GEZE Slimdrive EMD User Manual
Hide thumbs
Also See for Slimdrive EMD:
- Original operating instructions (20 pages) ,
- Replacement instructions manual (20 pages) ,
- Wiring diagram (76 pages)
Related Manuals for GEZE Slimdrive EMD
Summary of Contents for GEZE Slimdrive EMD
- Page 1 Slimdrive EMD Original operating instructions GB User manual Slimdrive EMD-F Slimdrive EMD-F-IS Slimdrive EMD Invers...
-
Page 2: Table Of Contents
Slimdrive EMD / -F / -F-IS / Invers Table of contents Symbols and means of representation .........................3 Revisions and validity .................................3 Product liability ..................................3 Special cases ..................................3 General safety precautions ..........................4 Terms .............................................4 Description .................................6 Types of installation and versions ................................6 Design ...........................................6... -
Page 3: Symbols And Means Of Representation
Slimdrive EMD / -F / -F-IS / Invers Symbols and means of representation Warnings In these instructions, warnings are used to warn against material damage and injuries. Always read and observe these warnings. Observe all the measures that are marked with the warning symbol and warning word. -
Page 4: General Safety Precautions
The service technician must be informed without delay. à GEZE is not liable if products from other manufacturers are used with GEZE equipment. Furthermore, only original GEZE parts may be used for repair and maintenance work. - Page 5 In the event of a power failure, the closing sequence is controlled mechanically on double-leaf door systems with Slimdrive EMD-F-IS. The door leaves are closed by means of the power storage of the drives, with the active leaf being kept open by the integrated mechanical door closing sequence selector at an opening angle of approxi- mately 30°...
-
Page 6: Description
Description Slimdrive EMD / -F / -F-IS / Invers Description 2. 1 Types of installation and versions à The door drive unit can be mounted in transom installation on the lintel or in the door leaf in door leaf installation. -
Page 7: Operation
Slimdrive EMD / -F / -F-IS / Invers Operation Operation 3. 1 Functions The set parameters of the drive functions may only be modified by properly trained persons. The commissioning and setting or changing of door parameters and some special drive functions can be done using the display programme switch, ST 220 or GEZEconnects. -
Page 8: Internal Programme Switch
à In the programme positions I and II the display programme switch (optional) is used to display the operating mode set and to output fault messages. à Special cases (e.g. special circuiting) may occur during the operation of the GEZE door drives. Behaviour may differ. If this is the case, please ask the service technician responsible. -
Page 9: Mechanical Programme Switch Mps (Optional)
Slimdrive EMD / -F / -F-IS / Invers Operation Mechanical programme switch MPS (optional) à Can also be connected to the internal programme switch. At the mechanical programme switch, the system operating mode is selected and the corresponding programme is displayed. -
Page 10: Display Programme Switch (Optional)
Operation Slimdrive EMD / -F / -F-IS / Invers Display programme switch (optional) à Can also be connected to the internal programme switch. à Setting of the operating mode using the display programme switch is only possible when the internal pro- gramme switch is set to the 0 position. -
Page 11: Troubleshooting
Slimdrive EMD / -F / -F-IS / Invers Troubleshooting Troubleshooting Problem Cause Remedy Door only opens and Obstruction in sliding path Remove obstruction and check door leaf closes slowly for ease of movement Safety sensor close (SIS) soiled Clean the safety sensor close... -
Page 12: Cleaning And Maintenance
Cleaning and maintenance Slimdrive EMD / -F / -F-IS / Invers Cleaning and maintenance CAUTION! Danger of injury due to impact and crushing! Disconnect the drive from the 230 V mains network before carrying out cleaning work. Secure door leaves against accidental movement before carrying out cleaning work. -
Page 13: Technical Data
Slimdrive EMD / -F / -F-IS / Invers Technical data Technical data Opening speed: 0°/s … 33°/s Closing speed: 0°/s … 33°/s Electrical connection values: 230 V; 50 Hz pursuant to DIN IEC 38 Connected load: max. 300 W Rated voltage 230 W... - Page 14 Cleaning and maintenance Slimdrive EMD / -F / -F-IS / Invers...
- Page 15 Slimdrive EMD / -F / -F-IS / Invers Cleaning and maintenance...
- Page 16 Hungary Germany Baltic States Scandinavia – Finland GEZE Hungary Kft. GEZE Sonderkonstruktionen GmbH GEZE GmbH Baltic States office Branch office of GEZE Scandinavia AB Bartók Béla út 105-113. Planken 1 Dzelzavas iela 120 S Herralantie 824 Budapest 1021 Riga Postbox 20...
Need help?
Do you have a question about the Slimdrive EMD and is the answer not in the manual?
Questions and answers