrive SLT product family Installation Mounting the floor guide à The floor guide is selected based on the on-site conditions. One of the following floor guide options must be used. à For further information see the respective installation drawing, Chapter 4.1.

  • Page 12: Installing The Moving Leaf

    Installation Slimdrive SLT product family Installing the moving leaf 5.4. 1 Install the door suspension plates on the moving leaf The door suspension plates are installed during glazing of the moving leaves. In case of subsequent installation of the door suspension plates, the frames of the moving leaves must be dismantled (see installation instructions for moving leaves).
  • Page 13 Slimdrive SLT product family Installation 5.4.2 Installing the connecting arm and driver à Drivers must not touch any obstacle over the entire travel path. à See the drive drawing for the precise position of the driver. 4-leaf Installing the connecting arm and long driver:...
  • Page 14 Installation Slimdrive SLT product family 2-leaf Installing the connecting arm and short driver: For drive SLT-FR 2-leaf, right, an angled driver, short (8) is mounted. Use 2 hexagon screws (7) and intermediate plate (9) to screw the short driver (8) to the inner moving leaf (torque 15 Nm).
  • Page 15 Slimdrive SLT product family Installation 5.4.4 Installing the wire rope Overview (4-leaf shown) Rope pulley, short Suspension piece Clamping piece Tensioning piece Wire rope Rope pulley, long Connecting arm Push outer moving leaf into open position. approx. 20 mm Position suspension piece (2) on the track approx 20 mm from the centre axis of the long rope pulley (6) and clamp in position.
  • Page 16 Installation Slimdrive SLT product family Thread the wire rope into the clamping piece (3) and pull through. Position the clamping piece (3) on the track (approx. 30 mm distance from the suspension part (2)) and clamp in position. Tighten the wire rope by hand and secure in the clamping piece (3) (screws from underneath).
  • Page 17 Slimdrive SLT product family Installation 5.4.5 Adjusting the moving leaves WARNING Risk of crushing! The moving leaves are still unsecured and move easily. Ensure that the moving leaves are not moved accidentally or by unauthorised persons! Observe the applicable standards and guidelines on crushing, shearing and drawing-in spots.
  • Page 18 Push the vertically adjustable strip with brush into the moving leaf until it snaps into place (see the assembly drawing for the Slimdrive SL moving leaf). Mount the guide rails in the floor area (see the assembly drawing for the Slimdrive SLT moving leaf). Slide the moving leaves to the closing position.

  • Page 19: Fitting The Tooth Belt

    Slimdrive SLT product family Installation Fitting the tooth belt 1-leaf Screw the toothed belt locking (2) on the short driver (1) (torque 10 Nm). 2-leaf Screw the toothed belt locking (2) on the short driver (1) (torque 10 Nm). Fix the toothed belt locking (1) on the long driver (4) using the screw (3) and the counterplate (2) (torque 10 Nm).
  • Page 20 Installation Slimdrive SLT product family 5.5. 1 Tensioning the tooth belt The tooth belt must be pre-tensioned with 300 N ±35 N (see drive drawing). Undo 2 screws (2). Slide the motor gear unit (3) to the right by hand. Undo the screw (1) and move the sliding block...
  • Page 21 Slimdrive SLT product family Installation 5.5.3 Positioning the tooth belt locking mechanism (optional) Close the moving leaves. Loosen the screws (1) at the tooth belt locking mechanism (optional). Align the locking device to the toothed belt. Following installation, the locking pin (2) must be positioned in the hole in the cover so that the tooth belt locking mechanism can be locked and unlocked.

  • Page 22: Setting The Stop Buffer

    Installation Slimdrive SLT product family Setting the stop buffer During installation, the rubber buffers must point in the direction of the middle of the track. Undo the setscrew (2) on the stop buffer (1). Slide the moving leaf to the open position.

  • Page 23: Fitting The Transformer Ground

    Slimdrive SLT product family Installation Fitting the transformer ground The track is not earthed if there is a poor connection between earthing rail (3) and track. Check whether the setscrews of the earthing rail (3) penetrate the anodised layer of the track.

