ICT PRT-ZX8-DIN Installation Manual page 29

xgNDULx3S--w
INPUTiEXPgNvER
PgSSIVEixOMMUNIxgTION
FIREigLgRMiPgNELi
FIRE
SUPERVISORY
TROU=LE
xOMiSTgTUSiDiF=
AiTheigxiFgILioutputionitheiPoweriSupplyiMUST beiprogrammeditoifollowitheigxiTroubleiInputiasifollows.
i gxiFgILi,iOPENionifail
AiFireiareasishallibeiseparatedifromiburglariareasithroughiareaipartitioningX
AiFireiInputsiZ53Z0ishallibeiusediexclusivelyiforifireimonitoringiandicannotibeiprogrammeditoiactivateitheibellioutput
AFireiInputiZ)iNXOiPushi=uttonitoibeiusediasimonitoringiresetiswitchX
TypicaliInputixircuits
EOL Resitor Input Configuration
Valuei5 Valuei( MonitorediStatus
5K 5K Open1ixlose1iTamper1iShort
9Ks (K( Open1ixlose1iTamper1iShort
58K 58K Open1ixlose1iTamper1iShort
(K( (K( Open1ixlose1iTamper1iShort
)K: (K( Open1ixlose1iTamper1iShort
)K: )K: Open1ixlose1iTamper1iShort
AiEOLiresistorimustibeiinstallediatitheiFireiglarmixontroliPaneliOutputX
Fire area inputs must be programmed as follows:
- FACP Fire Alarm Signal input type must be programmed as Fire.
- Supervisory Trouble Signal input type must be programmed as 24 HR Silent.
- Trouble Signal input type must be programmed as 24 HR Silent.
Please refer to the section
⦁ All fire area inputs must be placed into an area and this area must be armed. Please refer to the section
Inputs | Areas and Input Types
⦁ COM Status
FACP system with a COM STATUS input must have this input connected to one of the dry relay contacts of
the Relay1 or Relay2 outputs of the Protege controller and the selected output must be programmed as the
Report OK output in the Contact ID Service.
Note: Any available dry relay contact on the Protege controller or output expander may be used for the
FACP system, provided the selected output is programmed as the Report OK output.
Please refer to section
Fire inputs Z1-Z3 shall be used exclusively for fire monitoring and cannot be programmed to activate the
⦁
bell output.
PRT-ZX8-DIN | Protege DIN Rail 8 Input Expander | Installation Manual
ENxLOSURE
INPUTiEXPgNvER
Z5
Z(
Z
5(Vvx
3
Z0
)s-
Z)
NXOiInputixontactX
FireiInputimonitoringiRESETiPushi=utton
NXxiInputixontact
NXx
Tamper Valuei( Valuei5
Inputs | Areas and Input Types
in the Operator Reference Manual.
Contact ID | Settings in the Operator Reference Manual.
Metalixonduit Note.igllicablesishallibeiprotectediwithinimetaliconduitsX
ENxLOSURE
ULxicertifiedi5(VivxiPoweriSupply
MgINSiSUPPLY gx Z
V5(8VgxYi
gx 3
)s-
gxi =gTT
5(Vvx FgIL FgIL
Z 3
x Nx x Nx
in the Operator Reference Manual.
()hiStandbyiDi=ackupi
xONTROLLER
RequirediforiTelecomi
Equipmenti
5(Vvx
Z
TELExOMi
3 ETHERNET
EQUIPMENTi
)s-
Programmable
Output
Z 5(Vvx
gUX
3
TELExOMi
vIgLER
)s-
EQUIPMENTi
INTERNET
PSTN
29