Playing Back On Your Tv; Audio Dubbing - Panasonic Palmcorder MultiCam PV-VM202 Operating Instructions Manual

[S-VIDEO IN]
[VIDEO IN]
1
S-VIDEO
IN/OUT
START/
DATE/ PHOTO
OSD TIME SHOT
COUNTER RESET TITLE
MULTI/
A.DUB
P-IN-P
PLAY FF/
STILL ADV PAUSE STILL ADV
INDEX STOP INDEX
SELECT
VAR
W.B./SHUTTER/IRIS/
2
START/
DATE/ PHOTO
STOP
OSD TIME SHOT
COUNTER RESET TITLE ZOOM
T
MULTI/
REC A.DUB
P-IN-P ¥
/REW PLAY FF/
3 V W
W
6 1 5
STILL ADV PAUSE STILL ADV
3, 5
E D
;
INDEX STOP INDEX
K L
∫
SELECT
VAR. P.B.
SEARCH ZOOM
1 2
A.DUB;

Playing Back on Your TV

By connecting your Palmcorder with your TV, the recorded scenes can be
viewed on your TV screen.
≥Before connecting them, turn off the power of both the Palmcorder and TV.
1
Connect the [A/V IN/OUT] Jack of the Palmcorder to the
Video and Audio Input Jacks of the TV.
≥Using the A/V Cable
the TV has an S-Video Jack, connect the S-Video Cable (not supplied)
2
[AUDIO IN]
Making the Indications Appear on the TV screen
Press the [OSD] Button
≥Be sure to select the proper input on your TV. (If necessary, consult your
TV's operating instructions.)
≥If you play back a Cassette recorded with copyright protection signals, the
screen becomes blue or mosaic-like noise patterns appear.
≥If you set [AV JACK] on the [AV IN/OUT SETUP] Sub-Menu to [IN/OUT],
nothing will be shown on the TV screen except during playback.
STOP
ZOOM
T
W
~~~~~~~~~~~~~~~~~~~~~~~~~

Audio Dubbing

P B
You can add music or narration to the recorded Cassette.
≥If you perform audio dubbing onto a tape that was recorded with
[AUDIO-REC] on the [RECORDING SETUP] Sub-Menu of the
[CAMERA FUNCTIONS] Main-Menu set to [16bit], the original sound is
1, 2 erased. (If you want to preserve the original sound, use the [12bit] Mode
MF/VOL/JOG
1
when recording.)
PUSH
≥Audio Dubbing cannot be performed onto recordings made in LP Mode.
1
(l 19)
1
Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> [AV JACK]
>>[IN/OUT].
2
And then select [A.DUB INPUT] >> [MIC] or [AV IN].
≥Set to [AV IN] when an external device is used, or set to [MIC] when
built-in microphone is used.
3
Press the [
point where you want to start dubbing.
4
Press the [A.DUB] Button on the Remote Controller.
≥[A.DUB;] Indication appears.
5
To start Audio Dubbing, press the [;] Button on the Remote
Controller.
≥[A.DUB!] Indication appears.
4
To Stop Audio Dubbing
Press the [;] Button on the Remote Controller.
The Palmcorder is in the Still Playback Mode again.
Playing Back the Sound Recorded with Audio Dubbing
(For 12 bit Audio Recording)
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> [AUDIO] >> [ST2]
or [MIX].
A.DUB!
ST1: Play back only the original sound.
ST2: Play back only the sound added by Audio Dubbing
MIX: Play back both the original sound and the sound added by Audio
Dubbing simultaneously.
≥For other notes, see page 62.
1
(supplied), make a connection with the TV. If
, too.
3
on the Remote Controller.
1 ] Button, and then press the [ ; ] Button at the
1
2
33