  • Page 24: Production Test And Commissioning

    Production test and commissioning Slimdrive SLT product family Production test and commissioning 6. 1 Connecting the drive WARNING Risk of fatal injury due to electric shock! The electrical system (230 V) may only be connected and disconnected by a professional electrician.

  • Page 25: Mounting The Cover

    Slimdrive SLT product family Production test and commissioning Mounting the cover WARNING! Risk of injury! People can be injured when handling the cover. Always make sure two people handle the cover. WARNING! Risk of injury from falling cover! Make sure that the cover is attached along the entire length of the track.
  • Page 26 Production test and commissioning Slimdrive SLT product family Push the cords (rubber cables) (4) onto the mounted suspension pieces (1) of the cover. 6.3. 1 Fitting the cover earthing Knock the locating pin for the cover earthing (1) on the side of the earthing approx. 30 mm into the upper screw duct.
  • Page 27 Slimdrive SLT product family Production test and commissioning 6.3.2 Mounting cover fixing brackets Cables can be cut! Lay the cables so that there are no cables near any moving parts. Install cover fixing bracket (1) and fix on a sliding block using locking screw M6 x 16 hexagon socket locking screw (torque 15 Nm).
  • Page 28 Production test and commissioning Slimdrive SLT product family 6.3.4 Attaching the cover Ensure that cables are not crushed or damaged. Slide the cover (3) onto the side panels (2) until it latches in and ensure that it is also seated correctly in the area of the track and cable guides.

  • Page 29: Mounting The Safety Devices

    Slimdrive SLT product family Service and maintenance Mounting the safety devices For information about connection and parameter setting of the safety sensors, and the inputs and outputs and on commissioning, please refer to the wiring diagram. Mount safety and activation equipment.

  • Page 30: Maintenance

    Service and maintenance Slimdrive SLT product family Maintenance CAUTION! Risk of injury due to impact and crushing! Secure door leaves against accidental movement. Disconnect rechargeable battery. Disconnect the mains voltage. à Only original replacement parts may be used. à To ensure proper function, the wear parts of the sliding door system must be inspected and exchanged if necessary during every maintenance.

  • Page 31: Troubleshooting

    Slimdrive SLT product family Troubleshooting Troubleshooting 8. 1 Mechanical faults Cause Remedy Track bent Replace the track Check the installation surface Moving leaf stiff Check the moving leaf (see Chapter 8.1.1) Roller carriage jammed or defective, high abrasion on Replace the track roller (see Chapter 8.2),...

  • Page 32: Electrical Faults

    Troubleshooting Slimdrive SLT product family Electrical faults For read-out instructions and a list of fault messages, see wiring diagram. 8.3. 1 Replacing fuse in transformer DANGER! Risk of fatal injury due to electric shock! If the main switch on the transformer is activated, the fuse is still energised since it is upstream of the main switch.

  • Page 33: Drive Type Plate

    Slimdrive SLT product family Drive type plate Drive type plate Only relevant in Germany and within the scope of validity of DIN 18650-1. Add the classification code to the type plate. Sliding door drive Slimdrive SLT 50 °C Input 230 V 50 Hz 0.65 A...

  • Page 34: Inspection Of The Installed Door System

    – à Installation instructions safety leaf – – Was the type plate for the Slimdrive SLT adhered instead of the type plate for the Slimdrive SL? Type plate added to the sliding door system? Notes: à Only relevant for Germany and within the scope of validity of DIN 18650 à...
  • Page 35 Slimdrive SLT product family...
  • Page 36 E-Mail: leonberg.de@geze.com Baltic States – Iberia Scandinavia – Norway Lithuania / Latvia / Estonia GEZE Iberia S.R.L. GEZE Scandinavia AB avd. Norge GEZE GmbH E-Mail: norge.se@geze.com E-Mail: baltic-states@geze.com E-Mail: info.es@geze.com Niederlassung Süd-Ost www.geze.no www.geze.es Tel. +49 (0) 7152 203 6440 E-Mail: muenchen.de@geze.com...

Table of Contents