Error Code Indication Error Code Display Mechanical Diagram Mechanical Layout Technical Specifications New Zealand and Australia European Standards FCC Compliance Statements Industry Canada Statement Disclaimer and Warranty PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
This equipment is to be installed in accordance with: The product installation instructions ⦁ AS/NZS 2201.1 Intruder Alarm Systems ⦁ The Local Authority Having Jurisdiction (AHJ) ⦁ PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
DIN Rail Enclosure Additional DIN Rail Enclosure(s) Controller Reader Expander Dialer’s Earth Ground Connection Input Expander Power Supply Output Expander AC Mains Wiring Earth Ground Link Connection PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Page 7
Note that the DIN rail enclosure earth terminal is connected to the power supply V- terminal. There must be only one single earth grounding point per system. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
A Protege DIN rail module can be removed from the DIN rail mount using the following steps: Insert a flat blade screwdriver into the hole in the module tab clip. Lever the tab outwards and rotate the unit off the DIN rail mount. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
RS-485 network cabling. End of Line Resistors: First Module on RS-485 Network Last Module on RS-485 Network 330R 330R From Next Previous Module Module PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Input 1 on the analog expander. The wiring is equivalent for all available analog inputs. 0-10V OUTPUT DAYLIGHT SENSOR 0-5K / 0-50K LUX DEVICE V+ = +24VDC V- = 24VDC GROUND ANALOG EXPANDER 0V = OUTPUT VOLTAGE 24V+ PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
The shield should not be connected to any shield used for isolated communication. Always refer to the sensor manufacturer for detailed installation guidelines. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
24VDC Output Voltage Low Power Fault General AExxx:04-07 Reserved None None AExxx:08 Module Offline Module Offline System Replace 'xxx' with the appropriate address of the module that you are programming. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
The controller has a set limit on the number of modules of each type that it can support. When adding and configuring modules always refer to the Maximum Module Addresses table in the controller installation manual. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Protege software. State Description Constantly On (green) Analog input is between 0-10V (inclusive) Constantly On (red) Analog input is at 10V or greater PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
The serial number in the device is not valid. Return the unit to the distributor for replacement. Locked Device The module or system controller is a locked device and cannot communicate on the network. Return the unit to the distributor for replacement. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
The mechanical layout shown below outlines the essential details needed to help ensure correct installation and mounting. All measurements are shown in millimeters. 156.80 Front 156.80 42.40 72.00 42.40 Back 139.18 PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting our website (www.ict.co) for the latest documentation and product information.
New Zealand and Australia General Product Statement The RCM compliance label indicates that the supplier of the device asserts that it complies with all applicable standards. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Tests EMC (operational) according to EN 55032:2015 Radiated disturbance EN 55032:2015 Power frequency Magnetic field immunity tests (EN 61000-4-8) EN50131 In order to comply with EN 50131-1 the following points should be noted: PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Page 21
Warning: Enclosures supplied by 3rd parties may not be EN50131-compliant, and should not be claimed as such. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Industry Canada Statement ICES-003 This is a Class A digital device that meets all requirements of the Canadian Interference Causing Equipment Regulations. CAN ICES-3 (A)/NMB-3 (A) PRT-ADC4-DIN | Protege DIN Rail 4 Channel Analog Input Expander | Installation Manual...
Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.
Page 25
Disclaimer: Whilst every effort has been made to ensure accuracy in the representation of this product, neither Integrated Control Technology Ltd nor its employees shall be liable under any circumstances to any party in respect of decisions or actions they may make as a result of using this information. In accordance with the ICT policy of enhanced development, design and specifications are subject to change without notice.