Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ICT PRT-IO84-DIN
Summary of Contents for ICT PRT-IO84-DIN
- Page 1 PRT-IO84-DIN Protege DIN Rail 8 Input 4 Output Expander Installation Manual...
- Page 2 Protege® Logo are registered trademarks of Integrated Control Technology Limited. All other brand or product names are trademarks or registered trademarks of their respective holders. Copyright © Integrated Control Technology Limited 2003-2022. All rights reserved. Last Published: 15-Jun-22 5:15 PM PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual...
-
Page 3: Table Of Contents
Error Code Display Mechanical Diagram Mechanical Layout Technical Specifications New Zealand and Australia European Standards UK Conformity Assessment Mark FCC Compliance Statements Industry Canada Statement Disclaimer and Warranty PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 4: Introduction
Secure encrypted RS-485 module communications ⦁ 8 inputs ⦁ 4 Form C Relay outputs ⦁ Industry standard DIN rail mounting ⦁ Online and remote upgradeable firmware ⦁ PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 5: Installation Requirements
Installation Requirements This equipment is to be installed in accordance with: The product installation instructions ⦁ The Local Authority Having Jurisdiction (AHJ) ⦁ PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 6: Grounding Requirements
DIN Rail Enclosure Additional DIN Rail Enclosure(s) Controller Reader Expander Dialer’s Earth Ground Connection Input Expander Power Supply Output Expander AC Mains Wiring Earth Ground Link Connection PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... - Page 7 Note that the DIN rail enclosure earth terminal is connected to the power supply V- terminal. There must be only one single earth grounding point per system. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual...
-
Page 8: Mounting
A Protege DIN rail module can be removed from the DIN rail mount using the following steps: Insert a flat blade screwdriver into the hole in the module tab clip. Lever the tab outwards and rotate the unit off the DIN rail mount. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 9: Dc Power & Encrypted Module Network
RS-485 network cabling. End of Line Resistors: First Module on RS-485 Network Last Module on RS-485 Network 330R 330R From Next Previous Module Module PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 10: Inputs
(open) and restore (closed/sealed) conditions. No EOL Resistor Input Configuration: Trouble Inputs Each input/output expander can monitor up to 16 trouble inputs. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... - Page 11 Aux Failure Power Fault General ZXxxx:05-15 Reserved None None ZXxxx:16 Module Offline Module Offline System Replace 'xxx' with the appropriate address of the module that you are programming. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual...
-
Page 12: Programmable Outputs
A suitable isolation circuit must be installed between the relay contacts of the module and the inductive load. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 13: Address Configuration
The controller has a set limit on the number of modules of each type that it can support. When adding and configuring modules always refer to the Maximum Module Addresses table in the controller installation manual. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 14: Led Indicators
Incorrect module input voltage applied Output Indicators The output indicators will show the status of the outputs. State Description Constantly on (red) Output is ON Constantly off Output is OFF PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 15: Input Status Indicators
Input is in a SHORT state Constantly on Input is in a CLOSED state Constantly on Input is in an OPEN state Fast flash Input is in a TAMPER state PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 16: Error Code Indication
The serial number in the device is not valid. Return the unit to the distributor for replacement. Locked Device The module or system controller is a locked device and cannot communicate on the network. Return the unit to the distributor for replacement. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 17: Mechanical Diagram
Mechanical Diagram The mechanical diagram below outlines the essential details needed to help ensure the correct installation of the input/output expander. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 18: Mechanical Layout
The mechanical layout below outlines the essential details needed to help ensure correct installation and mounting. All measurements are shown in millimeters. 156.80 Front 156.80 42.40 72.00 42.40 Back 139.18 PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 19: Technical Specifications
Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting our website (www.ict.co) for the latest documentation and product information. -
Page 20: New Zealand And Australia
New Zealand and Australia General Product Statement The RCM compliance label indicates that the supplier of the device asserts that it complies with all applicable standards. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 21: European Standards
Tests EMC (operational) according to EN 55032:2015 Radiated disturbance EN 55032:2015 Power frequency magnetic field immunity tests (EN 61000-4-8) EN50131 In order to comply with EN 50131-1 the following points should be noted: PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... - Page 22 ATTACK, comply with the EN 50131 standards. Tamper protection against removal of the cover as well as removal from mounting is provided by tamper switch. Warning: Enclosures supplied by 3rd parties may not be EN50131-compliant, and should not be claimed as such. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual...
-
Page 23: Uk Conformity Assessment Mark
UK Conformity Assessment Mark General Product Statement The UKCA Compliance Label indicates that the supplier of the device asserts that it complies with all applicable standards. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 24: Fcc Compliance Statements
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 25: Industry Canada Statement
This class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. CAN ICES-3 (A)/NMB-3(A) PRT-IO84-DIN | Protege DIN Rail 8 Input 4 Output Expander | Installation Manual... -
Page 26: Disclaimer And Warranty
Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice. - Page 27 In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.
Need help?
Do you have a question about the PRT-IO84-DIN and is the answer not in the manual?
Questions and answers